SIST EN ISO 22637:2019
(Main)Adhesives - Test of adhesive for floor covering - Determination of the electrical resistance of adhesive films and composites (ISO 22637:2019)
Adhesives - Test of adhesive for floor covering - Determination of the electrical resistance of adhesive films and composites (ISO 22637:2019)
This European Standard specifies a test method to measure the electrical resistance as a material physical parameter of an adhesive film and composites of floor covering material and adhesive film. The electrical resistance is reciprocal to the electrical conductivity. This laboratory method does not take account of all influences which may occur in practice.
In contrast to EN 1081, which applies to the determination of the electrical resistance of resilient floor coverings R1, R2 and R3 (see Clause 3), this method applies to the determination of the electrical resistance of adhesive films on glass respectively composites of floor coverings adhesively bonded to a fibre cement substrate R4 and R5 (see Clause 3).
Klebstoffe - Prüfung von Klebstoffen für Bodenbeläge - Bestimmung des elektrischen Widerstandes von Klebstoff-Filmen und Verbunden (ISO 22637:2019)
Dieses Dokument legt ein Prüfverfahren zur Messung des elektrischen Widerstandes als werkstoff-physikalischen Parameter eines Klebstoff-Films und von Verbunden aus einem Bodenbelag und einem Klebstoff-Film fest. Der elektrische Widerstand ist der Kehrwert der elektrischen Leitfähigkeit. Bei diesem Laborverfahren werden nicht alle Einflüsse, die in der Praxis vorkommen können, berücksichtigt.
Dieses Verfahren wird zur Bestimmung des elektrischen Widerstandes von Klebstoff-Filmen auf Glas und von Verbunden von auf einen Faserzementträger geklebten Bodenbelägen R4 und R5 (siehe Abschnitt 3) angewendet.
Adhésifs - Essai des adhésifs pour revêtements de sol - Détermination de la résistance électrique des composites et films d'adhésif (ISO 22637:2019)
Le présent document spécifie une méthode d'essai pour mesurer la résistance électrique en tant que paramètre physique d'un film adhésif et de composites de matériau de revêtement de sol et de film adhésif. La résistance électrique est l'inverse de la conductivité électrique. La présente méthode de laboratoire ne tient pas compte de toutes les influences pouvant survenir en pratique.
La présente méthode s'applique à la détermination de la résistance électrique des films adhésifs sur le verre et des composites de revêtements de sol collés sur un support en ciment renforcé de fibres R4 et R5 (voir l'Article 3).
Lepila - Preskusna metoda za lepila za talne obloge - Določanje električne upornosti lepilnih filmov in kompozitov (ISO 22637:2019)
Ta evropski standard določa preskusno metodo za merjenje električne upornosti kot bistvenega fizikalnega parametra lepilnega filma in sestavkov v materialu za talne obloge in lepilnem filmu. Električna upornost je lastnost, obratna od električne prevodnosti. Ta laboratorijska metoda ne upošteva vseh vplivov, ki se lahko pojavijo v praksi.
V nasprotju s standardom EN 1081, ki se uporablja za ugotavljanje električne upornosti pri netekstilnih talnih oblogah R1, R2 in R3 (glej točko 3), se ta metoda uporablja za ugotavljanje električne upornosti lepilnih filmov na steklu oziroma sestavkov v talnih oblogah, zlepljenih na podlago iz vlaknastega cementa R4 in R5 (glej točko 3).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 22637:2019
01-oktober-2019
Nadomešča:
SIST EN 13415:2010
Lepila - Preskusna metoda za lepila za talne obloge - Določanje električne
upornosti lepilnih filmov in kompozitov (ISO 22637:2019)
Adhesives - Test of adhesive for floor covering - Determination of the electrical resistance
of adhesive films and composites (ISO 22637:2019)
Klebstoffe - Prüfung von Klebstoffen für Bodenbeläge - Bestimmung des elektrischen
Widerstandes von Klebstoff-Filmen und Verbunden (ISO 22637:2019)
Adhésifs - Essai des adhésifs pour revêtements de sol - Détermination de la résistance
électrique des composites et films d'adhésif (ISO 22637:2019)
Ta slovenski standard je istoveten z: EN ISO 22637:2019
ICS:
83.180 Lepila Adhesives
SIST EN ISO 22637:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 22637:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 22637:2019
EN ISO 22637
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2019
EUROPÄISCHE NORM
ICS 83.180 Supersedes EN 13415:2010
English Version
Adhesives - Test of adhesive for floor covering -
Determination of the electrical resistance of adhesive films
and composites (ISO 22637:2019)
Adhésifs - Essai des adhésifs pour revêtements de sol - Klebstoffe - Prüfung von Klebstoffen für Bodenbeläge -
Détermination de la résistance électrique des Bestimmung des elektrischen Widerstandes von
composites et films d'adhésif (ISO 22637:2019) Klebstoff-Filmen und Verbunden (ISO 22637:2019)
This European Standard was approved by CEN on 8 September 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22637:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 22637:2019
EN ISO 22637:2019 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 22637:2019
EN ISO 22637:2019 (E)
European foreword
This document (EN ISO 22637:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 193 “Adhesives” the secretariat of which is held by
UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2020, and conflicting national standards shall
be withdrawn at the latest by January 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13415:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 22637:2019 has been approved by CEN as EN ISO 22637:2019 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 22637:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 22637:2019
INTERNATIONAL ISO
STANDARD 22637
First edition
2019-07
Adhesives — Test of adhesive for floor
covering — Determination of the
electrical resistance of adhesive films
and composites
Adhésifs — Essai des adhésifs pour revêtements de sol —
Détermination de la résistance électrique des composites et films
d'adhésif
Reference number
ISO 22637:2019(E)
©
ISO 2019
---------------------- Page: 7 ----------------------
SIST EN ISO 22637:2019
ISO 22637:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 22637:2019
ISO 22637:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Apparatus and materials. 2
5 Preparation of test specimens . 4
5.1 Preparation of test specimens for determination of adhesive resistance, R . 4
4
5.2 Preparation of test specimens for determination of vertical resistance of composite, R . 4
5
6 Storing the specimens . 5
6.1 Storing the specimens for determination of adhesive resistance, R . 5
4
6.2 Storing the specimens for determination of vertical resistance of composite R . 5
5
7 Test procedure . 6
7.1 General . 6
7.2 Adhesive resistances, R . 6
4
7.3 Vertical resistance of composite, R . 6
5
8 Test report . 6
© ISO 2019 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 22637:2019
ISO 22637:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Tech
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.