ISO 17080:2005
(Main)Manually portable agricultural and forestry machines and powered lawn and garden equipment — Design principles for single-panel product safety labels
Manually portable agricultural and forestry machines and powered lawn and garden equipment — Design principles for single-panel product safety labels
ISO 17080:2005 establishes principles and gives requirements for the design of single-panel product safety labels intended to be permanently affixed to manually portable agricultural and forestry machines and powered lawn and garden equipment.
Tracteurs et matériels agricoles et forestiers portatifs et matériels à moteur pour jardins et pelouses — Principes de conception des étiquettes de sécurité de produit à encadré unique
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 17080
First edition
2005-10-15
Manually portable agricultural and
forestry machines and powered lawn and
garden equipment — Design principles
for single-panel product safety labels
Tracteurs et matériels agricoles et forestiers portatifs et matériels à
moteur pour jardins et pelouses — Principes de conception des
étiquettes de sécurité de produit à encadré unique
Reference number
©
ISO 2005
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17080 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and
forestry, Subcommittee SC 14, Operator controls, operator symbols and other displays, operator manuals.
Introduction
There is need for a standardized system for the communication of specific safety information on products, and
ISO 17080 helps meet that need by providing formats for single-panel product safety labels that can be used
to fulfil the requirements of both the product and its user.
The formats for single-panel product safety labels presented in this International Standard incorporate the use
of geometric shapes, colours and hazard pictorials (graphical symbols) to communicate safety information,
efficiently, across language barriers.
Education is an essential part of any system of safety information. Because the amount of information
necessary to enable a product to be operated or serviced safely could well be more than is able to be
conveyed in a product safety label, collateral material (e.g. product literature, installation manual, operator's
manual, service manual, etc.) can be used to supplement product safety labels and provide the user with
additional safety information.
iv © ISO 2005 – All rights reserved
INTERNATIONAL STANDARD ISO 17080:2005(E)
Manually portable agricultural and forestry machines and
powered lawn and garden equipment — Design principles for
single-panel product safety labels
1 Scope
This International Standard establishes principles and gives requirements for the design of single-panel
product safety labels intended to be permanently affixed to manually portable agricultural and forestry
machines and powered lawn and garden equipment. The main usage of these labels is on machines and
equipment where the available space for locating product safety information is very limited, and where multi-
panel labels are not necessary for conveying the essential safety messages.
2 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
2.1
hazard
source of potential injury to a person
2.2
panel
area of a product safety label that has a distinctive background colour different from adjacent areas of the
label, or which is clearly delineated by a border
2.3
multi-panel product safety label
product safety label that uses more than one panel to communicate the safety message
NOTE See ISO 11684.
2.4
product safety label
label on a product that informs the observer of one or more hazards and/or describes the safety precautions
or actions required to avoid the hazard(s)
NOTE A product safety label communicates a hazardous situation, a precaution to avoid a hazard, and/or a result of
not avoiding a hazard.
2.5
safety colour
colour with special properties to which a safety meaning is attributed
2.6
single-panel product safety label
product safety label that uses one panel to communicate the safety message
3 Safety colours and contrast colours
3.1 Purposes
There are two basic purposes for using specific colours on a product safety label. First, the use of colour
rapidly draws attention to the product safety label so that it is easily noticed. Second, safety colour coding
serves to identify and give meaning (through training and/or repeated exposure) to the product safety label as
a whole as well as to its component parts.
Product safety labels should be conspicuous on the product. This can be achieved by
⎯ ensuring that the safety colour of the geometric shape is sufficiently distinctive on the product surface to
which the product safety label is affixed, and/or
⎯ adding a border of a specified contrast colour (see 4.4, 4.5, 4.6), and/or
⎯ enclosing the geometric shape within a larger rectangle of white or — for hazard description (warning)
labels — of yellow or white.
3.2 Chromaticity
The chromaticity of the single-panel product safety labels shall be in accordance with Table 1.
Table 1 — Chromaticity of single-panel product safety labels
Chromaticity coordinates of corner points determining permitted colour area
for standard illuminant D65 and CIE 2° standard observer
Colour
1 2 3 4
x 0,660 0,610 0,700 0,735
Red
y 0,340 0,340 0,250 0,265
x 0,494 0,470 0,493 0,522
Yellow
y 0,505 0,480 0,457 0,477
x 0,140 0,160 0,160 0,140
Blue
y 0,140 0,140 0,160 0,160
x 0,305 0,335 0,325 0,295
White
y 0,315 0,345 0,355 0,325
x 0,385 0,300 0,260 0,345
Black
y 0,355 0,270 0,310 0,395
NOTE The values for red, yellow, blue and white correspond to the values for ordinary materials given in ISO 3864-1:2002, Table 3,
while those for black correspond to the values in ISO 3864-1:2002, Table 2.
2 © ISO 2005 – All rights reserved
4 Single-panel product safety labels
4.1 Uses of label
A single-panel product safety label can be used alone to describe a hazard, a prohibited action, or a
mandatory action. In many cases, both hazard description and hazard avoidance information must be
communicated for the same hazard. A multi-panel product safety label (see ISO 11684) is appropriate in such
cases. Alternatively, it is possible to use two or more single-panel product safety labels in conjunction with one
another. For example, a single-panel hazard description (warning) product safety label may be placed
adjacent to a single-panel mandatory action product safety label and/or single-panel prohibited action product
safety label.
4.2 Types of label
There are three types of single-panel product safety label
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.