ISO 22763:2006
(Main)Equipment for crop protection — Sprayers — Demonstration track for field crop sprayers
Equipment for crop protection — Sprayers — Demonstration track for field crop sprayers
ISO 22763:2006 specifies a uniform demonstration track for showing the spray boom movement of field crop sprayers in, for example, practical demonstrations. The track specified can be used in demonstrations for mounted, trailed or self-propelled sprayers.
Matériel de protection des cultures — Pulvérisateurs — Piste de démonstration pour les pulvérisateurs
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 22763
First edition
2006-09-01
Equipment for crop protection —
Sprayers — Demonstration track for field
crop sprayers
Matériel de protection des cultures — Pulvérisateurs — Piste de
démonstration pour les pulvérisateurs
Reference number
ISO 22763:2006(E)
©
ISO 2006
---------------------- Page: 1 ----------------------
ISO 22763:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 22763:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 General. 1
3 Section A — Field track. 2
4 Section B — Headland turning track . 3
5 Section C — Bumpy track. 4
5.1 Subsections. 4
5.2 Obstacle, test bumps and ramps . 5
5.2.1 Break-back test . 5
5.2.2 Furrow test . 6
Annex A (normative) Sequence of blocks and spaces over total length of field track. 7
© ISO 2006 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 22763:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 22763 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and
forestry, Subcommittee SC 6, Equipment for crop protection.
This first edition of ISO 22763 cancels and replaces ISO/TS 22763:2002, of which it constitutes a technical
revision.
iv © ISO 2006 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 22763:2006(E)
Introduction
The movement of the spray boom is an important performance criterion for field crop sprayers. During
practical demonstrations, the sprayers are driven on demonstration tracks to give the visual impression of the
boom movement. The tracks used are very different.
This International Standard specifies a uniform track that can be used for practical demonstrations. As the
intention is to show the boom movement visually, not to measure it, and due to the conditions under which
practical demonstrations are normally performed, it gives the main characteristics — but not all details —
required in, for example, laboratory measurements.
This demonstration track includes three individual sections which respectively
⎯ represent field conditions (Section A), defined by evaluating real, rough field surfaces,
⎯ show the headland situation (Section B), including an extreme obstacle (simulating, for example, a potato
dam), and
⎯ include a combination of obstacles (Section C) to show boom movement under very rough conditions
exceeding normal/real conditions.
Section A, simulating field conditions, is based on detailed research. It has been proven that this track
represents field conditions and excites a wider range of signals than previous demonstration tracks.
© ISO 2006 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 22763:2006(E)
Equipment for crop protection — Sprayers — Demonstration
track for field crop sprayers
1 Scope
This International Standard specifies a uniform demonstration track for showing the spray boom movement of
field crop sprayers in, for example, practical demonstrations. The track specified can be used in
demonstrations for mounted, trailed or self-propelled sprayers.
2 General
2.1 The demonstration track may consist of the following sections (see Figure 1):
⎯ Section A, field track;
⎯ Section B, headland turning track;
⎯ Section C, bumpy track.
While Sections B and/or C are optional, the demonstration track shall include Section A.
2.2 National and local regulatory conditions and health and safety requirements for visitors and operators
should be observed and followed.
Key
a
A field track Start/driving direction.
b
B headland turning track Acceleration zone.
C bumpy track
r radius
Figure 1 — Demonstration track (Sections A, B and C) — Top view
© ISO 2006 – All rights reserved 1
---------------------- Page: 6 ----------------------
ISO 22763:2006(E)
2.3 The demonstration track shall provide equal conditions for all sprayers independently of when the
sprayers are passing over the track. To this end, the ground surface of the demonstration track shall be hard
and solid across the total track length. Test blocks, bumps and ground surface shall withstand the loads
without deformation or change of position generated by the sprayers or tractor/sprayer combinations
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.