Cutter arbors with tenon drive — Part 2: Dimensions of 7/24 taper

ISO 3937-2:2008 specifies the dimensions of cutter arbors with tenon drive with 7/24 tapers. It also specifies the dimensions of cutter arbors with tenon drive and enlarged contact surface of the cutters.

Mandrins porte-fraise à entraînement par tenons — Partie 2: Dimensions des cônes 7/24

L'ISO 3937-2:2008 spécifie les dimensions des mandrins porte-fraise à entraînement par tenons à cône 7/24 ainsi que les dimensions des mandrins porte-fraise à entraînement par tenons à surface de contact élargie.

General Information

Status
Published
Publication Date
23-Nov-2008
Current Stage
9093 - International Standard confirmed
Completion Date
06-Sep-2018
Ref Project

Relations

Buy Standard

Standard
ISO 3937-2:2008 - Cutter arbors with tenon drive
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 3937-2:2008 - Mandrins porte-fraise a entraînement par tenons
French language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 3937-2
First edition
2008-12-01
Cutter arbors with tenon drive —
Part 2:
Dimensions of 7/24 taper
Mandrins porte-fraise à entraînement par tenons —
Partie 2: Dimensions des cônes 7/24
Reference number
ISO 3937-2:2008(E)
ISO 2008
---------------------- Page: 1 ----------------------
ISO 3937-2:2008(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

COPYRIGHT PROTECTED DOCUMENT
© ISO 2008

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 3937-2:2008(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through

ISO technical committees. Each member body interested in a subject for which a technical committee has

been established has the right to be represented on that committee. International organizations, governmental

and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the

International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 3937-2 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 2, High speed

steel cutting tools and their attachments.

This first edition of ISO 3937-2, together with ISO 3937-1, cancels and replaces ISO 3937:1985, which has

been technically revised.

ISO 3937 consists of the following parts, under the general title Cutter arbors with tenon drive:

⎯ Part 1: Dimensions of Morse taper
⎯ Part 2: Dimensions of 7/24 taper
⎯ Part 3: Dimensions of hollow taper interface with flange contact surface
© ISO 2008 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 3937-2:2008(E)
Cutter arbors with tenon drive —
Part 2:
Dimensions of 7/24 taper
1 Scope

This part of ISO 3937 specifies the dimensions of cutter arbors with tenon drive with 7/24 tapers. It also

specifies the dimensions of cutter arbors with tenon drive and enlarged contact surface of the cutters.

The interchangeability dimensions of the milling cutter bearing on the cutter arbor are in conformity with

ISO 2780. The dimensions of the retaining screw used are specified in ISO 2780.

7/24 tapers are in conformance with ISO 297 for manual changing and with ISO 7388-1 for automatic

changing.
2 Normative references

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced

document (including any amendments) applies.
ISO 297, 7/24 tapers for tool shanks for manual changing

ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual

tolerance indications

ISO 2768-2, General tolerances — Part 2: Geometrical tolerances for features without individual tolerance

indications

ISO 2780, Milling cutters with tenon drive — Interchangeability dimensions for cutter arbors — Metric series

ISO 7388-1, Tool shanks with 7/24 taper for automatic tool changers — Part 1: Dimensions and designation of

shanks of forms A, AD, AF, U, UD and UF
3 Dimensions
3.1 General

All dimensions and tolerances are given in millimetres. Tolerances not specified shall be of tolerance class “m”

in accordance with ISO 2768-1 and of tolerance class “mk” in accordance with ISO 2768-2.

© ISO 2008 – All rights reserved 1
---------------------- Page: 4 ----------------------
ISO 3937-2:2008(E)
3.2 Arbors with 7/24 taper shanks for manual tool changers
3.2.1 General

The dimensions of arbors with 7/24 taper shanks for manual changers are shown in Figure 1.

Key
1 7/24 taper in accordance with ISO 297
...

NORME ISO
INTERNATIONALE 3937-2
Première édition
2008-12-01
Mandrins porte-fraise à entraînement
par tenons —
Partie 2:
Dimensions des cônes 7/24
Cutter arbors with tenon drive —
Part 2: Dimensions of 7/24 taper
Numéro de référence
ISO 3937-2:2008(F)
ISO 2008
---------------------- Page: 1 ----------------------
ISO 3937-2:2008(F)
PDF – Exonération de responsabilité

Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier

peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence

autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées

acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute

responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.

Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info

du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir

l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,

veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2008

Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous

quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit

de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.

ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2008 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 3937-2:2008(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de

normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée

aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du

comité technique créé à cet effet. Les organisations internationales, gouvernementales et non

gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec

la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.

Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,

Partie 2.

La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes

internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur

publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres

votants.

L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne

pas avoir identifié de tels droits de propriété et averti de leur existence.

L'ISO 3937-2 a été élaborée par le comité technique ISO/TC 29, Petit outillage, sous-comité SC 2, Outils

coupants en acier rapide et leurs attachements.

Cette première édition de l'ISO 3937-2, conjointement avec l'ISO 3937-1, annule et remplace l'ISO 3937:1985

qui a fait l'objet d'une révision technique.

L'ISO 3937 comprend les parties suivantes, présentées sous le titre général Mandrins porte-fraise à

entraînement par tenons:
⎯ Partie 1: Dimensions des cônes Morse
⎯ Partie 2: Dimensions des cônes 7/24
⎯ Partie 3: Dimensions des interfaces à cône creux-face
© ISO 2008 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
NORME INTERNATIONALE ISO 3937-2:2008(F)
Mandrins porte-fraise à entraînement par tenons —
Partie 2:
Dimensions des cônes 7/24
1 Domaine d'application

La présente partie de l'ISO 3937 spécifie les dimensions des mandrins porte-fraise à entraînement par tenons

à cône 7/24 ainsi que les dimensions des mandrins porte-fraise à entraînement par tenons à surface de

contact élargie.

Les dimensions d'interchangeabilité de la portée de fraise sur le mandrin porte-fraise sont conformes à

l'ISO 2780. Les dimensions de la vis de retenue utilisée sont spécifiées dans l'ISO 2780.

Les cônes 7/24 sont conformes à l'ISO 297 pour le changement manuel et conformes à l'ISO 7388-1 pour le

changement automatique.
2 Références normatives

Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les

références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du

document de référence s'applique (y compris les éventuels amendements).
ISO 297, Cônes d'emmanchement d'outils à conicité 7/24 pour changement manuel

ISO 2768-1, Tolérances générales — Partie 1: Tolérances pour dimensions linéaires et angulaires non

affectées de tolérances individuelles

ISO 2768-2, Tolérances générales — Partie 2: Tolérances géométriques pour éléments non affectés de

tolérances individuelles

ISO 2780, Fraises à métaux à entraînement par tenons — Dimensions d'interchangeabilité avec les mandrins

porte-fraise — Série métrique

ISO 7388-1, Queues d'outils à conicité 7/24 pour changement automatique d'outils — Partie 1: Dimensions et

désignation des queues de formes A, AD, AF, U, UD et UF
3 Dimensions
3.1 Généralités

Toutes les dimensions et les tolérances sont données en millimètres. Les tolérances non spécifiées doivent

être des tolérances de classe «m» conformément à l'ISO 2768-1 et de classe «mk» conformément à

l'ISO 2768-2.
© ISO 2008 – Tous droits réservés 1
---------------------- Page: 4 ----------------------
ISO 3937-2:2008(F)
3.2 Mandrins à
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.