ISO 18639-4:2018/Amd 1:2023
(Amendment)PPE ensembles for firefighters undertaking specific rescue activities — Part 4: Gloves — Amendment 1
PPE ensembles for firefighters undertaking specific rescue activities — Part 4: Gloves — Amendment 1
Équipements de protection personnelle pour pompiers entreprenant des activités de sauvetage particulières — Partie 4: Gants — Amendement 1
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 18639-4
First edition
2018-11
AMENDMENT 1
2023-03
PPE ensembles for firefighters
undertaking specific rescue
activities —
Part 4:
Gloves
AMENDMENT 1
Équipements de protection personnelle pour pompiers entreprenant
des activités de sauvetage particulières —
Partie 4: Gants
AMENDEMENT 1
Reference number
ISO 18639-4:2018/Amd.1:2023(E)
© ISO 2023
---------------------- Page: 1 ----------------------
ISO 18639-4:2018/Amd.1:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 18639-4:2018/Amd.1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 94, Personal safety — Personal protective
equipment, Subcommittee SC 14, Firefighters' personal equipment.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iii
© ISO 2023 – All rights reserved
---------------------- Page: 3 ----------------------
ISO 18639-4:2018/Amd.1:2023(E)
PPE ensembles for firefighters undertaking specific rescue
activities —
Part 4:
Gloves
AMENDMENT 1
Normative references
Add the following International Standard:
ISO 23388:2018, Protective gloves against mechanical risks
6.2. Table 1
The requirements for liquid penetration resistance (optional) were changed as follows:
Road traffic crash Urban search and rescue
Requirements
(RTC) (USAR)
Liquid penetration resistance No penetration of any liquid f
...
AMENDMENT
Style Definition: Heading 1: Indent: Left: 0 pt, First
line: 0 pt, Tab stops: Not at 21.6 pt
ISO 18639-4:2018 FDAM 1:2022(E)
Style Definition: Heading 2: Font: Bold, Tab stops: Not
at 18 pt
ISO/TC 94/SC 14
Style Definition: Heading 3: Font: Bold
Style Definition: Heading 4: Font: Bold
Date: 2022-11-14xx
Style Definition: Heading 5: Font: Bold
Secretariat: SA
Style Definition: Heading 6: Font: Bold
Style Definition: ANNEX
Style Definition: AMEND Terms Heading: Font: Bold
PPE ensembles for firefighters undertaking specific rescue activities — Part 4: Gloves —
Style Definition: AMEND Heading 1 Unnumbered:
AMENDMENT 1
Font: Bold
Style Definition: List Bullet: Indent: Left: 0 pt, Hanging:
Équipements de protection personnelle pour pompiers entreprenant des activités de sauvetage
18 pt, No bullets or numbering, Tab stops: 18 pt, List
particulières — Partie 4: Gants — Amendement 1
tab
Style Definition: List Bullet 2: Indent: Left: 14.15 pt,
Hanging: 18 pt, No bullets or numbering, Tab stops:
32.15 pt, List tab
Style Definition: List Bullet 3: Indent: Left: 28.3 pt,
Hanging: 18 pt, No bullets or numbering, Tab stops:
46.3 pt, List tab
Style Definition: List Bullet 4: Indent: Left: 42.45 pt,
Hanging: 18 pt, No bullets or numbering, Tab stops:
60.45 pt, List tab
Style Definition: List Bullet 5: Indent: Left: 56.6 pt,
Hanging: 18 pt, No bullets or numbering, Tab stops:
74.6 pt, List tab
Style Definition: List Number: Indent: Left: 0 pt,
Hanging: 18 pt, No bullets or numbering, Tab stops:
18 pt, List tab
Style Definition: List Number 5: Indent: Left: 56.6 pt,
Hanging: 18 pt, No bullets or numbering, Tab stops:
74.6 pt, List tab
---------------------- Page: 1 ----------------------
ISO 18639-4:2018/FDAM 1:2022(E)
© ISO 2022
Formatted: Pattern: Clear
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part Formatted: Pattern: Clear
of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or
mechanical, including photocopying, or posting on the internet or an intranet, without prior written
permission. Permission can be requested from either ISO at the address below or ISO’s member body
in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.orgwww.iso.org
Published in Switzerland
ii © ISO 2022 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 18639-4:2018/FDAM 1:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical com-
mittee has been established has the right to be represented on that committee. International organiza-
tions, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collabo-
rates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical
standardization.
The procedures used to develop this document and those intended for its further maintenance are de-
scribed in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the dif-
ferent types of ISO documents should be noted. This document was drafted in accordance with the edito-
rial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directiveswww.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patentswww.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assess-
ment, as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in
the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/fore-
word.htmlwww.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 94, Personal safety — Protective clothing
and equipment, Subcommittee SC 14, Fire-fighters' personal equipment.
© ISO 2022 – All rights reserved iii
---------------------- Page: 3 --
...
FINAL
AMENDMENT ISO
DRAFT
18639-
4:2018
FDAM 1
ISO/TC 94/SC 14
PPE ensembles for firefighters
Secretariat: SA
undertaking specific rescue
Voting begins on:
2022-12-15 activities —
Voting terminates on:
Part 4:
2023-02-09
Gloves
AMENDMENT 1
Équipements de protection personnelle pour pompiers entreprenant
des activités de sauvetage particulières —
Partie 4: Gants
AMENDEMENT 1
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO 18639-4:2018/FDAM 1:2022(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2022
---------------------- Page: 1 ----------------------
ISO 18639-4:2018/FDAM 1:2022(E)
FINAL
AMENDMENT ISO
DRAFT
18639-
4:2018
FDAM 1
ISO/TC 94/SC 14
PPE ensembles for firefighters
Secretariat: SA
undertaking specific rescue
Voting begins on:
activities —
Voting terminates on:
Part 4:
Gloves
AMENDMENT 1
Équipements de protection personnelle pour pompiers entreprenant
des activités de sauvetage particulières —
Partie 4: Gants
AMENDEMENT 1
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: +41 22 749 01 11
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: copyright@iso.org
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO 18639-4:2018/FDAM 1:2022(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
© ISO 2022 – All rights reserved
NATIONAL REGULATIONS. © ISO 2022
---------------------- Page: 2 ----------------------
ISO 18639-4:2018/FDAM 1:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 94
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.