SIST EN 4710-003:2015
(Main)Aerospace series - Quick release fastening systems for non-structural applications - Part 003: Spring clamp
Aerospace series - Quick release fastening systems for non-structural applications - Part 003: Spring clamp
This standard specifies the dimensions, mass, tolerances and static values of catch spring for use in
fuselage interior equipment and non-structural or secondary structural area. This standard part shall be
used in conjunction with EN 4710-06 and EN 4710-07 as described in EN 4710-02.
The applicable temperature range is −55 °C to 85 °C.
Luft- und Raumfahrt - Druckverschlüsse nicht-strukturelle Anwendungen - Teil 003: Feder Clip
Série aérospatiale - Fixations rapides filetées pour applications non-structurales - Partie 003: Collier lyre
Aeronavtika - Spončni sistemi za hitro sprostitev za nestrukturne aplikacije - 003. del: Vzmetna objemka
Ta standard določa dimenzije, maso, tolerance in statične vrednosti natezne vzmeti za uporabo v notranji opremi v trupu letala ter nestrukturnem ali sekundarnem strukturnem območju. Ta del standarda se uporablja v povezavi s standardoma EN 4710-06 in EN 4710-07, kot je opisano v standardu EN 4710-02. Delovna temperatura je med –55 °C in 85 °C.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Druckverschlüsse nicht-strukturelle Anwendungen - Teil 003: Feder ClipSérie aérospatiale - Fixations rapides filetées pour applications non-structurales - Partie 003: Collier lyreAerospace series - Quick release fastening systems for non-structural applications - Part 003: Spring clamp49.030.01Vezni elementi na splošnoFasteners in generalICS:Ta slovenski standard je istoveten z:EN 4710-03:2015SIST EN 4710-003:2015en,fr,de01-december-2015SIST EN 4710-003:2015SLOVENSKI
STANDARD
SIST EN 4710-003:2015
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4710-03
October
t r s w ICS
v {ä r u w English Version
Aerospace series æ Quick release fastening systems for nonæstructural applications æ Part
r uã Spring clamp Série aérospatiale æ Fixations rapides filetées pour applications nonæstructurales æ Partie
r uã Collier lyre
Luftæ und Raumfahrt æ Druckverschlüsse nichtæstrukturelle Anwendungen æ Teil
r uã Federclip This European Standard was approved by CEN on
w March
t r s wä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s w CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
v y s ræ r uã t r s w ESIST EN 4710-003:2015
EN 4710-03:2015 (E) 2 Contents
Page European foreword .3 1 Scope .4 2 Normative references .4 3 Requirements.4 4 Designation .7 5 Marking .7 6 Technical specification .7
SIST EN 4710-003:2015
EN 4710-03:2015 (E) 3 European foreword This document (EN 4710-03:2015) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2016, and conflicting national standards shall be withdrawn at the latest by April 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slov
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.