SIST-TP CEN/TR 15953:2009
(Main)Pyrotechnic articles - Other pyrotechnic articles, category P1 and P2 - Overview of harmonized standards that will be developed by CEN/TC 212/WG 5
Pyrotechnic articles - Other pyrotechnic articles, category P1 and P2 - Overview of harmonized standards that will be developed by CEN/TC 212/WG 5
This Technical Report gives an overview of harmonised standards which will be proposed to be developed by CEN/TC 212 WG 5, Other Pyrotechnic Articles. Under this expression, it must be understood, are all pyrotechnic articles which are not designed and intended for entertainment purposes (fireworks), for indoor or outdoor stage use, including film and television productions or similar use (theatrical pyrotechnic articles), and for automotive industry (pyrotechnic articles for vehicles). It also gives the interpretation WG5 experts have made of some terms, definitions and requirements of Directive 2007/23/EC in order to assure future harmonised standards will encompass all varieties of other pyrotechnic articles, which are presently placed on the European market, in a consistent way and take the benefit of all the practical experience and usages of those articles in the Member States.
Pyrotechnische Gegenstände - Sonstige pyrotechnische Gegenstände, Kategorien P1 und P2 - Überblick über harmonisierte Normen, die von CEN/TC 212/WG 5 erarbeitet werden
Articles pyrotechniques - Autres articles pyrotechniques de catégories P1 et P2 - Vue d'ensemble des normes harmonisées qui seront élaborées par le CEN/TC 212/WG 5
Le présent Rapport Technique donne une vue d’ensemble des normes harmonisées que le Groupe de Travail n°5, « Autres articles pyrotechniques », du Comité Technique CEN/TC 212 proposera de développer. Avec cette expression, il doit être compris qu’il s’agit de tous les articles pyrotechniques qui ne sont pas conçus et prévus à des fins de distraction (« artifices de divertissement »), pour une utilisation sur scène à l’intérieur et à l’extérieur, y compris les productions cinématographiques et télévisuelles ou une utilisation similaire (« articles pyrotechniques pour le spectacle »), et pour l’industrie automobile (« articles pyrotechniques pour véhicules »).
Il donne également l'interprétation que les experts du Groupe de Travail n°5 ont retenu pour certains termes, définitions et exigences de la Directive 2007/23/CE afin d'assurer que les futures normes harmonisées engloberont d'une manière cohérente tous les types « d’autres articles pyrotechniques », qui sont actuellement mis sur le marché européen et tireront bénéfice de toute l'expérience pratique et des utilisations de ces artifices dans les Etats membres.
Pirotehnični izdelki - Drugi pirotehnični izdelki, kategorij P1 in P2 - Pregled harmoniziranih standardov, ki jih pripravlja CEN/TC 212/WG 5
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TP CEN/TR 15953:2009
01-december-2009
3LURWHKQLþQLL]GHONL'UXJLSLURWHKQLþQLL]GHONLNDWHJRULM3LQ33UHJOHG
KDUPRQL]LUDQLKVWDQGDUGRYNLMLKSULSUDYOMD&(17&:*
Pyrotechnic articles - Other pyrotechnic articles, category P1 and P2 - Overview of
harmonized standards that will be developed by CEN/TC 212/WG 5
Pyrotechnische Gegenstände - Sonstige pyrotechnische Gegenstände, Kategorien P1
und P2 - Überblick über harmonisierte Normen, die von CEN/TC 212/WG 5 erarbeitet
werden
Articles pyrotechniques - Autres articles pyrotechniques de catégories P1 et P2 - Vue
d'ensemble des normes harmonisées qui seront élaborées par le CEN/TC 212/WG 5
Ta slovenski standard je istoveten z: CEN/TR 15953:2009
ICS:
71.100.30 Eksplozivi. Pirotehnika Explosives. Pyrotechnics
SIST-TP CEN/TR 15953:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TP CEN/TR 15953:2009
---------------------- Page: 2 ----------------------
SIST-TP CEN/TR 15953:2009
TECHNICAL REPORT
CEN/TR 15953
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
October 2009
ICS 71.100.30
English Version
Pyrotechnic articles - Other pyrotechnic articles, category P1
and P2 - Overview of harmonized standards that will be
developed by CEN/TC 212/WG 5
Articles pyrotechniques - Autres articles pyrotechniques de Pyrotechnische Gegenstände - Sonstige pyrotechnische
catégories P1 et P2 - Vue d'ensemble des normes Gegenstände, Kategorien P1 und P2 - Überblick über
harmonisées qui seront élaborées par le CEN/TC 212/WG harmonisierte Normen, die von CEN/TC 212/WG 5
5 erarbeitet werden
This Technical Report was approved by CEN on 17 August 2009. It has been drawn up by the Technical Committee CEN/TC 212.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 15953:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TP CEN/TR 15953:2009
CEN/TR 15953:2009 (E)
Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Terminology .5
3 Interfaces between Working Groups .7
4 List of Other Pyrotechnic Articles and definitions .9
5 Criteria to determine whether an article belongs to Category P1 or P2 . 11
6 Harmonized Standards . 12
7 Projects to be initiated within WG 5 (List and Mandates) . 14
8 Future Work Program (Objectives, Tasks, Time targets) . 16
Annex A (informative) Definition of Other Pyrotechnic Articles – Complementary Information . 19
Annex B (informative) Field of Use . 21
Annex C (informative) List of "Other Pyrotechnic Articles" and definitions . 22
Annex D (informative) List of Generic Types and definitions . 27
Annex E (informative) Interpretation of "Low Hazard" - Examples . 30
Bibliography . 31
2
---------------------- Page: 4 ----------------------
SIST-TP CEN/TR 15953:2009
CEN/TR 15953:2009 (E)
Foreword
This document (CEN/TR 15953:2009) has been prepared by Technical Committee CEN/TC 212 “Pyrotechnic
articles”, the secretariat of which is held by NEN.
This document (CEN/TR 15953:2009) has been prepared by Working Group 5 “Other pyrotechnic articles” of
Technical Committee CEN/TC 212 “Pyrotechnic articles”, the convenor and secretary of which are French.
Experts from eleven countries have participated in its elaboration: Belgium, Czech Republic, Denmark,
France, Germany, Italy, Romania, Spain, Switzerland, The Netherlands and United Kingdom.
It has been approved by votes of all the members of CEN/TC 212 “Pyrotechnic articles” on August 2009.
3
---------------------- Page: 5 ----------------------
SIST-TP CEN/TR 15953:2009
CEN/TR 15953:2009 (E)
Introduction
rd
Directive 2007/23/EC of May 23 2007 on the placing on the market of pyrotechnic articles, has been
th
published on June 14 2007 in the Official Journal of the European Community. (Ref. Mandate M 416).
In its Annex 1, Directive 2007/23/EC gives the essential safety requirements (ESR) pyrotechnic articles shall
comply with. In order to facilitate the process of demonstrating compliance with these ESR, harmonized
standards for the design, manufacture and testing of pyrotechnic articles must be developed.
CEN has been mandated by the European Commission (EC) to develop these harmonized standards:
Mandate M 416 describes the work that CEN shall perform.
CEN has entrusted coordination of this work to CEN/TC 212 ‘Pyrotechnic articles’ with the following scope:
“Standardization of fireworks, theatrical pyrotechnic articles, pyrotechnic articles for vehicles and other
pyrotechnic articles, particularly from the point of view of their safe use”.
th th
During its meeting in Delft on October 16 and 17 2007, CEN/TC 212 has decided to share the
corresponding work to be done between several Working Groups. Resolutions have been voted to establish
five Working Groups, one of which is Working Group 5 (CEN/TC 212 / WG 5) in charge of standardization of
“Other Pyrotechnic Articles”.
Because no European standards exist at present for “Other Pyrotechnic Articles”, preliminary work needs to
be performed before a list of standards to be developed by WG 5 can be drawn up. It has been accepted by
CEN/TC 212 and proposed to the European Community a one-year period will be allocated to WG5 to prepare
a CEN Technical Report in which its future work program will be described and an overview of the harmonized
standards it will develop will be given including the reasons why WG 5 has proposed to develop these
standards.
th
Five work sessions have taken place, respectively in NEN – Delft – Netherlands on February 7 2008, in BAM
nd th
– Berlin – Germany on May 22 2008, in NEN – Delft – Netherlands on September 9 2008, in AFNOR –
th
Paris – France on November 13 2008 and in UNI – Milano – Italy on February 2 2009.
The present document is the final draft of the Technical Report for “Other Pyrotechnic Articles”. It has been
written in close coordination with the other working groups of CEN/TC 212/WG 1 “Fireworks, Categories 1, 2
and 3”, WG 2 “Fireworks, Category 4”, WG 3 “Theatrical Pyrotechnic articles” and WG 4 “Pyrotechnic articles
for vehicles”.
4
---------------------- Page: 6 ----------------------
SIST-TP CEN/TR 15953:2009
CEN/TR 15953:2009 (E)
1 Scope
This Technical Report gives an overview of harmonized standards which will be proposed to be developed by
CEN/TC 212 WG 5, “Other Pyrotechnic Articles”. Under this expression, it must be understood, are all
pyrotechnic articles which are not designed and intended for entertainment purposes (“fireworks”), for indoor
or outdoor stage use, including film and television productions or similar use (“theatrical pyrotechnic articles”),
and for automotive industry (“pyrotechnic articles for vehicles”).
It also gives the interpretation WG5 experts have made of some terms, definitions and requirements of
Directive 2007/23/EC in order to assure future harmonized standards will encompass all varieties of “other
pyrotechnic articles”, which are presently placed on the European market, in a consistent way and take the
benefit of all the practical experience and usages of those articles in the Member States.
2 Terminology
2.1 Definition of “Other pyrotechnic articles”
In its Article 2, Directive 2007/23/EC gives a definition of a “pyrotechnic article” as “any article containing
explosive substances or an explosive mixture of substances designed to produce heat, light, sound, gas or
smoke or a combination of such effects through self-sustained exothermic chemical reactions”.
Although heat, light, sound, gas or smoke or combination of such effects are more frequently obtained through
combustive or deflagrating reactions, this definition does not exclude substances or mixture of substances
which exhibit a detonative behaviour.
WG5 experts have considered that no other interpretation of the definition of pyrotechnic articles given by
Directive 2007/23/EC is required.
See Annex A for further information.
2.2 Other terms
Collections of articles: individual item/ article, type, group/family, generic type.
The future harmonized standards for “other pyrotechnic articles” will identify the design parameters and
performance characteristics to be taken into consideration for the corresponding articles to meet the essential
safety requirements of Directive 2007/23/EC. Where appropriate, for each design parameter or performance
characteristic they will state requirements and criteria which shall be complied with.
According to the large variety of other pyrotechnic articles and significant differences they exhibit in design,
functioning and conditions of use, it is clearly noticeable these articles will not have all in common the same
design parameters and performance characteristics. However, collections of articles sharing the same design
parameters and performance characteristics exist. Then WG 5 experts have considered it was necessary to
identify these collections of articles and draw up their list.
The future harmonized standards will state requirements and criteria for each identified homogeneous
collection, which does not mean there may not exist requirements or criteria applicable to several collections
as well as to all pyrotechnic articles whatever their design or behaviour in normal use.
5
---------------------- Page: 7 ----------------------
SIST-TP CEN/TR 15953:2009
CEN/TR 15953:2009 (E)
The following terms and definitions will be used hereafter and in the harmonized standard(s) to be developed
by Working Group5:
Type: sample representative of the production envisaged.
NOTE 1 This definition corresponds to the use of the term ‘type’ in Annex II §2(c) of Directive 2007/23/EC for the
purposes of type-examination.
Generic type: set of articles with a common, very general, design feature and/or with a common
characteristic effect.
Subtype: set of articles within a generic type with specific design features.
Individual item: article within a generic type or subtype for which every possible feature and
characteristic has been fixed.
NOTE 2 Each feature and characteristic will be specified in the technical name or a technical data sheet, as
appropriate.
Technical name: general description of an individual item.
Trade name: description of an individual item from a particular supplier.
Family: set of individual items that will be considered together for the purposes of testing and approval.
NOTE 3 This last definition is fully compliant with Directive 2007/23/EC which states in “Whereas (18)”: “Groups of
pyrotechnic articles that are similar in design, function or behaviour should be assessed by the notified bodies as product
families”.
The figure hereafter shows how WG 5 experts intend to organize “other pyrotechnic articles” in “individual
items” (samples of which will be “types”), “families” and “generic types”, starting from the precise design level
to the general design level. Example is given for “smoke generators”.
This will be very useful and efficient to clarify and solve the complexity of their work resulting from the large
variety of design of these “other pyrotechnic articles”. Even for a given kind of pyrotechnic article, developed
for the same type of use, strong variations in design may exist between manufacturers.
At the bottom, “individual items” correspond to the various individual smoke generators in a manufacturer’s
product range, under the brand name “Securix™”, submitted to conformity assessment procedures by the
means of “types”.
In the middle are set up “families” of individual items (e.g. family of “Securix™ Smoke generators”) which may
be considered together for the purposes of testing and certification in compliance with Directive 2007/23/EC.
At the top, the highest level of generalization of the characteristics of types corresponds to “Smoke
generators”, independently from who is the manufacturer and what is the typical design within a product
range. WG5 experts think all types of smoke generators can be put together in a unique collection of groups
because it is highly possible that the essential safety requirements of Directive 2007/23/EC will only imply
design and performance requirements which will be common to every type of smoke generators and none at a
lower level (e.g. that of a family). Then WG 5 harmonized standards will only deal with these “generic types”.
6
---------------------- Page: 8 ----------------------
SIST-TP CEN/TR 15953:2009
CEN/TR 15953:2009 (E)
Figure 1 – Generic type, family and item
For some applications it may be useful to take account of “field of use” (See Annex B). However, WG 5
experts have decided to develop future harmonized standards on generic types, not on the field of use.
2.3 Use of blasting agents and military explosives
In its Annex I § (4) (a) and (b), Directive 2007/23/EC of 23 May 2007 “on the placing on the market of
pyrotechnic articles” states pyrotechnic articles must contain neither commercial blasting agents, except for
black powder or flash composition, nor military explosives.
As some T1 and T2 articles and C4 Fireworks, P1 and P2 articles already contain small amounts of
explosives (e.g. nitrocellulose with high nitrogen content, single base or double base propellants one
component of which is nitroglycerine) and must not be excluded from the European market as far as they
comply with all the other essential safety requirements, except this § (4) (a) (b) of Directive 2007/23/EC /
Annex I. Hence they must be included within the scope of preparing Standards for “other pyrotechnic articles”
and to prepare suitable guidance.
CEN/TC 212 will prepare a specific resolution on that topic.
3 Interfaces between Working Groups
3.1 Interfaces between WG 5 and WG 1
WG1 has proposed to transfer:
electric igniters used for fireworks ignition to WG 5
friction-ignited flash bangers to WG 3 or WG 5
whistlers to WG 3 or WG 5
“Electric igniters used for fireworks ignition”: WG 5 accepts this proposal without restriction.
7
---------------------- Page: 9 ----------------------
SIST-TP CEN/TR 15953:2009
CEN/TR 15953:2009 (E)
“Friction-ignited flash bangers” and “whistlers”: WG 5 experts consider these products may enter into its scope
of work: for instance, they can be used as bird-scaring articles. They can also be used as “theatrical
pyrotechnic articles” for indoor or outdoor stage use, including film and television productions or similar use. Is
a common harmonized standard appropriate? Answer to this question will be given as early as possible during
the development phase of the corresponding harmonized standards: WG 3 and WG 5 experts will compare
their respective construction and performance requirements and propose their common view of the problem.
At present, WG 5 experts propose to create a corresponding generic type, called “Sound / Noise Emitters”,
which will include these two articles as well as other electrically or percussion actuated ones (See 4.3).
3.2 Interfaces between WG 5 and WG 2
Components of firework articles are often sold by manufacturers to other manufacturers in some European
countries. Is Directive 2007/23/EC applicable in that case? Do “Category 4 firework articles” include
components of fireworks such as stars, crackers, volcanoes, tourbillions, quick match, black match, cord
igniters, fuses or delays… from the point of view of Directive 2007/23/EC?
WG 5 experts consider the answer is positive, but with the following approach: components of fireworks must
be taken in consideration – if necessary and pertinent – by WG5 as “other pyrotechnic articles.
WG 2 and WG 5 experts have met the following agreement:
WG 5 will treat components of fireworks when they are used in other fields than fireworks (for example,
electric igniters, quick match, black match, cord igniters, pressed fuses, stars.).
When these components are strictly relevant to the fireworks market, they will enter into the scope of
work of WG 2 (for example, crackers, volcanoes, tourbillions).
3.3 Interfaces between WG 5 and WG 3
"Friction-ignited flash bangers” and “whistlers: See sub clause § 3.1 of this document.
Interpretation of “low hazard”: Definitions of T1 and P1 articles of Directive 2007/23/EC refer to “low hazard”
as a criterion to determine whether a “theatrical” or “other” pyrotechnic article is T1 or T2, P1 or P2. Because
“low hazard” is a very imprecise term and pyrotechnic articles already placed on the consumers market may
intrinsically present medium or high hazard from the point of view of some market surveillance organizations,
WG 3 and WG 5 have joined their efforts to give a common operative interpretation of “low hazard” for their
respective products (See 5.1 of this document).
3.4 Interfaces between WG5 and WG4
WG 4 experts consider igniters used as components in airbag inflators and other automotive pyrotechnic
devices must enter in the field of “pyrotechnic articles for vehicles” since they are specially designed for
automotive applications. In that case, WG 4 will create the corresponding standard and they will not be taken
in account by WG 5.
Such igniters may be used without modification or adaptation in other applications than automotive. WG 4 and
WG 5 experts agree on the following approach:
Every automotive igniter will have a specific reference for its use in pyrotechnic devices for vehicles. This
reference will correspond to specific automotive specifications and qualification tests will aim to confirm
their compliance to these specifications. Type-certification will be made according to the applicable WG 4
standard. The data sheet of the product will indicate “to be only used for automotive applications”.
8
---------------------- Page: 10 ----------------------
SIST-TP CEN/TR 15953:2009
CEN/TR 15953:2009 (E)
For other applications, even with an identical design, the automotive igniters will preferably have a
different reference, as they are supposed to comply with different specifications and be possibly
submitted to a different qualification process. Because WG 5 and WG 4 shall prepare separate standards
for electric igniters, a comparison of these two standards will be made to determine what standard – the
most restrictive – will be applicable when electric igniters developed for automotive industry are used
outside this industry.
In every case, igniters which will have been submitted to type-examination according to the more
restrictive harmonized standard will not need to be tested again.
4 List of Other Pyrotechnic Articles and definitions
4.1 Preliminary inventory and definitions
An extraction of articles liable to enter in categories P1-P2 has been made from the lists of pyrotechnic articles
given in Annexes I and II of Directive 2004/57/EC of 23 April 2004. But WG 5 experts have considered these
two lists were not exhaustive enough. They have also considered some UN definitions needed to be improved
whenever it was necessary for the purpose of their future development work of harmonized standards.
Then, WG 5 experts have tried to inventory more adapted collections of articles and have drawn up a new list
of possible “other pyrotechnic articles”, with corresponding definitions. This list is given in Annex C.
This inventory has been based on the knowledge of WG 5 experts who attended the different meetings of this
working group. Examples have been given by each of them to illustrate the above definitions. These examples
are not cited in the present Technical Report, but they remain available as working documents which will
possibly be used by Project Leaders during the development phase of harmonised standards.
To assure exhaustiveness of their inventory, WG 5 experts have also made a review of substances and
articles which have been attributed a UN Number – and which are not obviously “ammunition”, “articles for use
by the police or armed forces” or “articles and substances falling merely and undoubtedly under
Directive 93/15/EEC” – has also been made to identify those which may be considered as “pyrotechnic
articles” provided some conditions are met to be determined and proposed by WG 5 experts, then fixed by the
corresponding harmonized standards.
4.2 Criteria used to determine “generic types”
This inventory shows articles which correspond to very different situations:
some are associated to rather precise product architectures or designs, others are very general, others
are located at mid distance between these “very general” and “rather precise” articles;
others may appear to be collections of several generic types;
others belong to specific fields of use.
Development of harmonized standards for “other pyrotechnic articles” requires a preliminary determination of
“generic types”. WG5 experts have decided to give priority to “generic types” based on general construction or
performance characteristics without reference to their possible field of use. Exceptions would be treated later if
and only if a professional sector requires them and justifies the specific character of its requirements
(See 4.4).
9
---------------------- Page: 11 ----------------------
SIST-TP CEN/TR 15953:2009
CEN/TR 15953:2009 (E)
WG 5 experts have decided to generalize the construction and performance characteristics as much as
possible, after having taken notice that:
from the point of view of public safety, it may not be relevant to distinguish such effects as heat, light, fog
and smoke, but on the contrary it may be important to keep pressure or gas flow separate when building
“generic types”;
“generic types” must be strictly determined only by the technical design and performance characteristics
which are relevant from the point of view of the essential safety requirements of Directive 2007/23/EC;
this will lead to determine requirements on a limited number of construction and performance
characteristics;
as a consequence of this limited number of construction and performance characteristics, possible
candidates can be grouped under a sole generic type as far as specific requirements resulting from their
different general design will be limited to a few short chapters in the corresponding harmonized
standards.
WG 5 experts have then decided to determine these generic types using two alternative criteria:
common architecture whatever the effect as far as it leads to similar consequences in terms of public
safety: e.g. “other generators” including heat, light, fog and smoke generators (but not gas generators),
the architecture of which consists of “a casing, with an ignition device and a combustive pyrotechnic
grain, and may include a safe and arm device, filters, heat exchangers, drying charges, etc.”
or common generic function to be fulfilled whatever the differences of design and the field of use: e.g.
“igniters and primers” including electrically, optically or mechanically actuated items, the function of which
is to “to start deflagration in an explosive train”.
4.3 Generic types: list, definitions and examples
Doing this, WG 5 experts have determined 16 generic types on which will be placed design and performance
requirements in the future harmonized standards for “other pyrotechnic articles”.
These “generic types” are the following:
Flash cartridges Gas generators (including power cartridges)
Other cartridges Smoke / Fog generators
Components for pyrotechnic trains Igniters (including primers)
Pyrotechnic cords and fuses Pyrotechnic matches
Pressed fuses Pyromechanical devices
Flares Semi finished pyrotechnic products
Noise emitters Rockets and their motors
Fuzes Heaters
For corresponding definitions, comments and description of principal effects, see Annex D.
10
---------------------- Page: 12 ----------------------
SIST-TP CEN/TR 15953:2009
CEN/TR 15953:2009 (E)
4.4 ESR
As said before, WG 5 experts have decided to give priority to “generic types” based on general construction or
performance characteristics without reference to their possible field of use. The construction and performance
requirements will be determined for these general characteristics in the WG 5 harmonized standards.
However, a generic function to be fulfilled in a common field of use by a given “generic type” may lead to the
necessity of specific complementary requirements. This will be treated in a specific paragraph of the
harmonized standard of this “generic type” (See 6.2).
In that harmonised standard, a specific paragraph will also be necessary to describe what must be done in the
case a new field of use lead to the same situation.
However this rule may suffer exceptions if a given field of use implies specific requirements which are too
distant from other uses of similar products to be encompassed in the same harmonized standards (e.g.
“distress signals submitted to SOLAS regulations” but, in that case, specific standards have already been
developed).
Such exceptions would be treated later if and only if a professional sector requires them and justify the
specific character of its requirements.
5 Criteria to determine whether an article belongs to Category P1 or P2
5.1 Interpretation of “low hazard”
Directive 2007/23/EC gives the following definitions of P1 and P2 articles:
Category P1: pyrotechnic articles other than fireworks and theatrical pyrotechnic articles which present
a low hazard;
Category P2: pyrotechnic articles other than fireworks and theatrical pyrotechnic articles which are
intended for handling or use only by persons with specialist knowledge.
These definitions raise the following questions:
What means “low hazard”?
What about products which present more than a “low hazard” and are intended for handling or use by
persons without specialist knowledge? (See Annex E).
Then WG5 experts agree that articles, under certain conditions to be detailed in the corresponding standard,
may be P1 if user’s instructions can be easily understood by every person and applied without ambiguity.
They propose to state their interpretation of “low hazard” as follows:
1) Criteria for P1 will be based on the article’s hazard and/or pyrotechnic content and weight.
2) Articles, under certain conditions to be detailed in the corresponding standards (e.g. use of a specific
tool, capacity to assure safety distances), may be P1 if user’s instructions can be easily understood
by every person and applied without ambiguity.
th
CEN/TC 212 has approved this interpretation at its plenary meeting on November 14 2008 in Paris
(See Resolution Nr 37/2008).
11
---------------------- Page: 13 ----------------------
SIST-TP CEN/TR 15953:2009
CEN/TR 15953:2009 (E)
6 Harmonized Standards
6.1 Existing documents
The only documents concerning “other pyrotechnic articles” which have been found by WG 5 experts deal with
“fastening cartridges” (See Ref. [3]). A link will be necessary with CEN/TC/213 which has the mandate to
develop harmonized standards for the tools used for wall sealing and similar appliances.
6.2 List and Titles of Harmonized Standards to be developed
WG 5 experts propose to limit the list of harmonized standards to be developed for other pyrotechnic articles
to:
a specific standard for “ignition devices” (Cf. specific Essential Safety Requirements in Directive
2007/23/EC – See Annex I - § (5) C).
a specific standard for other generic types, composed of five parts in the same manner as done by WG 1:
Part 1: Terminology
Part 2: Requirements (construction and performance requirements to comply with ESR)
Part 3: Categorization (P1 or P2?)
Part 4: Test Methods
Part 5: Labelling a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.