iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 500-5:2000

(Main)

Mobile road construction machinery - Safety - Part 5: Specific requirements for joint cutters

Mobile road construction machinery - Safety - Part 5: Specific requirements for joint cutters

This part of EN 500 specifies the safety requirements for joint cutters as defined in clause 3 and deals with the significant hazards pertinent to joint cutters, when used as intended and in conditions foreseen by the manufacturer.

Bewegliche Straßenbaumaschinen - Sicherheit - Teil 5: Besondere Anforderungen an Fugenschneider

Teil 5 dieser Norm legt die sicherheitstechnischen Anforderungen für Fugenschneider - wie in Abschnitt 3 definiert - fest, und behandelt die artspezifischen Gefährdungen, die von Fugenschneider ausgehen, wenn sie bestimmungsgemäß entsprechend den Empfehlungen des Herstellers verwendet werden.

Machines mobiles pour la construction de routes - Sécurité - Partie 5: Exigences spécifiques pour découpeurs de joints

La partie 5 de cette norme prescrit les exigences de sécurité applicables aux découpeurs de joints - tels qu'ils sont définis dans l'article 3 - et traite les phénomenes dangereux significatifs résultant des découpeurs de joints, quand ils sont utilisés normalement et conformément aux recommandations du fabricant.

Mobile road construction machinery - Safety - Part 5: Specific requirements for joint cutters

General Information

Status
Withdrawn
Publication Date
31-Mar-2000
Withdrawal Date
10-Feb-2009
ICS
93.080.10 - Road construction
Technical Committee
I13 - Imaginarni 13
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
16-Jan-2009
Due Date
08-Feb-2009
Completion Date
11-Feb-2009
Directive
89/392/EEC - Machinery - Safety of machinery: general essential health and safety requirements
98/37/EC - Machinery
Mandate
M/BC/CEN/91/1 - Standardization request to CEN/CENELEC concerning machines presenting hazards due to mobility or load lifting
Ref Project
EN 500-5:1995 - Mobile road construction machinery - Safety - Part 5: Specific requirements for joint cutters

Relations

Replaced By
SIST EN 13862:2002 - Floor cutting-off machines - Safety
Effective Date
01-Jan-2002
Parent
SIST EN 500-2:2000 - Mobile road construction machinery - Safety - Part 2: Specific requirements for road-milling machines
Effective Date
22-Dec-2008

Buy Standard

EN 500-5:2000EN 500-5:2000
PreviousNext
Standard
EN 500-5:2000
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 500-5:2000
01-april-2000
Mobile road construction machinery - Safety - Part 5: Specific requirements for
joint cutters
Mobile road construction machinery - Safety - Part 5: Specific requirements for joint
cutters
Bewegliche Straßenbaumaschinen - Sicherheit - Teil 5: Besondere Anforderungen an
Fugenschneider
Machines mobiles pour la construction de routes - Sécurité - Partie 5: Exigences
spécifiques pour découpeurs de joints
Ta slovenski standard je istoveten z: EN 500-5:1995
ICS:
93.080.10 Gradnja cest Road construction
SIST EN 500-5:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote a
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 13862:2022(Main)
Floor cutting-off machines - Safety
EN 13862:2021

This document applies to pedestrian controlled floor sawing machines having power feed, manual feed or hand feed (see 3.2) for sawing, grooving and milling floor surfaces made of concrete, asphalt and similar mineral building materials where the main power is supplied by electric or internal combustion prime engine. The power transmission of floor sawing machines is mechanical or hydraulic.
This document deals with all significant hazards pertinent to floor sawing machines, when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.
These machines are designed for use with rotating cutting-off wheels for wet and dry cutting. These cutting-off wheels can be either a diamond cutting-off wheel or a boron nitride cutting-off wheel, according to EN 13236.
This document does not apply to:
-   self-propelled ride-on floor sawing machines;
-   machines moving along a rail;
-   hand-held portable cutting off machines for construction materials mounted on a mobile support, to be used as floor saws;
-   remote controlled machines.
This document covers electrical hazards by making reference to relevant European Standards (see 4.2).
Those hazards that are relevant for all mechanical, electrical, hydraulic and other equipment or machinery and that are dealt with in standards for common use are not covered by this document. Reference to pertinent standards is made where such standards are applicable and so far necessary.
In this document, floor sawing machines are called "machines", and cutting-off wheels are called "tools".
This document applies primarily to machines which are manufactured after the date of approval of the standard by CEN.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16165:2021(Main)
Determination of slip resistance of pedestrian surfaces - Methods of evaluation
EN 16165:2021

This document specifies test methods for the determination of the slip resistance of surfaces in the most commonly encountered situations in which pedestrians walk.
NOTE   It is also possible to use this document for measurements where persons might walk on trafficked areas.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13020:2016(Main)
Road surface treatment machines - Safety requirements
EN 13020:2015

This document applies to road surface treatment machines, which are in particular:
- binder sprayers [or sprayers];
- chipping spreaders [or spreaders];
- machines for surface repairs !(binder sprayer chipping spreader [or sprayer spreader]);
- mastics asphalt mixers;
- joint sealer;
- micro-surfacing machines/slurry machines;
(see also Clause 3).
Road surface treatment machines can be mounted on a carrier vehicle, trailer or articulated truck, combining
to form an integral unit. It is also possible to mount a road surface treatment machine on its own chassis
construction and propulsion system (self-propelled or pedestrian-controlled). In all cases the machine and
chassis form an integral unit.
Directives and standards for the vehicular truck chassis aspects, termed 'carrier vehicle' in this document,
would be those relative to that equipment, even where specific modifications have been made to realize the
road surface treatment application. The use in public road traffic is governed by the national regulations.
This document deals with all significant hazards identified through a risk assessment relevant to road surface
treatment machines when they are used as intended and under the conditions foreseen by the manufacturer
(see Clause 4). This document does not deal with significant hazards associated with pressurized tanks, noise
and EMC. This document specifies the appropriate technical measures to eliminate or reduce risks arising
from the significant hazards associated with machine operation, setting and adjustments, load discharge and
routine maintenance.
This document does not include requirements for the carrier vehicles or special constructions. These are
covered in directives related to the construction of vehicles. Demountable bodywork systems (e.g.
demountable containers) are specified in other standards. !Vibrations are not dealt with in the standard,
because for all machines of this family vibration is not a relevant hazard due to the low working speed and
special working conditions (e.g. flat surface).

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 536:2015(Main)
Road construction machines - Mixing plants for road construction materials - Safety requirements
EN 536:2015

This European Standard specifies the safety requirements applicable to stationary and relocatable mixing plants for the production of materials (e.g. hot-mix asphalt, cold-mix asphalt, cement gravel) used for the construction and maintenance of traffic routes (roads, highways, sidewalks, airfields, etc.) water retaining works, dam walls, culverts, etc.
This European Standard applies to the following types of mixing plant:
a)   hot Asphalt mixing plant;
b)   cold mixing plant (e.g. for production of cement gravel, cold mix asphalt);
c)   mixing plant for bituminous or non-bituminous reclaimed materials;
d)   mixing plant for mastic asphalt, also including natural asphalt.
Machines moving during the working process (e.g. mobile mastic asphalt mixers) and crushers are not covered by this European Standard.
Those types of asphalt mixing plants can also be combined or enlarged by additional installations (e.g. Plant for storage of binders (e.g. bituminous, synthetic, vegetal).
This European Standard deals with all significant hazards pertinent to mixing plants, when they are used as intended and under the conditions of misuse which are reasonably foreseen by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.
This European Standard does not apply to machines for the production of cement concrete and mortar as covered in EN 12151.
This European Standard does not deal with hazards caused by flammable gases. As soon as information is available it will be included.
This European Standard is not applicable to mixing plants for road construction materials, which are manufactured before the date of publication of this European Standard by CEN.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 500-4:2011(Main)
Mobile road construction machinery - Safety - Part 4: Specific requirements for compaction machines
EN 500-4:2011

This part of EN 500 specifies the safety requirements for compaction machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to compaction machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This document specifies additional requirements to and/or exceptions from EN 500-1 ”Common requirements”. This part of EN 500 is not applicable for seated ride-on operated rollers with a drum width less than nominal 0,8 m.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 500-1:2007+A1:2010(Main)
Mobile road construction machinery - Safety - Part 1: Common requirements
EN 500-1:2006+A1:2009

This part of EN 500 specifies the common safety requirements for mobile road construction machinery 1) . The EN 500 series is applicable to mobile road construction machinery as listed in Annex A. When no specific standard exists, EN 500-1 applies. It specifies common requirements for the design and construction of mobile road construction machinery in order to protect workers from accidents and health hazards which could occur during operation, loading, transport and maintenance. Additional specific requirements for certain types of mobile road construction machinery are given in parts 2 to 4 and 6 of this standard. This part of this standard gives safety requirements for all types of mobile road construction machinery and shall be used in conjunction with one of the parts 2 to 4 and 6. These machine-specific parts do not repeat the requirements from part 1 but add to or replace the requirements for the type of mobile road construction machinery in question. Machine-specific requirements in parts 2 to 4 and 6 take precedence over the respective requirements of this standard. For types of mobile road construction machinery not dealt with in parts 2 to 4 and 6, EN 500-1 applies !and if for those machinery additional derived risks may arise, these risks have to be taken into consideration". This European Standard deals with all significant hazards, hazardous situations and events relevant to mobile road construction machinery, when they are used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards as specified in Clause 4. This European Standard applies to machines which are manufactured after the date of publication of this European Standard by CEN.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 500-3:2007+A1:2008(Main)
Mobile road construction machinery - Safety - Part 3: Specific requirements for soil-stabilising machines and recycling machines
EN 500-3:2006+A1:2008

This part of EN 500 specifies the safety requirements for soil-stabilising machines and recycling machines as de-fined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to these ma-chines, when they are used as intended and under conditions of misuse which are reasonably foreseeable.
This part of EN 500 contains additional requirements to EN 500-1 "Common requirements".

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 500-2:2007+A1:2008(Main)
Mobile road construction machinery - Safety - Part 2: Specific requirements for road-milling machines
EN 500-2:2006+A1:2008

This part of EN 500 specifies the safety requirements for road-milling machines as defined in Clause 3 and deals with all significant hazards, hazardous situations and events relevant to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable.
This part of EN 500 contains additional requirements to EN 500-1 "Common requirements".

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 500-6:2007+A1:2008(Main)
Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers
EN 500-6:2006+A1:2008

This part of EN 500 specifies the safety requirements for paver-finishers as defined in Clause 3 and deals with the significant hazards relevant to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable. This part of EN 500 contains additional requirements to EN 500-1 "Common requirements".
If internal and/or external vibrators are used for concrete paving, then prEN 12649 applies.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN ISO 20500-7:2020(Main)
Mobile road construction machinery - Safety - Part 7: Specific requirements for slipform paver and texture curing machines (ISO/DIS 20500-7:2020)
prEN ISO 20500-7

This part of ISO 20500, together with part 1, deals with all significant hazards for slipform paver and texture curing machines when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer associated with the whole life time of the machine (see Clause 4).
The requirements of this part are complementary to the common requirements formulated in ISO 20500-1.
This document does not repeat the requirements from ISO 20500-1, but adds or replaces the requirements for application for slipform paver and texture curing machines.

  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day