ISO 11460:2007
(Main)Two-wheeled motorcycles — Positioning of lighting and light-signalling devices
Two-wheeled motorcycles — Positioning of lighting and light-signalling devices
ISO 11460:2006 specifies the requirements for the positioning of lighting and light-signalling devices when fitted to a two-wheeled motorcycle as defined in ISO 3833. It does not specify the installation of any of these devices.
Motocycles à deux roues — Positions des dispositifs d'éclairage et de signalisation lumineuse
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 11460
Second edition
2007-01-15
Two-wheeled motorcycles — Positioning
of lighting and light-signalling devices
Motocycles à deux roues — Positions des dispositifs d'éclairage et de
signalisation lumineuse
Reference number
ISO 11460:2007(E)
©
ISO 2007
---------------------- Page: 1 ----------------------
ISO 11460:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 11460:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11460 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 22,
Motorcycles.
This second edition cancels and replaces the first edition (ISO 11460:1993), which has been technically
revised.
© ISO 2007 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 11460:2007(E)
Two-wheeled motorcycles — Positioning of lighting
and light-signalling devices
1 Scope
This International Standard specifies the requirements for the positioning of lighting and light-signalling
devices when fitted to a two-wheeled motorcycle as defined in ISO 3833. It does not specify the installation of
any of these devices.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3833, Road vehicles — Types — Terms and definitions
ISO 6726, Mopeds and motorcycles with two wheels — Masses — Vocabulary
ISO 7227:1987, Road vehicles — Lighting and light signalling devices — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 6726, ISO 7227:1987 and the
following apply.
3.1
transverse plane
vertical plane perpendicular to the median longitudinal plane of the vehicle
3.2
front position lamp
lamp used to indicate the presence of the vehicle when it is viewed from the front
NOTE This definition differs from that in ISO 7227:1987, 3.17.
3.3
rear position lamp
lamp used to indicate the presence of the vehicle when it is viewed from the rear
NOTE This definition differs from that in ISO 7227:1987, 3.21.
3.4
hazard warning lamp
light signal obtained by simultaneous operation of all the vehicle’s direction indicator lamps
NOTE This definition differs from that in ISO 7227:1987, 3.31.
© ISO 2007 – All rights reserved 1
---------------------- Page: 4 ----------------------
ISO 11460:2007(E)
3.5
separation distance
distance separating two lamps facing in the same direction, between the orthogonal projections in a plane
perpendicular to the reference axes of the outlines of the two illuminating surfaces
NOTE For the full terms and definitions of the illuminating surfaces concerned, see ISO 7227:1987, 3.35 and 3.36.
4 General requirements
4.1 For all light-signalling devices, including those mounted on the side, the reference axis of the lamp
when fitted to the vehicle shall be parallel to the bearing plane of the vehicle on the road. In addition, it shall
be perpendicular to the longitudinal median plane of the vehicle in the case of side reflex-reflecting devices,
and parallel to that plane in the case of all other devices.
A tolerance of ± 3° is allowed in each direction.
In addition, if specifications for fitting are provided by the manufacturer, they shall be met.
4.2 In the absence of specific instructions, the height and orientation of the lamp shall be verified with the
vehicle unladen and placed on a flat horizontal surface, with its median longitudinal plane vertical and the
handlebars in the position corresponding to straight ahead.
4.3 In the absence of specific instructions,
a) single lamps or reflectors shall be mounted such that their centre of reference lies in the median
longitudinal plane of the vehicle;
b) lamps constituting a pair and having the same function shall
1) be mounted symmetrically in relation to the median longitudinal plane,
2) be symmetrical to one another in relation to the median longitudinal plane.
4.4 In the absence of specific instructions, lamps having different functions may be independent, or
grouped, combined or incorporated in one device, on condition that each such lamp satisfies the individual
requirements applicable to it.
4.5 The maximum height above ground shall be measured from the highest point and the minimum height
from the lowest point of the illuminating surface.
4.6 This International Standard defines the positions of the following lighting and light-signalling devices:
⎯ driving/main-beam headlamp (see 5.1);
⎯ passing/dipped-beam headlamp (see 5.2);
⎯ front position lamp (see 5.3);
⎯ side reflex-reflecting device (see 5.4);
⎯ rear reflex-reflecting device (see 5.5);
⎯ direction indicator lamp (see 5.6);
⎯ stop lamp (see 5.7);
⎯ rear position lamp (see 5.8);
2 © ISO 2007 – All rights reserved
---------------------- Page: 5 ----------------------
ISO 11460:2007(E)
⎯ rear registration-plate lamp (see 5.9);
⎯ hazard warning lamp (see 5.10);
⎯ front fog lamp (see 5.11);
⎯ rear fog lamp (see 5.12).
4.7 If fitted, the positioning of each of the lighting and light-signalling devices given in 4.6 shall be effected
in conformity with the relevant requirements in Clause 5.
5 Specific requirements
5.1 Driving/main-beam headlamp
5.1.1 Position
5.1.1.1 A driving/main-beam headlamp may be either independent or reciprocally incorporated with
another front headlamp.
5.1.1.2 In the case of a motorcycle equipped with an independent driving/main-beam headlamp, it may
be fitted either above, below or on either side of another front lamp.
If these lamps are one above the other, the reference centre of the driving/main-beam headlamp shall be
located in the median longitudinal plane of the vehicle.
If these lamps are side by side, their reference centres shall be symmetrical in relation to the median
longitudinal plane of the vehicle.
5.1.1.3 In the case of a motorcycle equipped with a driving/main-beam headlamp that is reciprocally
incorporated with another front lamp, it shall be fitted in such a way that its reference centre lies in the median
longitudinal plane of the vehicle.
However, when the vehicle is also fitted with an independent passing/dipped-beam headlamp or a
passing/dipped-beam headlamp that is reciprocally incorporated with a front position lamp alongside the
driving/main-beam headlamp, their reference centres shall be symmetrical in relation to the median
longitudinal plane of the vehicle.
5.1.1.4 In the case of a motorcycle equipped with two driving/main-beam headlamps of which either one
or both are reciprocally i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.