iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN ISO 6076:2023

(Main)

Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles - Specification of trowel notch sizes (ISO 6076:2023)

Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles - Specification of trowel notch sizes (ISO 6076:2023)

This International Standard specifies the individual measurements of notches and assigns specific codes which may then be used to label notched tools complying with the measurements and tolerances specified in this standard.

Klebstoffe - Einbau von Bodenbelägen, Holzböden, Spachtelmassen und Fliesen - Festlegung von Zahnspachtelgrößen (ISO 6076:2023)

Dieses Dokument legt die einzelnen Abmessungen von Zahnungen fest. Es weist spezifische Codes zu, die zur Kennzeichnung von gezahnten Werkzeugen entsprechend den in diesem Dokument festgelegten Abmessungen und Toleranzen verwendet werden.

Adhésifs - Pose de revêtements de sol, planchers en bois, ragréages et carrelages - Spécifications des tailles des crans des peignes et spatules (ISO 6076:2023)

Le présent document spécifie les caractéristiques dimensionnelles individuelles des crans. Il attribue des codes spécifiques utilisés pour étiqueter les outils crantés en fonction des dimensions et des tolérances exposées dans ce dernier.

Lepila - Polaganje talnih oblog, lesenih talnih oblog, izravnalnih mas in ploščic - Specifikacija velikosti zobatih plazen (ISO 6076:2023)

Ta mednarodni standard določa posamezne mere zarez in posebne kode, ki se jih nato lahko uporabi za označevanje zarezanih orodij, ki ustrezajo meram in tolerancam, določenim v tem standardu.

General Information

Status
Published
Public Enquiry End Date
03-May-2022
Publication Date
27-Jun-2023
ICS
83.180 - Adhesives
Technical Committee
IPMA - Polimer materials and products
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
15-Jun-2023
Due Date
20-Aug-2023
Completion Date
28-Jun-2023
Ref Project
EN ISO 6076:2023 - Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles - Specification of trowel notch sizes (ISO 6076:2023, Corrected version 2023-09)

Buy Standard

EN ISO 6076:2023EN ISO 6076:2023
PreviousNext
Standard
EN ISO 6076:2023
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
prEN ISO 6076:2022prEN ISO 6076:2022
PreviousNext
Draft
prEN ISO 6076:2022
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 6076:2023
01-september-2023
Lepila - Polaganje talnih oblog, lesenih talnih oblog, izravnalnih mas in ploščic -
Specifikacija velikosti zobatih plazen (ISO 6076:2023)
Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles -
Specification of trowel notch sizes (ISO 6076:2023)
Klebstoffe - Einbau von Bodenbelägen, Holzböden, Spachtelmassen und Fliesen -
Festlegung von Zahnspachtelgrößen (ISO 6076:2023)
Adhésifs - Pose de revêtements de sol, planchers en bois, ragréages et carrelages -
Spécifications des tailles des crans des peignes et spatules (ISO 6076:2023)
Ta slovenski standard je istoveten z: EN ISO 6076:2023
ICS:
83.180 Lepila Adhesives
SIST EN ISO 6076:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 6076:2023

---------------------- Page: 2 ----------------------
SIST EN ISO 6076:2023


EN ISO 6076
EUROPEAN STANDARD

NORME EUROPÉENNE

June 2023
EUROPÄISCHE NORM
ICS 83.180
English Version

Adhesives - Installation of floor coverings, wood flooring,
levelling compounds and tiles - Specification of trowel
notch sizes (ISO 6076:2023)
Adhésifs - Pose de revêtements de sol, planchers en Klebstoffe - Einbau von Bodenbelägen, Holzböden,
bois, ragréages et carrelages - Spécifications des tailles Spachtelmassen und Fliesen - Festlegung von
des crans des peignes et spatules (ISO 6076:2023) Zahnspachtelgrößen (ISO 6076:2023)
This European Standard was approved by CEN on 16 April 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6076:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 6076:2023
EN ISO 6076:2023 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 6076:2023
EN ISO 6076:2023 (E)
European foreword
This document (EN ISO 6076:2023) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 193 “Adhesives” the secretariat of which is held by
UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2023, and conflicting national standards
shall be withdrawn at the latest by December 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 6076:2023 has been approved by CEN as EN ISO 6076:2023 without any modification.

3

---------------------- Page:
...

SLOVENSKI STANDARD
oSIST prEN ISO 6076:2022
01-april-2022
Lepila - Polaganje talnih oblog, lesenih talnih oblog, izravnalnih mas in ploščic -
Specifikacija velikosti zobatih plazen (ISO/DIS 6076:2022)
Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles -
Specification of trowel notch sizes (ISO/DIS 6076:2022)
Klebstoffe - Einbau von Bodenbelägen, Holzböden, Spachtelmassen und Fliesen -
Festlegung von Zahnspachtelgrößen (ISO/DIS 6076:2022)
Adhésifs - Pose de revêtements de sol, planchers en bois, ragréages et carrelages -
Spécifications des tailles des crans des peignes et spatules (ISO/DIS 6076:2022)
Ta slovenski standard je istoveten z: prEN ISO 6076
ICS:
83.180 Lepila Adhesives
oSIST prEN ISO 6076:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 6076:2022

---------------------- Page: 2 ----------------------
oSIST prEN ISO 6076:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 6076
ISO/TC 61/SC 11 Secretariat: JISC
Voting begins on: Voting terminates on:
2022-01-31 2022-04-25
Adhesives — Installation of floor coverings, wood flooring,
levelling compounds and tiles — Specification of trowel
notch sizes
ICS: 83.180
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 6076:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022

---------------------- Page: 3 ----------------------
oSIST prEN ISO 6076:2022
ISO/DIS 6076:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2022 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 6076:2022
ISO/DIS 6076:2022(E)
Contents  Page
Foreword .iv
Introduction .v
1  Scope .1
2  Normative references .1
3  Terms and definitions .1
4  Shapes . 2
5  Tolerances . 3
6  Material. 3
7  Labelling .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 21368:2023(Main)
Adhesives - Guidelines for the fabrication of adhesively bonded structures and reporting procedures suitable for the risk evaluation of such structures (ISO 21368:2022)
EN ISO 21368:2023

This document provides guidelines describing the adhesive bonding quality requirements suitable for use by adhesive user-
companies utilizing adhesive bonding as a means of fabrication. In particular, the guidelines define various approaches to meeting
quality requirements for fabrication and reporting procedures, both in workshops and on site. These guidelines aim to convey the
importance of maintaining quality standards in fabrication and reporting procedures, keeping records and thus enabling
documentation to provide the basis for risk evaluation of adhesively bonded structures in service and in use.
These guidelines have been prepared such that:
a) they are independent of the type of adhesively bonded structure;
b) they are independent of adhesive user-companies’ and suppliers’ product recommendations;
c) they define the quality requirements for adhesive bonding in terms of fabrication and reporting procedures, both in workshops and
on site;
d) they can be used as the basis for risk evaluation of adhesively bonded structures in service and in use;
e) they can be used as a basis for assessing a fabricator's capability to produce adhesively bonded structures fulfilling specified
quality requirements when they are detailed in one or more of the following:
— a contract between the parties involved;
— an application standard;
— a regulatory statement.
The guidelines contained within this document can be adopted in full or selectively chosen by the adhesive user to suit the structure
concerned. The guidelines provide a flexible framework for the control of adhesive bonding activities in the following cases.
Case 1
The provision of specific requirements for adhesive bonding in contracts that require the adhesive user to have a quality system other
than ISO 9001.
Case 2
The provision of specific requirements for adhesive bonding as guidance to an adhesive user developing a quality system.
Case 3
The provision of specific requirements for references in application standards that uses adhesive bonding as part of its requirements
or in a contract between relevant parties.
Case 4
The provision of a framework for fabrication and reporting procedures to a quality standard, suitable in particular as a basis for the risk
evaluation of adhesively bonded structures

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    108 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 302-8:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 8: Static load test of multiple bond line specimens in compression shear
EN 302-8:2023

This document specifies a method of determining the ability of adhesive bonds to resist static load. It is applicable to adhesives used in load bearing timber structures.
It is suitable for the following applications:
a)   for assessing the compliance of adhesives according to EN 301, EN 15425 and EN 16254;
b)   for assessing the suitability and quality of adhesives for load-bearing timber structures;
c)   for assessing the effect on the bond strength resulting from constant load at different climate conditions.
This method is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design, and does not necessarily represent the performance of the bonded member in service.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15425:2023(Main)
Adhesives - One component polyurethane (PUR) for load-bearing timber structures - Classification and performance requirements
EN 15425:2023

This document establishes a classification for one component polyurethane (PUR) adhesives according to their suitability for use in load-bearing timber products in defined climatic exposure conditions; it specifies performance requirements for such adhesives for the factory manufacture or factory like manufacturing of load-bearing timber products only.
It also classifies "adhesive lines" where all the products within the line have almost identical physical/chemical properties and gluing performance, but different reactivity.
This document only specifies the performance of adhesives for use in an environment corresponding to the defined conditions.
The performance requirements of this document apply to the adhesives only, not to the manufactured timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) nor the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. such as acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for the use of adhesive manufacturers and for the use in timber products bonded with adhesives, to assess or control the quality of adhesives. The requirements apply to the type testing of the adhesives. Production control activities are outside the scope of this document.
Adhesives meeting the requirements of this document are adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.
This document does not address the classification and use of adhesives in combination with the spraying of water before or during the bonding process; see informative Annex C of this document.
This does neither allow nor forbid the use of adhesives in combination with spraying of water.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 302-4:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 4: Determination of the effects of wood shrinkage on the shear strength
EN 302-4:2023

This document specifies a method for determining the influence of shear strength in crosswise gluing by wood shrinkage under drying conditions.
It is suitable for the following applications:
a)   for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b)   for assessing the suitability and quality of adhesives for load-bearing timber structures;
c)   for determining if the adhesive is capable of withstanding stresses due to wood shrinkage without unacceptable loss of strength.
This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This test is carried out on Norway spruce (Picea abies L.).
This method is not intended for use to provide numerical design data and does not necessarily represent the performance of the bonded member in service.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 302-2:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 2: Determination of resistance to delamination
EN 302-2:2023

This document specifies a method for determining the resistance to delamination in glue lines.
It is suitable for the following applications:
a)   for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b)   for assessing the suitability and quality of adhesives for load-bearing timber structures;
c)   for comparing the effects on the bond strength resulting from the choice of bonding conditions, from different climatic conditioning and from the treatment of the test pieces before and after bonding.
This test is not applicable for modified and stabilized wood with strongly reduced swelling and shrinkage properties, such as acetylated wood, heat-treated wood and polymer impregnated wood.
This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 302-6:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 6: Determination of the minimum pressing time under referenced conditions
EN 302-6:2023

This document specifies a method of determining the minimum pressing time for two glue line thicknesses, close contact glue line and 0,3 mm thick glue line (for gap filling adhesive 1,0 mm), at three temperatures. It is applicable to adhesives used in load- bearing timber structures.
This document is only intended for obtaining a reliable base of comparison of pressing time between adhesives. The method gives results that cannot be applied to the safe manufacture of timber structures without modifications for the influences of timber density/absorbency, moisture content, factory temperature and relative air humidity.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 302-7:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 7: Determination of the working life under referenced conditions
EN 302-7:2023

This document specifies a method for determining the working life for adhesives mixed with hardener for load-bearing timber structures, by a viscosity test.
This method is not suitable for determining the working life of a multi-component adhesive whose actual working life is very short.
This document is only intended for obtaining a reliable basis for comparison between adhesives. The method gives results which cannot be applied to the safe manufacture of timber structures without modifications for the influences of factory temperature and relative air humidity.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 302-5:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 5: Determination of maximum assembly time under referenced conditions
EN 302-5:2023

This document specifies a laboratory method of determining the maximum assembly time at two spread rate levels in standard atmosphere [20/65].
This document is intended for obtaining a reliable base of comparison of the maximum assembly time between adhesives at referenced conditions.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16254:2023(Main)
Adhesives - Emulsion polymer isocyanate (EPI) for load-bearing timber structures - Classification and performance requirements
EN 16254:2023

This document establishes a classification for emulsion polymerised isocyanate (EPI) adhesives according to their suitability for use in load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the industrial manufacture of load-bearing timber products only.
The performance requirements of this document apply to the adhesives only, not to the timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) nor the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. such as acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for the use of adhesive manufacturers and for the use in timber products bonded with adhesives, to assess or control the quality of adhesives. This document only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions.
Such an adhesive meeting the requirements of this document for its type is adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 301:2023(Main)
Adhesives, phenolic and aminoplastic, for load-bearing timber structures - Classification and performance requirements
EN 301:2023

This document establishes a classification for phenolic and aminoplastic polycondensation adhesives according to their suitability for use for load-bearing timber structures in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing conditions of load-bearing timber structures only.
This document only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions.
The performance requirements of this document apply to the adhesive only, not to the timber structure. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) nor the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. such as acetylated wood, heat treated wood and polymer impregnated wood.
This document is primarily intended for the use of adhesive manufacturers and for the use in timber structures bonded with adhesives, to assess or control the quality of adhesives. The requirements apply to the type testing of the adhesives. Production control activities are outside the scope of this document.
Adhesives meeting the requirements of this document are adequate for use in a load-bearing timber structures, provided that the bonding process has been carried out according to an appropriate product standard.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day