65.060.40 - Plant care equipment
ICS 65.060.40 Details
Plant care equipment
Gerate zur Pflanzenpflege
Matériel de traitement agropharmaceutique
Oprema za nego rastlin
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 65.060.40 - Plant care equipment
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
- Amendment15 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment15 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard6 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
This document specifies requirements and the means for their verification for the design and performance of fixed wing and rotary aircraft spray systems for agriculture, forestry, turf, and vegetation control in transport access ways (such as gas and electric lines) with regard to minimizing the potential risk of environmental contamination during use, including misuse foreseeable by the manufacturer.
It is intended to be used with ISO 16119 1, which gives general requirements common to all the sprayer types covered by ISO 16119. When requirements of this document are different from those stated in ISO 16119 1, the requirements of this document take precedence over the requirements of ISO 16119 1 for machines within the scope of this document.
This document does cover safety of aerial spray equipment not covered by ISO 4254 series.
This document is not applicable to sprayers manufactured before the date of its publication, or unmanned aerial vehicles (such as drones).
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements and the means for their verification for the design and performance of aerial fixed wing and rotary aircraft spray systems for agriculture, forestry, turf, and vegetation control in transport access ways (such as gas and electric lines) with regard to minimizing the potential risk of environmental contamination during use, including misuse foreseeable by the manufacturer.
It is intended to be used with ISO 16119-1:2013, which gives general requirements common to all the sprayer types covered by ISO 16119. When requirements of this document are different from those stated in ISO 16119-1:2013, the requirements of this document take precedence over the requirements of ISO 16119-1:2013 for machines within the scope of this document.
This document does cover safety of aerial spray equipment not covered by ISO 4254 series.
This document is not applicable to sprayers manufactured before the date of its publication, or unmanned aerial vehicles (such as drones).
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements and the means for their verification for the design and performance of aerial fixed wing and rotary aircraft spray systems for agriculture, forestry, turf, and vegetation control in transport access ways (such as gas and electric lines) with regard to minimizing the potential risk of environmental contamination during use, including misuse foreseeable by the manufacturer. It is intended to be used with ISO 16119-1:2013, which gives general requirements common to all the sprayer types covered by ISO 16119. When requirements of this document are different from those stated in ISO 16119-1:2013, the requirements of this document take precedence over the requirements of ISO 16119-1:2013 for machines within the scope of this document. This document does cover safety of aerial spray equipment not covered by ISO 4254 series. This document is not applicable to sprayers manufactured before the date of its publication, or unmanned aerial vehicles (such as drones).
- Standard11 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document, when used together with ISO 16119-1, specifies the requirements and the means for verification of the design and performance of unmanned aerial spraying systems (UASS) mounted on unmanned aircraft systems (UAS) for application of plant protection products (PPPs) in agriculture, forestry, turf and amenity areas, with regard to minimising the potential risk of environmental contamination during use, including misuse foreseeable by the UASS manufacturer. The requirements of this document take precedence over those of ISO 16119-1. The ISO 23117 series does not cover human safety aspects of UASS’s or safety aspects concerning UAS’s, remote pilots or bystanders. This document is not applicable to UASS mounted on UASs with a maximum take-off mass greater than 150 kg. This document is not applicable to UASSs manufactured before the date of its publication.
- Standard12 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
This document defines requirements on the electronic measurements (during spray operation) and recording of operator-controlled application parameters that influence spray drift, when specified for certain drift reduction technologies (DRT). The values measured and recorded can be used to compare the setting of the sprayer with the provisions authorized for the specific DRT. The document is applicable for sprayers for both field and tree and bush crops. It does not apply to hand held and portable sprayers. The following parameters are covered in this document: a) spray pressure (pressure of the spray liquid and air in case of twin-fluid nozzles); b) nozzle height (field crop sprayers); c) fan rotational speed (for air assisted sprayers); d) sprayer forward speed. This document does not specify: — the exact length of the recording period; — the verification of the measured and recorded parameters; — the requirements for data format and exchange because they are covered by other ISO standards. This document does not specify which of the four parameters needs to be monitored.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
2021-10-01: This A11 includes revised Annex ZA to EN ISO 4254-6:2020, both WIs will be presented to EC for citation
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
This document, intended to be used together with ISO 4254-1, specifies the safety requirements and their verification for the design and construction of the following types of root crop harvesting machines trailed, mounted or self-propelled: — sieving harvesters, — root lifting harvesters, — top lifting harvesters, which carry out more than one of the following operations: haulm/leaf topping, digging/taking-in/lifting, cleaning, conveying and unloading of root crops. This document is also applicable for haulm/leaf toppers used individually. This document is not applicable to cleaner-loaders which operate from a heap of beet. For these type of machines, additional hazards are, at present, not dealt with in this document. In addition, it specifies the type of information on safe working practices to be provided by the manufacturer. The list of significant hazards covered in this document is given in Annex A. It also indicates the hazards which have not been dealt with. Environmental aspects have not been considered in this document. Noise has been considered partly in this document. This document applies primarily to machines which are manufactured after the date of its publication.
- Standard54 pagesEnglish languagesale 15% off
- Standard55 pagesFrench languagesale 15% off
2021-10-01: This A11 includes revised Annex ZA to EN ISO 4254-6:2020, both WIs will be presented to EC for citation
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the method of testing the agitation system performance in spray tanks of sprayers for application of plant protection products and fertilizers. This document is not applicable for manually operated knapsack sprayers, aircraft, or UASS sprayers.
- Standard9 pagesEnglish languagesale 15% off
- Standard9 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
This document specifies the requirements, test methods and verification of the inspection of aerial fixed wing and rotary aircraft spray systems for agriculture, forestry, turf, and vegetation control in transport access ways (such as gas and electric lines), with regard to minimizing the potential risk of environmental contamination during use.
This document applies only to manned aerial aircraft. It does not cover aircraft safety and design criteria for air worthiness, aircraft registration, pilot or operator requirements, all of which are specified separately by countries or regions.
This document relates mainly to the condition of the equipment with respect to its potential risk for the environment and its performance to achieve good applications.
The general requirements of ISO 16122-1 apply where appropriate, including for the protection of inspectors during an inspection.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document, to be used together with ISO 4254-1, specifies the safety requirements and their verification for the design and construction of mounted, semi-mounted, trailed and self-propelled agricultural sprayers for use with plant protection products (PPP) and liquid fertilizer application, as placed on the market by the manufacturer and designed for a single operator only. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
When requirements of this document are different from those which are stated in ISO 4254-1, the requirements of this document take precedence over the requirements of ISO 4254-1 for machines that have been designed and built according to the provisions of this document.
This document, taken together with ISO 4254-1, deals with significant hazards, hazardous situations and events relevant to sprayers and liquid fertilizer distributors when they are used as intended and under the conditions foreseeable by the manufacturer (see Annex A), excepting the hazards arising from:
— protection of the driver against spray when spraying (see Foreword);
— automatically actuated height adjustment systems;
— the environment, other than noise;
— moving parts for power transmission except strength requirements for guards and barriers.
This document is not applicable to sprayers and liquid fertilizer distributors which are manufactured before the date of publication of this document.
- Standard36 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies safety requirements and their verification, environmental requirements and
related test methods, and minimum performance limits, for the design and construction of knapsack
combustion engine-driven airblast sprayers as defined in 3.9.
It describes methods for the elimination or reduction of hazards arising from their use. In addition, it
specifies the type of information on safe working practices to be provided by the manufacturer.
It addresses general operating parameters as well as the potential deposition of spray droplets under
specified controlled conditions.
This document deals with all significant hazards, hazardous situations and events, excepting those
arising from vibration transmitted to the back of the operator.
It is applicable to knapsack combustion engine-driven airblast sprayers when they are used as intended
and under the conditions foreseeable by the manufacturer (see Table A.1).
It is not applicable to:
— hydraulic pressure sprayers;
— thermal sprayers;
— cold foggers;
— sprayers adapted for the application of dry material.
It is not applicable to knapsack combustion engine-driven airblast sprayers manufactured before the
date of its publication. The requirements of this document applies to products manufactured 18 months
after publication.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies safety requirements and their verification, environmental requirements and related test methods, and minimum performance limits, for the design and construction of knapsack combustion engine-driven airblast sprayers as defined in 3.9.
It describes methods for the elimination or reduction of hazards arising from their use. In addition, it specifies the type of information on safe working practices to be provided by the manufacturer.
It addresses general operating parameters as well as the potential deposition of spray droplets under specified controlled conditions.
This document deals with all significant hazards, hazardous situations and events, excepting those arising from vibration transmitted to the back of the operator.
It is applicable to knapsack combustion engine-driven airblast sprayers when they are used as intended and under the conditions foreseeable by the manufacturer (see Table A.1).
It is not applicable to:
— hydraulic pressure sprayers;
— thermal sprayers;
— cold foggers;
— sprayers adapted for the application of dry material.
It is not applicable to knapsack combustion engine-driven airblast sprayers manufactured before the date of its publication. The requirements of this document applies to products manufactured 18 months after publication.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies operator and environment-related safety requirements and the means of their verification for the design and construction of closed transfer systems (CTS) for liquid formulations of plant protection products (PPP) in 1 l to 20 l containers. In addition, it specifies the type of information on safe working practices including information about residual risks to be provided by the CTS manufacturer and specifies the maximum potential contamination during any single transfer operation.
- Standard21 pagesEnglish languagesale 15% off
- Standard21 pagesEnglish languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
This International Standard specifies the requirements and test methods for their verification for inspection in use for aerial fixed wing and rotary aircraft spray systems for agriculture, horticulture forestry and human health, with respect to minimizing the risk of environmental.
This part of ISO 16122 relates mainly to the condition of the equipment with respect to its potential risk for the environment and its performance to achieve good applications.
NOTE: Requirements for the protection of inspectors during an inspection are given in ISO 16122-1.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document, to be used together with ISO 4254-1, specifies the safety requirements and their
verification for the design and construction of mounted, semi-mounted, trailed and self-propelled
agricultural sprayers for use with plant protection products (PPP) and liquid fertilizer application,
as placed on the market by the manufacturer and designed for a single operator only. In addition, it
specifies the type of information on safe working practices (including residual risks) to be provided by
the manufacturer.
When requirements of this document are different from those which are stated in ISO 4254-1, the
requirements of this document take precedence over the requirements of ISO 4254-1 for machines that
have been designed and built according to the provisions of this document.
This document, taken together with ISO 4254-1, deals with significant hazards, hazardous situations
and events relevant to sprayers and liquid fertilizer distributors when they are used as intended and
under the conditions foreseeable by the manufacturer (see Annex A), excepting the hazards arising from:
— protection of the driver against spray when spraying (see Foreword);
— automatically actuated height adjustment systems;
— the environment, other than noise;
— moving parts for power transmission except strength requirements for guards and barriers.
This document is not applicable to sprayers and liquid fertilizer distributors which are manufactured
before the date of publication of this document.
- Standard36 pagesEnglish languagesale 10% offe-Library read for1 day
This document, to be used together with ISO 4254-1, specifies the safety requirements and their verification for the design and construction of mounted, semi-mounted, trailed and self-propelled agricultural sprayers for use with plant protection products (PPP) and liquid fertilizer application, as placed on the market by the manufacturer and designed for a single operator only. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer. When requirements of this document are different from those which are stated in ISO 4254-1, the requirements of this document take precedence over the requirements of ISO 4254-1 for machines that have been designed and built according to the provisions of this document. This document, taken together with ISO 4254-1, deals with significant hazards, hazardous situations and events relevant to sprayers and liquid fertilizer distributors when they are used as intended and under the conditions foreseeable by the manufacturer (see Annex A), excepting the hazards arising from: — protection of the driver against spray when spraying (see Foreword); — automatically actuated height adjustment systems; — the environment, other than noise; — moving parts for power transmission except strength requirements for guards and barriers. This document is not applicable to sprayers and liquid fertilizer distributors which are manufactured before the date of publication of this document.
- Standard19 pagesEnglish languagesale 15% off
- Standard19 pagesEnglish languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
This document specifies the requirements, test methods and verification of the inspection of aerial fixed wing and rotary aircraft spray systems for agriculture, forestry, turf, and vegetation control in transport access ways (such as gas and electric lines), with regard to minimizing the potential risk of environmental contamination during use. This document applies only to manned aerial aircraft. It does not cover aircraft safety and design criteria for air worthiness, aircraft registration, pilot or operator requirements, all of which are specified separately by countries or regions. This document relates mainly to the condition of the equipment with respect to its potential risk for the environment and its performance to achieve good applications. The general requirements of ISO 16122-1 apply where appropriate, including for the protection of inspectors during an inspection.
- Standard10 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
This document defines terms commonly used in relation to equipment for applying plant protection products for crop protection.
- Standard40 pagesEnglish languagesale 15% off
- Standard40 pagesEnglish languagesale 15% off
- Standard36 pagesFrench languagesale 15% off
- Standard36 pagesFrench languagesale 15% off
This document specifies test methods and the environmental conditions for evaluating the performance of reciprocating positive displacement pumps and centrifugal pumps designed for crop protection equipment. This document is applicable when defining the performance of stand-alone pumps or pumps that are installed on a sprayer. Some of the tests indicated in this document are suited only for specific pump types. It is not applicable to pesticide metering pumps for injection systems.
- Standard22 pagesEnglish languagesale 15% off
- Standard22 pagesEnglish languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
This document specifies safety requirements and their verification, environmental requirements and related test methods, and minimum performance limits, for the design and construction of knapsack combustion engine-driven airblast sprayers as defined in 3.9. It describes methods for the elimination or reduction of hazards arising from their use. In addition, it specifies the type of information on safe working practices to be provided by the manufacturer. It addresses general operating parameters as well as the potential deposition of spray droplets under specified controlled conditions. This document deals with all significant hazards, hazardous situations and events, excepting those arising from vibration transmitted to the back of the operator. It is applicable to knapsack combustion engine-driven airblast sprayers when they are used as intended and under the conditions foreseeable by the manufacturer (see Table A.1). It is not applicable to: — hydraulic pressure sprayers; — thermal sprayers; — cold foggers; — sprayers adapted for the application of dry material. It is not applicable to knapsack combustion engine-driven airblast sprayers manufactured before the date of its publication. The requirements of this document applies to products manufactured 18 months after publication.
- Standard39 pagesEnglish languagesale 15% off
- Standard41 pagesFrench languagesale 15% off
This document, intended to be used together with ISO 4254-1, specifies the safety requirements and their verification for the design and construction of portable agricultural grain augers. This document covers conventional and swing-away portable agricultural augers designed primarily for conveying agricultural materials on farms. This document does not deal with the design or safety aspects of: — drag augers; — bin sweeps; — other augers that do not have wheels suitable for towing. NOTE Examples of covered equipment are shown in Annex A. When provisions of this document are different from those which are stated in ISO 4254-1, the provisions of this document take precedence over the provisions of ISO 4254-1 for machines that have been designed and built according the provisions of this document This document, taken together with ISO 4254-1, deals with all the significant hazards (as listed in Table 1), hazardous situations and events relevant to portable agricultural grain augers, when they are used as intended and under the conditions foreseen by the manufacturer (see Annex B). This document is not applicable to machines manufactured before the date of its publication.
- Standard14 pagesEnglish languagesale 15% off
- Standard14 pagesEnglish languagesale 15% off
- Standard14 pagesFrench languagesale 15% off
- Standard14 pagesFrench languagesale 15% off
This document specifies the system of colour coding for flow rate identification of nozzles used on sprayers. It is applicable to hydraulic energy nozzles such as flat and cone nozzles used for the application of crop protection products. This document is not applicable to adjustable nozzles. It allows for flow recognition on small parts in order to avoid any confusion under normal conditions of use.
- Standard5 pagesEnglish languagesale 15% off
- Standard5 pagesEnglish languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
This document specifies procedures for classifying droplet size spectra from atomizers used in spraying for crop protection. It provides a reference system for defining classes of droplet size spectra. Depending on their function principle and individual setup, measuring systems for droplet sizing can give different results. This document provides a means of comparing measured droplet size spectra to reference spectra and enables relative comparisons of droplet size spectra obtained from different measuring systems.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
This document specifies the test method to assess the performance of volume/area adjustment systems
for spray systems.
This document is not applicable for manually-operated knapsack sprayers or for aircraft sprayers.
- Standard6 pagesEnglish languagesale 15% off
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard7 pagesFrench languagesale 15% off
This document is applicable for sprayers intended to apply liquid over a horizontal surface.
This document specifies test methods to assess sprayed liquid horizontal transverse distribution.
Methods are based on sprayed liquid volume measurement, nozzle flow rate measurement or nozzle tip
pressure measurement.
This document does not cover aerial sprayers.
Hydraulic sprayers use a range of design features to deliver and control spray. The test methods
provided in this document are all useful but don’t give the same information. They are complementary.
Some test methods are not suitable for all sprayer types. Applicable test methods are described in an
informative annex.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard10 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
ISO 5682-1:2017 specifies test methods to assess the performance of sprayer nozzles with the exception of droplet characteristics. Applicable tests by nozzle type are described in an informative annex as a guide, but this is not required for use of this document.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard35 pagesEnglish languagesale 15% off
- Standard35 pagesFrench languagesale 15% off
ISO 1401:2016 specifies requirements for three types of flexible rubber hose for pressure spraying of agricultural chemicals and/or fertilizer products within a temperature range of ?10 °C to +60 °C.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 5682-2:2017 is applicable for sprayers intended to apply liquid over a horizontal surface. ISO 5682-2:2017 specifies test methods to assess sprayed liquid horizontal transverse distribution. Methods are based on sprayed liquid volume measurement, nozzle flow rate measurement or nozzle tip pressure measurement. ISO 5682-2:2017 does not cover aerial sprayers. Hydraulic sprayers use a range of design features to deliver and control spray. The test methods provided in this document are all useful but don't give the same information. They are complementary. Some test methods are not suitable for all sprayer types. Applicable test methods are described in an informative annex.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard10 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
ISO 5682-1:2017 specifies test methods to assess the performance of sprayer nozzles with the exception of droplet characteristics. Applicable tests by nozzle type are described in an informative annex as a guide, but this is not required for use of this document.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard35 pagesEnglish languagesale 15% off
- Standard35 pagesFrench languagesale 15% off
ISO 5682-3:2017 specifies the test method to assess the performance of volume/area adjustment systems for spray systems. ISO 5682-3:2017 is not applicable for manually-operated knapsack sprayers or for aircraft sprayers.
- Standard6 pagesEnglish languagesale 15% off
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard7 pagesFrench languagesale 15% off
ISO 1401:2016 specifies requirements for three types of flexible rubber hose for pressure spraying of agricultural chemicals and/or fertilizer products within a temperature range of ?10 °C to +60 °C.
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
ISO 22401:2015 provides a test method to measure spray sedimentation from horizontal boom sprayers using a test bench. The sedimentation measure gives a value for potential spray drift. These measurements can be used to compare different sprayer setups on the same sprayer. ISO 22401:2015 is applicable to mounted, trailed and self-propelled horizontal boom sprayers used in arable crops; and horizontal boom sprayers used for weed control in orchards/vineyards and spray application on horticultural crops. ISO 22401:2015 is intended for booms using a uniform set of spray generators. If intended for spray drift classification of the sprayer, the comparison is limited to nozzle type, spray pressure and boom height. NOTE Further investigations and tests are on-going to consider other parameters for classification aims (e.g. air assisted system, forward speed, nozzle spacing and orientation).
- Standard12 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
ISO 16122-2:2015, when used together with ISO 16122-1, specifies the requirements and test methods for the inspection of horizontal boom sprayers, when in use. The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve good application. Requirements for the protection of inspectors during an inspection are given in ISO 16122 1.
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 16122-3:2015, when used together with ISO 16122-1, specifies the requirements and test methods for the inspection of sprayers for bushes and trees, when in use. The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve a good application. Requirements for the protection of inspectors during an inspection are given in ISO 16122-1.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 16122-1:2015 defines the general requirements to be fulfilled for the inspection of all types of sprayers for plant protection products used in agriculture, horticulture, forestry and other areas, except knapsack sprayers (see ISO 19932?1 and ISO 19932?2).
The specific requirements for the different types of sprayers are defined in the relevant specific parts of ISO 16122. When used in conjunction with the relevant sprayer specific part, ISO 16122-1:2015 specifies the requirements and test methods for the in use inspection of sprayers. The requirements relate mainly to the condition of the sprayer with respect to potential risks for the environment and its performance to achieve a good application.
ISO 16122-1:2015 also includes minimum requirements for the preparation of the sprayer for the inspection and the minimum safety requirements with respect to the safety of the inspector (test operator) during the inspection.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 16122-4:2015, when used together with ISO 16122‑1, specifies the requirements and test methods for the inspection of fixed and semi-mobile sprayers, when in use.
The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve good application.
It does not apply to application equipment for spatial treatment (e.g. foggers).
Note that requirements for the protection of inspectors during an inspection are given in ISO 16122‑1.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 16119-4:2014 specifies requirements and the means for their verification for the design and performance of fixed and semi-mobile sprayers, as defined in 3.1 and 3.2, with regard to minimizing the potential risk of environmental contamination during use, including misuse foreseeable by the manufacturer.
This type of spraying system is generally a combination of separate elements (main tank, pump and application unit) that can be assembled in fixed installations (fixed sprayers) or with moving parts (semi-mobile sprayers).
ISO 16119-4:2014 does not apply to application equipment for space/spatial treatments.
ISO 16119-4:2014 is intended to be used with ISO 16119‑1, which gives general requirements common to all the sprayer types covered by ISO 16119. When requirements of ISO 16119-4:2014 are different from those stated in ISO 16119‑1, the requirements of ISO 16119-4:2014 take precedence over the requirements of ISO 16119‑1 for machines within the scope of ISO 16119-4:2014. ISO 16119-4:2014 does not cover safety aspects (see ISO 4254‑6).
ISO 16119-4:2014 is not applicable to sprayers manufactured before the date of its publication.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard applies to all types of machinery for pesticide application applicators used in agriculture, horticulture, forestry and other areas. ISO 16122 specifies the requirements and test methods for the inspection of machines in use. It relates mainly to the condition of the machine with respect to its potential risk for the environment and its performance to achieve a good application. This part of ISO 16122 defines the general requirements to be fulfilled. The specific requirements to the different types of machines are defined in the relevant specific parts. The scope of each specific part is defined in Annex A, normative. It also includes minimum safety requirements dealing with the operator’s safety during inspection.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements and methods of their verification for the inspection of air-assisted sprayers for bush and tree crops in use. It relates mainly to the condition of the sprayer in respect of safety hazards for the test operator, the potential risk of environmental contamination and opportunities to achieve good application.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements and methods of their verification for the inspection of field crop sprayers in use. It relates mainly to the condition of the sprayer in respect of safety hazards for the test operator, the potential risk of environmental contamination and opportunities to achieve good application.
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard, to be used with ISO 16122-1, specifies the requirements and methods for their verification for the inspection of fixed and semi-mobile prayers in use. It relates mainly to the condition of the sprayer in respect of the potential risk of environmental contamination and opportunities to achieve good application.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 24253-2:2015 specifies a method for field measurements to determine the quantity and distribution of spray in a field crop, treated by horizontal boom sprayers with downward directed application. It can be used for nursery trees and small size bush crops (young currants) when sprayed with boom sprayers. NOTE When interested in the spray deposition over width of the crop canopy, it is advised to use ISO 22522. ISO 24253-2:2015 allows flexibility in the arrangement of field tests, but specifies standardized measurement procedures that are useful to be able to compare the results from different field experiments or to compare with laboratory tests, such as that specified in ISO 5682-2. ISO 24253 is not intended for use in or for a regulatory framework.
- Standard21 pagesEnglish languagesale 15% off
- Standard21 pagesEnglish languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
ISO 24253-1:2015 specifies field measurements of spray deposition to determine the quantity and distribution of spray in a plane surface area, treated by horizontal boom sprayers with downward directed application. ISO 24253-1:2015 allows flexibility in the arrangement of field tests, but specifies standardized measurement procedures that are useful to be able to compare the results from different field experiments or to compare with laboratory tests, such as that described in ISO 5682‑2. ISO 24253-1:2015 may not be appropriate for those spraying systems which rely on the presence of a crop canopy for efficient deposition (for example directed spraying, electrostatic charged spraying, very fine spraying, variable rate spraying). ISO 24253 is not intended for use in or for a regulatory framework.
- Standard19 pagesEnglish languagesale 15% off
- Standard19 pagesFrench languagesale 15% off
ISO 16122-2:2015, when used together with ISO 16122-1, specifies the requirements and test methods for the inspection of horizontal boom sprayers, when in use. The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve good application. Requirements for the protection of inspectors during an inspection are given in ISO 16122 1.
- Standard18 pagesEnglish languagesale 15% off
- Standard19 pagesFrench languagesale 15% off
ISO 16122-4:2015, when used together with ISO 16122‑1, specifies the requirements and test methods for the inspection of fixed and semi-mobile sprayers, when in use. The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve good application. It does not apply to application equipment for spatial treatment (e.g. foggers). Note that requirements for the protection of inspectors during an inspection are given in ISO 16122‑1.
- Standard19 pagesEnglish languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
ISO 16122-3:2015, when used together with ISO 16122-1, specifies the requirements and test methods for the inspection of sprayers for bushes and trees, when in use. The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve a good application. Requirements for the protection of inspectors during an inspection are given in ISO 16122-1.
- Standard15 pagesEnglish languagesale 15% off
- Standard16 pagesFrench languagesale 15% off