ISO 11452-7:2003/Amd 1:2013

Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 7: Direct radio frequency (RF) power injection — Amendment 1

Véhicules routiers — Méthodes d'essai d'un équipement soumis à des perturbations électriques par rayonnement d'énergie électromagnétique en bande étroite — Partie 7: Injection directe de puissance aux fréquences radioélectriques (RF) — Amendement 1

General Information

• Status: Published
• Publication Date: 11-Jun-2013
• ICS: 33.100.20 - Immunity
• ICS: 43.040.10 - Electrical and electronic equipment
• Technical Committee: ISO/TC 22/SC 32 - Electrical and electronic components and general system aspects
• Drafting Committee: ISO/TC 22/SC 32/WG 3 - Electromagnetic compatibility
• Current Stage: 6060 - International Standard published
• Due Date: 29-Mar-2015
• Completion Date: 12-Jun-2013

Relations

• Amends: ISO 11452-7:2003 - Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 7: Direct radio frequency (RF) power injection
• Effective Date: 14-Oct-2020

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 11452-7
Second edition
2003-11-15
AMENDMENT 1
2013-06-15
Road vehicles — Component test
methods for electrial disturbances
from narrowband radiated
electromagnetic energy —
Part 7:
Direct radio frequency (RF) power
injection
AMENDMENT 1
Véhicules routiers — Méthodes d’essai d’un équipement soumis
à des perturbations électriques par rayonnement d’énergie
électromagnétique en bande étroite — Partie 7: Injection directe de
puissance aux fréquences radioélectriques (RF) — AMENDEMENT 1
Reference number
ISO 11452-7:2003/Amd.1:2013(E)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 11452-7:2003/Amd.1:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 11452-7:2003/Amd.1:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduct
...