iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 60534-8-1:2001

(Main)

Industrial-process control valves -- Part 8: Noise considerations -- Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves

Industrial-process control valves -- Part 8: Noise considerations -- Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves

Defines equipment, methods and procedures for obtaining laboratory measurements of airborne sound-pressure levels radiated by control valves and/or associated piping configurations, including fixed restrictions, through which compressible fluids are passing. Provides a method of testing the noise-generating characteristics of control valves. The noise characteristics to be determined are useful for comparing the performance of different valves and planning measures for noise abatement.

Stellventile für die Prozeßregelung -- Teil 8: Geräuschbetrachtungen -- Hauptabschnitt 1: Laboratoriummessungen von Geräuschen bei gasdurchströmten Stellventilen

Vannes de régulation des processus industriels -- Partie 8: Considérations sur le bruit -- Section 1: Mesure en laboratoire du bruit créé par un débit aérodynamique à travers une vanne de régulation

Définit le matériel, les méthodes et les procédures pour obtenir des mesures en laboratoire des niveaux de pression acoustique aérienne rayonnée par les vannes régulation et/ou les configurations de tuyauteries associées, à travers lesquelles passent des fluides compressibles. Fournit une méthode d'essai des caractéristiques génératrices de bruit d'une vanne de régulation. Une méthode unifiée de mesure de bruit généré par la vanne et les tuyauteries d'essai associées permet une comparaison des différents résultats de mesure, qui est bénéfique à la fois à l'utilisateur et au fabricant. Les critères de bruit sont exprimés en déterminant le niveau de pression acoustique (NPA) de la vanne considérée. Les caractéristiques de bruit à déterminer sont utiles pour comparer le fonctionnement de différentes vannes, et prendre les dispositions pour atténuer le bruit.

Industrial-process control valves - Part 8: Noise considerations - Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves (IEC 60534 -8-1:1986)

General Information

Status
Withdrawn
Publication Date
31-Mar-2001
Withdrawal Date
31-Dec-2006
ICS
17.140.20 - Noise emitted by machines and equipment
23.060.40 - Pressure regulators
25.040.40 - Industrial process measurement and control
Technical Committee
MKP - Industrial-process measurement and control
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Jan-2007
Due Date
01-Jan-2007
Completion Date
01-Jan-2007
Ref Project
EN 60534-8-1:2000 - Industrial-process control valves - Part 8: Noise considerations - Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves

Relations

Replaced By
SIST EN 60534-8-1:2007 - Industrial-process control valves -- Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves
Effective Date
06-May-2014
Replaced By
SIST EN 60534-8-1:2007 - Industrial-process control valves -- Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves
Effective Date
29-Jan-2023

Buy Standard

EN 60534-8-1:2001EN 60534-8-1:2001
PreviousNext
Standard
EN 60534-8-1:2001
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60534-8-1:2001
01-april-2001
Industrial-process control valves - Part 8: Noise considerations - Section 1:
Laboratory measurement of noise generated by aerodynamic flow through control
valves (IEC 60534 -8-1:1986)
Industrial-process control valves -- Part 8: Noise considerations -- Section 1: Laboratory
measurement of noise generated by aerodynamic flow through control valves
Stellventile für die Prozeßregelung -- Teil 8: Geräuschbetrachtungen -- Hauptabschnitt 1:
Laboratoriummessungen von Geräuschen bei gasdurchströmten Stellventilen
Vannes de régulation des processus industriels -- Partie 8: Considérations sur le bruit --
Section 1: Mesure en laboratoire du bruit créé par un débit aérodynamique à travers une
vanne de régulation
Ta slovenski standard je istoveten z: EN 60534-8-1:2000
ICS:
17.140.20 Emisija hrupa naprav in Noise emitted by machines
opreme and equipment
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
SIST EN 60534-8-1:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ---------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 60534-8-1:2007(Main)
Industrial-process control valves -- Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves
EN 60534-8-1:2005

This part of IEC 60534-8 defines equipment, methods, and procedures for obtaining laboratory measurements of sound pressure levels radiated by control valves and/or associated piping configurations, including fixed restrictions, through which compressible fluids are passing. Control valves discharging to atmosphere are excluded from this standard. Method A is a uniform method of measuring the radiated noise from the valve and associated test piping and allows a comparison of various measuring results which is beneficial for both user and manufacturer. The noise criteria are expressed by determining the sound pressure level of the valve under consideration. Method B is a procedure for measuring the sound pressure levels within pipe systems upstream and downstream of the valve under fixed operating conditions. Since inaccuracies due to the pipe transmission are eliminated, this method is preferred for evaluation of the acoustical characteristic of valves. The noise characteristics to be determined are useful for the following reasons: a) to compare the performance of different valves; b) to plan measures for noise abatement; c) to determine acoustical characteristics of valves and valve assemblies; d) to enable proper sizing of sound absorbers; e) to determine possible adverse effects on ultra-sonic flow meter measurements.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-8-4:2016(Main)
Industrial-process control valves - Part 8-4: Noise considerations - Prediction of noise generated by hydrodynamic flow (IEC 60534-8-4:2015)
EN 60534-8-4:2015

This part of IEC 60534 establishes a method to predict the noise generated in a control valve
by liquid flow and the resulting noise level measured downstream of the valve and outside of
the pipe. The noise may be generated both by normal turbulence and by liquid cavitation in
the valve. Parts of the method are based on fundamental principles of acoustics, fluid
mechanics, and mechanics. The method is validated by test data.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-8-2:2012(Main)
Industrial-process control valves - Part 8-2: Noise considerations - Laboratory measurement of noise generated by hydrodynamic flow through control valves (IEC 60534-8-2:2011)
EN 60534-8-2:2011

This part of IEC 60534-8 includes the method for measuring the sound pressure level due to liquid flow through a control valve and the method for determining the characteristic increase of noise due to the onset of cavitation. It also defines the equipment, methods and procedures for the laboratory measurement of the airborne sound needed to determine these characteristics. Two methods are provided for testing the noise generating characteristics of control valves. The first is a uniform method of measuring the radiated noise from the valve and the associated test piping including fixed flow restrictions through which the test fluid (water) is
passing (see Note 1). The noise criteria are expressed by determining the sound pressure level of the valve under consideration. The second is a procedure for measuring the sound pressure levels within pipe systems upstream and downstream of the valve under fixed operating conditions. Since inaccuracies due to the pipe transmission are eliminated, this method shall be preferred for evaluation of the acoustical characteristic of valves. The noise characteristics to be determined are useful:
a) to determine acoustical characteristics of valves and valve assemblies and the characteristic pressure ratio factor xFz of a control valve;
b) to predict valve noise for given process conditions;
c) to compare the performance of different valves and various measuring results;
d) to plan measures for increasing service life and noise abatement;
e) to determine possible adverse effects on ultra-sonic flow meter measurements;
f) to enable proper sizing of sound absorbers.
NOTE 1 Test fluids other than water or valves without downstream piping are not within the scope of this section of IEC 60534-8.
NOTE 2 The factor xFz is used in a noise prediction method which is covered in IEC 60534-8-4.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-8-3:2011(Main)
Industrial-process control valves - Part 8-3: Noise considerations - Control valve aerodynamic noise prediction method (IEC 60534-8-3:2010)
EN 60534-8-3:2011

This Standard establishes a theoretical method to predict the external sound-pressure level generated in a control valve and within adjacent pipe expanders by the flow of compressible fluids. This method considers only single-phase dry gases and vapours and is based on the perfect gas laws. It is assumed that the downstream piping is straight for a length of at least 2 m from the point where the noise measurement is made. The method is applicable to the following single-stage valves: - globe (straight pattern and angle pattern), - butterfly, - rotary plug (eccentric, spherical), - ball, and - valves with cage trims. Specifically excluded are the full bore ball valves where the product FpC exceeds 50 % of the rated flow coefficient. This third edition cancels and replaces the second edition published in 2000. This edition constitutes a technical revision. The significant technical changes with respect to the previous edition are as follows: - predicting noise as a function of frequency; - using laboratory data to determine the acoustical efficiency factor.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-8-1:2007(Main)
Industrial-process control valves -- Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves
EN 60534-8-1:2005

This part of IEC 60534-8 defines equipment, methods, and procedures for obtaining laboratory measurements of sound pressure levels radiated by control valves and/or associated piping configurations, including fixed restrictions, through which compressible fluids are passing. Control valves discharging to atmosphere are excluded from this standard. Method A is a uniform method of measuring the radiated noise from the valve and associated test piping and allows a comparison of various measuring results which is beneficial for both user and manufacturer. The noise criteria are expressed by determining the sound pressure level of the valve under consideration. Method B is a procedure for measuring the sound pressure levels within pipe systems upstream and downstream of the valve under fixed operating conditions. Since inaccuracies due to the pipe transmission are eliminated, this method is preferred for evaluation of the acoustical characteristic of valves. The noise characteristics to be determined are useful for the following reasons: a) to compare the performance of different valves; b) to plan measures for noise abatement; c) to determine acoustical characteristics of valves and valve assemblies; d) to enable proper sizing of sound absorbers; e) to determine possible adverse effects on ultra-sonic flow meter measurements.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 12349:2023(Main)
Mechanical vibration - Guide to the health effects of vibration on the human body
CEN/TR 12349:2023

The aim of this CEN report is to provide information on the possible adverse health effects caused by exposure to vibration at work.  the report addresses manufacturers as well as employers and employees using vibrating machinery in order to improve their understanding of the possible health problems arising from occupational exposure to vibration.

  • Technical report
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 80004-1:2023(Main)
Nanotechnologies - Vocabulary - Part 1: Core vocabulary (ISO 80004-1:2023)
EN ISO 80004-1:2023

This document defines core terms in the field of nanotechnology. This document is intended to facilitate communication between organizations and individuals in industry and those who interact with them.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3262-4:2023(Main)
Extenders - Specifications and methods of test - Part 4: Whiting (ISO 3262-4:2022)
EN ISO 3262-4:2023

This document specifies requirements and corresponding methods of test for whiting.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 1247-1:2023(Main)
Aluminium pigments for paints - Part 1: General aluminium pigments (ISO 1247-1:2021)
EN ISO 1247-1:2023

This document specifies the requirements and corresponding test methods for aluminium pigments suitable for use in paints including:
a) general, decorative and protective paints, and
b) special finishing paints.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 18473-4:2023(Main)
Functional pigments and extenders for special applications - Part 4: Nanoscale titanium dioxide for photocatalytic application (ISO 18473-4:2022)
EN ISO 18473-4:2023

This document specifies requirements and corresponding test methods for nanoscale titanium dioxide (TiO2) in either powder or suspension form for photocatalytic application.
This document is applicable to modified nanoscale titanium dioxide for photocatalytic application. Such modification can be surface treatment, coating, doping and combination thereof.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day