SIST EN ISO 20433:2013
(Main)Leather - Tests for colour fastness - Colour fastness to crocking (ISO 20433:2012)
Leather - Tests for colour fastness - Colour fastness to crocking (ISO 20433:2012)
This International Standard specifies a method for determining the amount of colour transferred from the surface of coloured leather to other surfaces by rubbing with a white cotton cloth. Two tests are carried out, one with a dry rubbing cloth and one with a wet rubbing cloth. The method is applicable to all types of coloured leather. Since after-treatments of the leather as well as surface finishes can affect the degree of colour transfer, the test can be made before and/or after such treatments.
Leder - Farbechtheitsprüfungen - Farbechtheit gegen Reiben (ISO 20433:2012)
Diese Internationale Norm legt ein Prüfverfahren zur Bestimmung der Farbmenge fest, die von der Oberfläche von farbigem Leder auf andere Oberflächen durch Reiben mit einem weißen Baumwollgewebe übertragen wird.
Zwei Prüfungen werden durchgeführt, eine mit einem trockenen und eine mit einem nassen Reibgewebe.
Das Verfahren gilt für alle Typen von farbigem Leder. Da sowohl Nachbehandlungen von Leder als auch Zurichtungen der Oberfläche den Grad der Farbübertragung beeinflussen können, kann die Prüfung vor und/oder nach diesen Behandlungen durchgeführt werden.
Cuir - Essais de solidité des coloris - Solidité des coloris au dégorgement par frottement (ISO 20433:2012)
La présente Norme internationale spécifie une méthode permettant de déterminer la quantité de couleur transférée de la surface d'un cuir coloré à d'autres surfaces, par frottement au moyen d'une étoffe en coton blanc.
Deux essais sont réalisés: l'un avec une étoffe de frottement à sec et l'autre avec une étoffe de frottement humide.
Cette méthode s'applique à tous les types de cuir coloré. Étant donné que les post-traitements du cuir ainsi que les apprêts peuvent avoir une incidence sur le transfert de la couleur, l'essai peut être effectué avant et/ou après ces traitements.
Usnje - Preskušanje obstojnosti barve - Obstojnost barve proti drgnjenju (ISO 20433:2012)
Ta mednarodni standard določa metodo za določevanje količine barve, ki se prenese s površine barvnega usnja na druge površine pri drgnjenju z belo bombažno krpo. Izvedeta se dva preskusa: eden s suho krpo za drgnjenje in eden z mokro krpo za drgnjenje. Ta metoda se uporablja se za vse vrste barvnega usnja. Ker lahko naknadna in površinska obdelava usnja vpliva na stopnjo prenosa barve, se lahko preskus izvede pred in/ali po takšnem postopku.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 20433:2013
01-november-2013
Usnje - Preskušanje obstojnosti barve - Obstojnost barve proti drgnjenju (ISO
20433:2012)
Leather - Tests for colour fastness - Colour fastness to crocking (ISO 20433:2012)
Leder - Farbechtheitsprüfungen - Farbechtheit gegen Reiben (ISO 20433:2012)
Cuir - Essais de solidité des coloris - Solidité des coloris au dégorgement par frottement
(ISO 20433:2012)
Ta slovenski standard je istoveten z: EN ISO 20433:2012
ICS:
59.140.30 Usnje in krzno Leather and furs
SIST EN ISO 20433:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 20433:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 20433:2013
EUROPEAN STANDARD
EN ISO 20433
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2012
ICS 59.140.30
English Version
Leather - Tests for colour fastness - Colour fastness to crocking
(ISO 20433:2012)
Cuir - Essais de solidité des coloris - Solidité des coloris au Leder - Farbechtheitsprüfungen - Farbechtheit gegen
dégorgement par frottement (ISO 20433:2012) Reiben (ISO 20433:2012)
This European Standard was approved by CEN on 30 September 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20433:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 20433:2013
EN ISO 20433:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 20433:2013
EN ISO 20433:2012 (E)
Foreword
This document (EN ISO 20433:2012) has been prepared by Technical Committee CEN/TC 289 “Leather” the
secretariat of which is held by UNI, in collaboration with IULTCS “International Union of Leather Technologists
and Chemists Societies".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the
latest by April 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 20433:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 20433:2013
INTERNATIONAL ISO
STANDARD 20433
IULTCS/IUF
452
Second edition
2012-10-01
Leather — Tests for colour fastness —
Colour fastness to crocking
Cuir — Essais de solidité des coloris — Solidité des coloris au
dégorgement par frottement
Reference number
ISO 20433:2012(E)
IULTCS/IUF 452:2012(E)
©
ISO 2012
---------------------- Page: 7 ----------------------
SIST EN ISO 20433:2013
ISO 20433:2012(E)
IULTCS/IUF 452:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 20433:2013
ISO 20433:2012(E)
IULTCS/IUF 452:2012(E)
Contents Page
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Apparatus and materials. 2
5 Test specimens . 2
6 Procedure . 2
7 Evaluation . 2
8 Precision . 3
9 Test report . 3
Annex A (informative) Apparatus and materials . 4
Bibliography . 5
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 20433:2013
ISO 20433:2012(E)
IULTCS/IUF 452:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 20433 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 289, Leather, in collaboration with the Fastness Tests Commission of the International Union of
Leather Te
...
SLOVENSKI STANDARD
oSIST prEN ISO 20433:2011
01-september-2011
Usnje - Preskušanje obstojnosti barve - Obstojnost barve proti drgnjenju (ISO/DIS
20433:2011)
Leather - Tests for colour fastness - Colour fastness to crocking (ISO/DIS 20433:2011)
Leder - Farbechtheitsprüfungen - Farbechtheit gegen Reiben (ISO/DIS 20433:2011)
Cuir - Essais de solidité des coloris - Solidité des coloris au dégorgement par frottement
(ISO/DIS 20433:2011)
Ta slovenski standard je istoveten z: prEN ISO 20433
ICS:
59.140.30 Usnje in krzno Leather and furs
oSIST prEN ISO 20433:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 20433:2011
---------------------- Page: 2 ----------------------
oSIST prEN ISO 20433:2011
EUROPEAN STANDARD
DRAFT
prEN ISO 20433
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2011
ICS 59.140.30
English Version
Leather - Tests for colour fastness - Colour fastness to crocking
(ISO/DIS 20433:2011)
Cuir - Essais de solidité des coloris - Solidité des coloris au Leder - Farbechtheitsprüfungen - Farbechtheit gegen
dégorgement par frottement (ISO/DIS 20433:2011) Reiben (ISO/DIS 20433:2011)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 289.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 20433:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 20433:2011
prEN ISO 20433:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 20433:2011
prEN ISO 20433:2011 (E)
Foreword
This document (prEN ISO 20433:2011) has been prepared by Technical Committee CEN/TC 289 “Leather”
the secretariat of which is held by UNI, in collaboration with IULTCS “International Union of Leather
Technologists and Chemists Societies".
This document is currently submitted to the parallel Enquiry.
3
---------------------- Page: 5 ----------------------
oSIST prEN ISO 20433:2011
---------------------- Page: 6 ----------------------
oSIST prEN ISO 20433:2011
DRAFT INTERNATIONAL STANDARD ISO/DIS 20433
IULTCS/IUF 452
Secretariat: IULTCS
Voting begins on Voting terminates on
2011-05-19 2011-10-19
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Leather — Tests for colour fastness — Colour fastness to
crocking
Cuir — Essais de solidité des coloris — Solidité des coloris au dégorgement par frottement
[Revision of first edition (ISO 20433:2005)]
ICS 50.140.30
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the European Committee for Standardization (CEN), and
processed under the CEN-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
This draft International Standard is submitted to all ISO member bodies for voting, as a
standard prepared by an international standardizing body in accordance with Council
Resolution 42/1999. The proposer, International Union of Leather Technologists and Chemists
(Commission IUF, IULTCS), has been recognized by the ISO Council as an international
standardizing body for the purpose of Council Resolution 42/1999.
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE REFERRED TO
AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO WHICH
REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY
ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
© International Organization for Standardization, 2011
---------------------- Page: 7 ----------------------
oSIST prEN ISO 20433:2011
ISO/DIS 20433
IULTCS/IUF 452
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be reproduced,
stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or
otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s member
body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 20433:2011
ISO/DIS 20433
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Principle.1
4 Apparatus and materials.1
5 Test specimens.2
6 Procedure.2
7 Evaluation .2
8 Precision .3
9 Test report.3
Annex A (informative) Apparatus and materials.4
A.1 Crockmeter.4
A.2 Rubbing cloth.4
A.3 Abnormal crock images.4
Bibliography.5
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
oSIST prEN ISO 20433:2011
ISO/DIS 20433
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.