ISO 13232-1:2005/Amd 1:2012

Motorcycles — Test and analysis procedures for research evaluation of rider crash protective devices fitted to motorcycles — Part 1: Definitions, symbols and general considerations — Amendment 1: MATD test helmet, ground impact, and injury costs

Motocycles — Méthodes d'essai et d'analyse de l'évaluation par la recherche des dispositifs, montés sur les motocycles, visant à la protection des motocyclistes contre les collisions — Partie 1: Définitions, symboles et généralités — Amendement 1: Casque d'essai MATD, impact au sol et coûts des blessures

General Information

• Status: Published
• Publication Date: 11-Jul-2012
• ICS: 43.140 - Motorcycles and mopeds
• Technical Committee: ISO/TC 22/SC 38 - Motorcycles and mopeds
• Drafting Committee: ISO/TC 22/SC 38 - Motorcycles and mopeds
• Current Stage: 6060 - International Standard published
• Due Date: 13-Aug-2013
• Completion Date: 12-Jul-2012

Relations

• Amends: ISO 13232-1:2005 - Motorcycles — Test and analysis procedures for research evaluation of rider crash protective devices fitted to motorcycles — Part 1: Definitions, symbols and general considerations
• Effective Date: 08-May-2020

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 13232-1
Second edition
2005-12-15
AMENDMENT 1
2012-07-15
Motorcycles — Test and analysis
procedures for research evaluation of
rider crash protective devices fitted to
motorcycles —
Part 1:
Definitions, symbols and general
considerations
Amendment 1: MATD test helmet, ground
impact, and injury costs
Motocycles — Méthodes d’essai et d’analyse de l’évaluation par la
recherche des dispositifs, montés sur les motocycles, visant à la
protection des motocyclistes contre les collisions —
Partie 1: Définitions, symboles et généralités
Amendement 1: Casque d’essai MATD, impact au sol et coûts
Reference number
ISO 13232-1:2005/Amd.1:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 13232-1:2005/Amd.1:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 13232-1:2005/Amd.1:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1
...