SIST EN ISO 407:2005
(Main)Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2004)
Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2004)
ISO 407:2004 concerns pin-index yoke-type valve connections for small medical gas cylinders, with a maximum working pressure (filling pressure at 15 °C) of 200 bar. This type of connection is typically used for small cylinders (5 l or below). In some cases, it may be used for larger cylinders. In this latter case, consideration shall be given to the need for valve protection.
It specifies:
basic dimensions;
requirements for alternative designs of the yoke-type valve connections;
dimensions and positions for the holes and pins for the outlet connections.
It also specifies the dimensions and positions for the holes and pins for the outlet connections for certain gases and gas mixtures.
ISO 407:2004 applies to small medical gas cylinders used for patient care, including therapeutic, diagnostic and prophylactic applications, in hospitals and for emergency treatment.
Kleine Gasflaschen für die medizinische Anwendung - Ventilseitenstutzen mit Anschlussbügel nach dem Pin-Index-System (ISO 407:2004)
Diese Internationale Norm gilt für Bügelverschlüsse nach dem Pin-Index System für Gasflaschen für die medizinische Anwendung, mit einem maximalen Arbeitsdruck bei 15 °C von 250 bar.
Sie legt:
3 Grundmaße;
3 Anforderungen für alternative Konstruktionen von Bügelventilverschlüssen;
3 Maße und Anordnungen der Passlöcher und -stifte für die Anschlussverbindungen
fest.
Sie legt auch die Maße und Anordnungen der Passlöcher und -stifte für die Anschlussverbindungen der in Ta-
belle 1 enthaltenen Gase und Gasgemische fest.
Diese Verschlüsse gelten für den medizinischen Gebrauch von kleinen Gasflaschen für die Krankenpflege, einschließlich therapeutischer, diagnostischer und prophylaktischer Anwendung, in Krankenhäusern und für Notfälle.
Petites bouteilles a gaz médicaux - Raccords de robinets du type a étrier avec ergots de sécurité (ISO 407:2004)
L'ISO 407:2004 traite des raccords de robinets du type à étrier avec ergots de sécurité, destinés aux petites bouteilles à gaz médicaux ayant une pression maximale de travail (pression de remplissage à 15 °C) de 200 bar. Ce type de raccord est essentiellement utilisé pour les petites bouteilles (de 5 l ou moins). Parfois, il peut être utilisé pour des bouteilles plus grandes. Dans ce cas, l'attention doit être portée sur la nécessité d'une protection du robinet.
Elle spécifie
les dimensions de base des raccords,
les exigences requises des variantes de construction des raccords de robinets du type à étrier, et
les dimensions et positions des trous et des ergots des sorties de raccords.
Elle spécifie également les dimensions et les positions des trous et des ergots des sorties de raccords pour les gaz et les mélanges de gaz donnés dans le Tableau 1.
L'ISO 407:2004 est applicable aux petites bouteilles à gaz médicaux utilisées pour des soins aux malades, comportant des applications thérapeutiques, diagnostiques et prophylactiques, dans les hôpitaux et pour les traitements d'urgence.
Male plinske jeklenke za uporabo v medicini - Ventilski priključni nastavki po sistemu pin-index (ISO 407:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 407:2005
01-januar-2005
1DGRPHãþD
SIST EN 850:1999
SIST EN 850:1999/A1:2002
SIST EN 850:1999/AC:1999
0DOHSOLQVNHMHNOHQNH]DXSRUDERYPHGLFLQL9HQWLOVNLSULNOMXþQLQDVWDYNLSR
VLVWHPXSLQLQGH[ ,62
Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2004)
Kleine Gasflaschen für die medizinische Anwendung - Ventilseitenstutzen mit
Anschlussbügel nach dem Pin-Index-System (ISO 407:2004)
Petites bouteilles a gaz médicaux - Raccords de robinets du type a étrier avec ergots de
sécurité (ISO 407:2004)
Ta slovenski standard je istoveten z: EN ISO 407:2004
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
SIST EN ISO 407:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 407:2005SIST EN ISO 407:2005
---------------------- Page: 2 ----------------------
SIST EN ISO 407:2005SIST EN ISO 407:2005
EUROPEAN STANDARD
EN ISO 407
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2004
ICS 11.040.10 Supersedes EN 850:1996
English version
Small medical gas cylinders - Pin-index yoke-type valve
connections (ISO 407:2004)
Petites bouteilles à gaz médicaux - Raccords de robinets Kleine Gasflaschen für die medizinische Anwendung -
du type à étrier avec ergots de sécurité (ISO 407:2004) Ventilseitenstutzen mit Anschlussbügel nach dem Pin-
Index-System (ISO 407:2004)
This European Standard was approved by CEN on 10 September 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 407:2004: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 407:2005SIST EN ISO 407:2005
EN ISO 407:2004 (E)
Foreword
This document (EN ISO 407:2004) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 "Transportable gas cylinders",
the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2005, and conflicting national standards
shall be withdrawn at the latest by May 2005.
This document supersedes EN 850:1996.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 407:2004 has been approved by CEN as EN ISO 407:2004 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 407:2005SIST EN ISO 407:2005
INTERNATIONAL ISO
STANDARD 407
Third edition
2004-11-01
Small medical gas cylinders — Pin-index
yoke-type valve connections
Petites bouteilles à gaz médicaux — Raccords de robinets du type à
étrier avec ergots de sécurité
Reference number
ISO 407:2004(E)
©
ISO 2004
---------------------- Page: 5 ----------------------
SIST EN ISO 407:2005SIST EN ISO 407:2005
ISO 407:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 407:2005SIST EN ISO 407:2005
ISO 407:2004(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Valve. 1
4 Yoke. 2
5 Basic dimensions. 2
5.1 General. 2
5.2 Pin-index yoke-type valve body . 3
5.3 Single-pin yoke-type valve connection system . 4
5.4 Two-pin yoke-type valve connection system with the pins in a single row . 4
5.5 Two-pin yoke-type valve connection system with the pins in a double row . 5
5.6 Basic dimensions. 5
6 Requirements for alternative designs of yoke-type valve connections. 6
6.1 Requirements for the design of the connecting yoke. 6
6.2 Examples of alternative construction for the connecting yoke . 7
7 Dimensions and positions of the holes and pins for yoke-type valve connections. 9
7.1 General. 9
7.2 Outlet connection with single-pin system. 9
7.3 Outlet connections with two-pin/single-row system. 10
7.4 Outlet connection with two-pin/double-row system . 20
© ISO 2004 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 407:2005SIST EN ISO 407:2005
ISO 407:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 407 was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2, Cylinder
fittings.
This third edition cancels and replaces the second edition (ISO 407:1991), which has been technically revised.
iv © ISO 2004 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 407:2005SIST EN ISO 407:2005
INTERNATIONAL STANDARD ISO 407:2004(E)
Small medical gas cylinders — Pin-index yoke-type valve
connections
1 Scope
This International Standard concerns pin-index yoke-type valve connections for small medical gas cylinders,
with a maximum working pressure (filling pressure at 15 °C) of 200 bar. This type of connection is typically
used for small cylinders (5 l or below). In some cases, it may be used for larger cylinders. In this latter case,
consideration shall be given to the need for valve protection.
It specifies:
basic dimensions;
requirements for alternative designs of the yoke-type valve connections;
dimensions and positions for the holes and pins for the outlet connections.
It also specifies the dimensions and positions for the holes and pins for the outlet connections for the gases
and gas mixtures given in Table 1.
This International Standard applies to small medical gas cylinders used for patient care, including therapeutic,
diagnostic and prophylactic applications, in hospitals and for emergency treatment.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 32:1977, Gas cylinders for medical use — Marking for identification of content
3 Valve
Each small medical gas cylinder can be fitted with a yoke valve (see Clause 5). The yoke valve shall have
location holes of the dimensions and in the positions indicated in Clause 7 for the appropriate gas or gas
mixture.
The name or chemical symbol of the gas or gas mixture shall be clearly and indelibly stamped on the valve.
© ISO 2004 – All rights reserved 1
---------------------- Page: 9 ----------------------
SIST EN ISO 407:2005SIST EN ISO 407:2005
ISO 407:2004(E)
Table 1 — Al
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.