iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN ISO 4034:2013

(Main)

Hexagon regular nuts (style 1) - Product grade C (ISO 4034:2012)

Hexagon regular nuts (style 1) - Product grade C (ISO 4034:2012)

This International Standard specifies the characteristics of hexagon regular nuts (style 1) with threads from M5 up to and including M64 and product grade C. If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 898-2, ISO 965-1 and ISO 4759-1.

Sechskantmuttern (Typ 1) - Produktklasse C (ISO 4034:2012)

Diese Internationale Norm legt Eigenschaften von Sechskantmuttern (Typ 1) mit Gewinden von M5 bis M64 in Produktklasse C fest.
Falls in besonderen Fällen andere Festlegungen als die in dieser Internationalen Norm aufgeführten benötigt werden, können diese den entsprechenden Internationalen Normen entnommen werden, z. B. ISO 724, ISO 898-2, ISO 965-1 und ISO 4759-1.

Écrous hexagonaux normaux (style 1) - Grade C (ISO 4034:2012)

L'ISO 4034:2012 spécifie les caractéristiques des écrous hexagonaux de diamètre de filetage M5 à M64 inclus, de grade C.

Šestrobe matice (tip 1) - Razred izdelave C (ISO 4034:2012)

Ta mednarodni standard določa značilnosti šestrobih matic (tip 1) z navoji od M5 do vključno M64 in razredom izdelave C. Če so v posebnih primerih zahtevane specifikacije, ki niso navedene v tem mednarodnem standardu, jih je mogoče izbrati iz obstoječih mednarodnih standardov, na primer standardov ISO 724, ISO 898-2, ISO 965-1 in ISO 4759-1.

General Information

Status
Published
Publication Date
01-Apr-2013
ICS
21.060.20 - Nuts
Technical Committee
ISEL - Mechanical elements
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Mar-2013
Due Date
26-May-2013
Completion Date
02-Apr-2013
Ref Project
EN ISO 4034:2012 - Hexagon regular nuts (style 1) - Product grade C (ISO 4034:2012)

Relations

Revises
oSIST prEN ISO 4034:2016 - Hexagon regular nuts (style 1) - Product grade C (ISO/DIS 4034:2016)
Effective Date
18-Jan-2023
Revised
SIST EN ISO 4034:2002 - Hexagon nuts - Product grade C (ISO 4034:1999)
Effective Date
07-Mar-2012
Revises
oSIST prEN ISO 4034:2016 - Hexagon regular nuts (style 1) - Product grade C (ISO/DIS 4034:2016)
Effective Date
19-Jan-2023
Replaces
SIST EN ISO 4034:2002 - Hexagon nuts - Product grade C (ISO 4034:1999)
Effective Date
01-May-2013
Corrected By
SIST EN ISO 4034:2013/AC:2014 - Hexagon regular nuts (style 1) - Product grade C - Technical Corrigendum 1 (ISO 4034:2012/Cor 1:2013)
Effective Date
01-Jun-2014
Revised
oSIST prEN ISO 4034:2016 - Hexagon regular nuts (style 1) - Product grade C (ISO/DIS 4034:2016)
Effective Date
01-Jun-2016
Replaces
SIST EN ISO 4034:2002 - Hexagon nuts - Product grade C (ISO 4034:1999)
Effective Date
08-Jun-2022

Buy Standard

EN ISO 4034:2013EN ISO 4034:2013
PreviousNext
Standard
EN ISO 4034:2013
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 4034:2013
01-maj-2013
1DGRPHãþD
SIST EN ISO 4034:2002
Šestrobe matice (tip 1) - Razred izdelave C (ISO 4034:2012)
Hexagon regular nuts (style 1) - Product grade C (ISO 4034:2012)
Sechskantmuttern (Typ 1) - Produktklasse C (ISO 4034:2012)
Écrous hexagonaux normaux (style 1) - Grade C (ISO 4034:2012)
Ta slovenski standard je istoveten z: EN ISO 4034:2012
ICS:
21.060.20 Matice Nuts
SIST EN ISO 4034:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 4034:2013

---------------------- Page: 2 ----------------------

SIST EN ISO 4034:2013


EUROPEAN STANDARD
EN ISO 4034

NORME EUROPÉENNE

EUROPÄISCHE NORM
December 2012
ICS 21.060.20 Supersedes EN ISO 4034:2000
English Version
Hexagon regular nuts (style 1) - Product grade C (ISO
4034:2012)
Écrous hexagonaux normaux (style 1) - Grade C (ISO Sechskantmuttern - Produktklasse C (ISO 4034:2012)
4034:2012)
This European Standard was approved by CEN on 15 November 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4034:2012: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 4034:2013
EN ISO 4034:2012 (E)
Contents Page
Foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 4034:2013
EN ISO 4034:2012 (E)
Foreword
This document (EN ISO 4034:2012) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at
the latest by June 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4034:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 4034:2012 has been approved by CEN as a EN ISO 4034:2012 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 4034:2013

---------------------- Page: 6 ----------------------

SIST EN ISO 4034:2013
INTERNATIONAL ISO
STANDARD 4034
Fourth edition
2012-12-15
Hexagon regular nuts (style 1) —
Product grade C
Écrous hexagonaux normaux (style 1) — Grade C
Reference number
ISO 4034:2012(E)
©
ISO 2012

---------------------- Page: 7 ----------------------

SIST EN ISO 4034:2013
ISO 4034:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 4034:2013
ISO 4034:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Dimensions . 1
4 Requirements and reference International Standards . 3
5 Designation . 3
Bibliography . 4
© ISO 2012 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 4034:2013
ISO 4034:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4034 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 12, Fasteners with
metric internal thread.
This fourth edition cancels and replaces the third edition (ISO 4034:1999), of which it constitutes a minor revision.
iv © ISO 2012 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 4034:2013
ISO 4034:2012(E)
Introduction
This International Standard belongs to a complete group of product standards developed by ISO on external
hexagon drive fasteners. It comprise
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 898-2:2022(Main)
Fasteners - Mechanical properties of fasteners made of carbon steel and alloy steel - Part 2: Nuts with specified property classes (ISO 898-2:2022)
EN ISO 898-2:2022

This document specifies the mechanical and physical properties of nuts made of non-alloy steel or alloy
steel, when tested at the ambient temperature range of 10 °C to 35 °C.
This document applies to nuts:
— with ISO metric thread (see ISO 68-1),
— with diameter/pitch combinations according to ISO 261 and ISO 262,
— with coarse pitch thread M5 to M39, and fine pitch thread M8×1 to M39×3,
— with thread tolerances according to ISO 965-1, ISO 965-2 or ISO 965-5,
— with specified property classes 04, 05, 5, 6, 8, 10 and 12 including proof load,
— of three different nut styles (see 5.1): regular nuts (style 1), high nuts (style 2) and thin nuts (style 0),
— with a minimum outside diameter or width across flats s ≥ 1,45D,
— able to mate with bolts, screws and studs with property classes in accordance with ISO 898-1 (see
Annex B), and
— intended to be used in applications ranging from –50 °C to +150 °C, or up to +300 °C.
WARNING — Nuts conforming to the requirements of this document are tested at the ambient
temperature range of 10 °C to 35 °C and are used in applications ranging from –50 °C to +150 °C;
however, these nuts are also used outside this range and up to +300 °C for specific applications.
It is possible that they do not retain the specified mechanical and physical properties at lower
and/or elevated temperatures. Therefore, it is the responsibility of the user to determine the
appropriate choices based on the service environment conditions of the assembly (see also 7.1).
For additional specifications applicable to hot dip galvanized nuts, see ISO 10684.
For nuts designed for particular applications, see ISO/TR 16224.
This document does not specify requirements for functional properties such as:
— prevailing torque properties (see ISO 2320),
— torque/clamp force properties (see ISO 16047 for test method),
— weldability, or
— corrosion resistance.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3506-2:2020(Main)
Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts with specified grades and property classes (ISO 3506-2:2020)
EN ISO 3506-2:2020

This document specifies the mechanical and physical properties of nuts, with coarse pitch thread and
fine pitch thread, made of corrosion-resistant stainless steels, when tested at the ambient temperature
range of 10 °C to 35 °C. It specifies property classes in relation to austenitic, martensitic, ferritic and
duplex (austenitic-ferritic) steel grades for nuts.
ISO 3506-6 provides general rules and additional technical information on suitable stainless steels and
their properties.
Nuts conforming to the requirements of this document are evaluated at the ambient temperature
specified in paragraph 1. It is possible that they do not retain the specified mechanical and physical
properties at elevated and/or lower temperatures.
NOTE 1 Fasteners conforming to the requirements of this document are used without restriction in
applications ranging from –20 °C to +150 °C; however, fasteners conforming to this document are also used for
applications outside this range down to –196 °C and up to +300 °C. For more details, see ISO 3506-6.
Outside the temperature range of –20 °C to +150 °C, it is the responsibility of the user to determine the
appropriate choice for a given application, in consultation with an experienced fastener metallurgist
and by taking into account e.g. stainless steel composition, duration of exposure at elevated or low
temperature, the effect of the temperature on the fastener mechanical properties and clamped parts,
and the corrosive service environment of the bolted joint.
NOTE 2 ISO 3506-53) is developed in order to assist in the selection of appropriate stainless steel grades and
property classes intended for use at temperatures up to +800 °C.
This document applies to nuts:
— with ISO metric thread in accordance with ISO 68-1,
— with diameter/pitch combinations in accordance with ISO 261 and ISO 262,
— with coarse pitch thread M5 to M39, and fine pitch thread M8×1 to M39×3,
— with thread tolerances in accordance with ISO 965-1 and ISO 965-2,
— with specified property classes, including proof load,
— with different nut styles: thin nuts, regular nuts and high nuts,
— with a minimum nut height m ≥ 0,45D,
— with a minimum outside diameter or width across flats s ≥ 1,45D (see Annex A),
— of any shape, and
— able to mate with bolts, screws and studs with property classes in accordance with ISO 3506-1.
Stainless steel grades and property classes can be used for sizes outside the diameter limits of this
document (i.e. for D < 5 mm or D > 39 mm), provided that all applicable chemical, mechanical and
physical requirements are met.
This document does not specify requirements for functional properties such as:
— torque/clamp force properties,
— prevailing torque properties, or
— weldability.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14399-8:2018(Main)
High-strength structural bolting assemblies for preloading - Part 8: System HV - Hexagon fit bolt and nut assemblies
EN 14399-8:2018

This draft European Standard specifies together with EN 14399-1 and EN 14399-2, the requirements for assemblies of high-strength structural bolts and nuts of system HV suitable for preloaded joints with large widths across flats, thread sizes M12 to M36 and property classes 10.9/10.
Bolting assemblies (including fit bolts with nominal shank diameter d + 1 mm) in accordance with this document have been designed to allow preloading of at least 0,7 fub × As ) according to EN 1993-1-8 (Eurocode 3) and to obtain ductility predominantly by plastic deformation of the engaged threads. For this purpose the components have the following characteristics:
-   nut height approximately 0,8 d;
-   bolt with short thread length.
Bolting assemblies in accordance with this document include washers according to EN 14399-6.
NOTE   Attention is drawn to the importance of ensuring that the bolting assemblies are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made.
General requirements and requirements for suitability for preloading are specified in EN 14399-2.
Clamp lengths and grip lengths for the bolting assemblies are specified in the normative Annex A.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14399-7:2018(Main)
High-strength structural bolting assemblies for preloading - Part 7: System HR - Countersunk head bolt and nut assemblies
EN 14399-7:2018

This draft European Standard specifies, together with EN 14399-1 and EN 14399-2, the requirements for assemblies of high-strength structural countersunk bolts and nuts of system HR suitable for preloaded joints with thread sizes M12 to M36 and property classes 8.8/8 or 8.8/10 and 10.9/10.
Bolting assemblies in accordance with this document have been designed to allow preloading of at least 0,7 fub × As according to EN 1993-1-8 (Eurocode 3) and to obtain ductility predominantly by plastic elongation of the bolt. For this purpose the components have the following characteristics:
-   regular nut height according to (style 1) see EN ISO 4032;
-   thread length of the bolt according to ISO 888.
Bolting assemblies in accordance with this document include washers according to EN 14399-6 or to EN 14399-5.
NOTE   Attention is drawn to the importance of ensuring that bolting assemblies are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made.
General requirements and requirements for suitability for preloading are specified in EN 14399-2.
Clamp lengths and grip lengths for the bolting assemblies are specified in the normative Annex A.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14399-9:2018(Main)
High-strength structural bolting assemblies for preloading - Part 9: System HR or HV - Direct tension indicators for bolt and nut assemblies
EN 14399-9:2018

This draft European Standard specifies, together with EN 14399-1 and EN 14399-2, the requirements for compressible washer-type direct tension indicators, nut face washers and bolt face washers as part of high-strength structural bolting assemblies suitable for preloaded joints.
These direct tension indicators are specified as part of high-strength structural bolting assemblies of system HR or HV in accordance with EN 14399-3, EN 14399-4, EN 14399-7 or EN 14399-8, with nominal thread sizes M12 up to and including M36 and property classes 8.8/8 or 8.8/10 and 10.9/10.
It specifies two property designations H8 and H10 for direct tension indicators, together with general dimensions, tolerances, materials and performance.
Bolting assemblies in accordance with this document have been designed to allow preloading of at least 0,7 fub × As ) according to EN 1993-1-8 (Eurocode 3) and to obtain ductility predominantly by plastic elongation of the bolt for system HR in accordance with EN 14399-3 or EN 14399-7, or by plastic deformation of the engaged threads for system HV in accordance with EN 14399-4 or EN 14399-8.
Bolting assemblies conforming to this document may include washer(s) according to EN 14399-6 or to EN 14399-5 (under the nut only).
NOTE 1   Attention is drawn to the importance of ensuring that the bolting assemblies are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made.
General requirements and requirements for suitability for preloading are specified in EN 14399-2 together with Clause 5 of this document.
NOTE 2   Compressible washer-type direct tension indicators are also known as load indicating washers.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14399-10:2018(Main)
High-strength structural bolting assemblies for preloading - Part 10: System HRC - Bolt and nut assemblies with calibrated preload
EN 14399-10:2018

This draft European Standard specifies, together with EN 14399-1 and EN 14399-2, the requirements for assemblies of high-strength structural bolts and nuts of system HRC suitable for preloaded joints, with hexagon head (large widths across flats), cup head or countersunk head, thread sizes M12 to M36 and property class 10.9/10.
Bolting assemblies in accordance with this document have been designed to allow preloading of at least 0,7 fub × As according to EN 1993-1-8 (Eurocode 3) and to obtain ductility predominantly by plastic elongation of the bolt. For this purpose the components have the following characteristics:
-   regular nut height according to (style 1), see EN ISO 4032, or
-   nut with height m = 1 D,
-   thread length of the bolt in accordance with ISO 888.
Bolting assemblies in accordance with this document include washers according to EN 14399-6 or to EN 14399-5 (under the nut only).
NOTE   Attention is drawn to the importance of ensuring that the bolting assemblies are correctly used if a satisfactory result is to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made.
General requirements and requirements for suitability for preloading are specified in EN 14399-2 and in Clause 8 of this document.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 2320:2016(Main)
Fasteners - Prevailing torque type steel nuts - Mechanical and performance properties (ISO 2320:2015)
EN ISO 2320:2015

This International Standard specifies the functional properties for prevailing torque steel nuts when
tested at an ambient temperature range of +10 °C to +35 °C. It includes a combined test method to
determine the prevailing torque properties and the torque/clamp force properties at the same time.
It applies to prevailing torque all metal type nuts and prevailing torque non-metallic insert type nuts:
— with triangular ISO thread in accordance with ISO 68-1;
— with diameter/pitch combination in accordance with ISO 261 and ISO 262;
— with coarse pitch thread M5 to M39 or with fine pitch thread M8 × 1 to M39 × 3;
— with thread tolerances in accordance with ISO 965-2;
— with mechanical properties in accordance with ISO 898-2;
Prevailing torque values specified in this standard are based on laboratory test conditions.
NOTE 1 Actual prevailing torques in practical application can vary.
NOTE 2 All metal type nuts conforming to the requirements of this International Standard are used in
applications ranging from −50 °C to +150 °C.
NOTE 3 Non-metallic insert type nuts conforming to the requirements of this International Standard are used
in applications ranging from −50 °C to +120 °C.
WARNING — Temperatures outside the ambient temperature range can influence the functional
properties (torque/clamp force and prevailing torque properties), see Annex A.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14399-4:2015(Main)
High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies
EN 14399-4:2015

This document specifies together with EN 14399-1 the requirements for assemblies of high-strength structural bolts and nuts of system HV suitable for preloaded joints with large widths across flats, thread sizes M12 to M36 and property classes 10.9/10.
Bolt and nut assemblies to this document have been designed to allow preloading of at least 0,7 fub x As 1) according to EN 1993-1-1 (Eurocode 3) and to obtain ductility predominantly by plastic deformation of the engaged threads. For this purpose the components have the following characteristics:
-  nut height approximately 0,8 d
-  bolt with short thread length
Bolt and nut assemblies according to this document include washers according to EN 14399-6.
NOTE   Attention is drawn to the importance of ensuring that the bolts are correctly used if satisfactory result are to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made.
The requirements for suitability for preloading are specified in EN 14399-2.
Clamp lengths and grip lengths for the bolt/nut/washer assemblies are given in the normative Annex A.
----------------------------
1) fub is the nominal tensile strength (Rm) and As the stress area of the bolt.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14399-3:2015(Main)
High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies
EN 14399-3:2015

This document specifies, together with EN 14399 1, the requirements for assemblies of high-strength structural bolts and nuts of system HR suitable for preloaded joints with large widths across flats, thread sizes M12 to M36 and property classes 8.8/8 and 10.9/10.
Bolt and nut assemblies to this document have been designed to allow preloading of at least 0,7 fub x As 1) according to EN 1993-1-1 (Eurocode 3) and to obtain ductility predominantly by plastic elongation of the bolt. For this purpose the components have the following characteristics:
-  nut height according to style 1 (see EN ISO 4032);
-  thread length of the bolt according to ISO 888.
Bolt and nut assemblies to this document include washers according to EN 14399-6 or to EN 14399-5 (under the nut only).
NOTE   Attention is drawn to the importance of ensuring that the bolts are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made.
The requirements for suitability for preloading are specified in EN 14399-2.
Clamp lengths and grip lengths for the bolt/nut/washer assemblies are given in the normative Annex A.
--------------------------------------------------------------
1) fub is the nominal tensile strength (Rm) and As the stress area of the bolt.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 21670:2014(Main)
Fasteners - Hexagon weld nuts with flange (ISO 21670:2014)
EN ISO 21670:2014

EN ISO 21670 specifies characteristics for hexagon weld nuts with flange, with sizes M5 to M16 (coarse thread) or D = 8 mm to 16 mm (fine pitch thread), of product grade A. Weld nuts conforming to this International Standard are suitable for use with bolts of property classes up to 10.9 according to ISO 898-1.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day