SIST EN ISO 13260:2011

Thermoplastics piping systems for non-pressure underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading (ISO 13260:2010)

ISO 13260:2010 specifies two methods for testing pipes and fittings or joints for plastics piping systems intended for use in underground drainage and sewerage systems for their resistance to deformation and leakage, when subjected to sustained external loading in conjunction with the passage of hot water.

Kunststoff-Rohrleitungssysteme aus Thermoplasten für erdverlegte Abwasserkanäle und -leitungen - Prüfverfahren zur Bestimmung der Widerstandsfähigkeit gegen Temperaturwechsel und gleichzeitige äußere Belastung (ISO 13260:2010)

Diese Internationale Norm legt zwei Verfahren zur Prüfung von Rohren und Formstücken oder Verbindungen für Kunststoff-Rohrleitungssysteme fest, die in erdverlegten Abwasserkanal- und -leitungssystemen verwen-det werden, auf deren Verformungsbeständigkeit und Dichtheit bei anhaltender äußerer Belastung in Verbin-dung mit dem gleichzeitigen Durchlauf von Warmwasser. Verfahren A umfasst die Temperaturwechselbeanspruchung durch abwechselnden Durchlauf von Warm- und Kaltwasser und ist anwendbar für Rohre und zugehörige Formstücke mit einem mittleren Außendurchmesser dem ≤ 190 mm. Verfahren B umfasst nur den Durchlauf von Warmwasser, ausgenommen in den für die Messung der Innen-durchbiegung vorgeschriebenen Intervallen, und ist anwendbar für Rohre und zugehörige Formstücke mit einem mittleren Außendurchmesser 190 mm < dem ≤ 510 mm.

Systèmes de canalisations thermoplastiques pour branchements et collecteurs d'assainissement enterrés sans pression - Méthode d'essai de la résistance à un cycle de température et de charge externe combinés (ISO 13260:2010)

L'ISO 13260:2010 sp�cifie deux m�thodes d'essai de tubes et de raccords ou d'assemblages de syst�mes de canalisations en mati�res plastiques pour branchements et collecteurs d'assainissement enterr�s afin de v�rifier leur r�sistance � la d�formation et aux fuites lorsqu'ils sont soumis � une charge ext�rieure permanente conjugu�e avec le passage d'eau chaude.

Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Preskusna metoda za ugotavljanje odpornosti proti kombinaciji izmenične temperaturne in sočasne zunanje obremenitve (ISO 13260:2010)

ISO 13260:2010 določa dve metodi za preskušanje cevi in fitingov ali spojev za polimerne cevne sisteme, namenjene uporabi v sistemih za odpadno vodo in kanalizacijo, za ugotavljanje odpornosti proti deformaciji in puščanju pri stalni zunanji obremenitvi v povezavi s prehajanjem vroče vode.

General Information

• Status: Published
• Public Enquiry End Date: 19-May-2011
• Publication Date: 08-Nov-2011
• ICS: 23.040.05 - Pipeline and its parts for external sewage systems
• ICS: 93.030 - External sewage systems
• Technical Committee: PCV - Plastic pipes, fittings and valves
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 28-Oct-2011
• Due Date: 02-Jan-2012
• Completion Date: 09-Nov-2011
• Ref Project: EN ISO 13260:2011 - Thermoplastics piping systems for non-pressure underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading (ISO 13260:2010)

Relations

• Replaces: SIST EN 1437:2003 - Plastics piping systems - Piping systems for underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading
• Effective Date: 01-Dec-2011
• Amended By: SIST EN ISO 13260:2011/A1:2017 - Thermoplastics piping systems for non-pressure underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading - Amendment 1 (ISO 13260:2011/Amd 1:2017)
• Effective Date: 01-Nov-2017

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 13260:2011
01-december-2011
1DGRPHãþD
SIST EN 1437:2003
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DRGSDGQRYRGRLQNDQDOL]DFLMRNLGHOXMHMR
SRWHåQRVWQHPSULQFLSXLQVRSRORåHQLY]HPOMR3UHVNXVQDPHWRGD]D
XJRWDYOMDQMHRGSRUQRVWLSURWLNRPELQDFLMLL]PHQLþQHWHPSHUDWXUQHLQVRþDVQH
]XQDQMHREUHPHQLWYH,62
Thermoplastics piping systems for non-pressure underground drainage and sewerage -
Test method for resistance to combined temperature cycling and external loading (ISO
13260:2010)
Kunststoff-Rohrleitungssysteme aus Thermoplasten für erdverlegte Abwasserkanäle und
-leitungen - Prüfverfahren zur Bestimmung der Widerstandsfähigkeit gegen
Temperaturwechsel und gleichzeitige äußere Belastung (ISO 13260:2010)
Systèmes de canalisations thermoplastiques pour branchements et collecteurs
d'assainissement enterrés sans pression - Méthode d'essai de la résistance à un cycle
de température et de charge externe combinés (ISO 13260:2010)
Ta slovenski standard je istoveten z: EN ISO 13260:2011
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN ISO 13260:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 13260:2011

---------------------- Page: 2 ----------------------

SIST EN ISO 13260:2011


EUROPEAN STANDARD
EN ISO 13260

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2011
ICS 93.030; 23.040.20; 91.140.80; 23.040.45 Supersedes EN 1437:2002
English Version
Thermoplastics piping systems for non-pressure underground
drainage and sewerage - Test method for resistance to
combined temperature cycling and external loading (ISO
13260:2010)
Systèmes de canalisations thermoplastiques pour Kunststoff-Rohrleitungssysteme aus Thermoplasten für
branchements et collecteurs d'assainissement enterrés erdverlegte Abwasserkanäle und -leitungen - Prüfverfahren
sans pression - Méthode d'essai de la résistance à un cycle zur Bestimmung der Widerstandsfähigkeit gegen
de température et de charge externe combinés (ISO Temperaturwechsel und gleichzeitige äußere Belastung
13260:2010) (ISO 13260:2010)
This European Standard was approved by CEN on 11 August 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13260:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 13260:2011
EN ISO 13260:2011 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 13260:2011
EN ISO 13260:2011 (E)
Foreword
The text of ISO 13260:2010 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings
and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 13260:2011 by Technical Committee CEN/TC 155 “Plastics piping systems and ducting
systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2012, and conflicting national standards shall be withdrawn at
the latest by March 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1437:2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 13260:2010 has been approved by CEN as a EN ISO 13260:2011 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 13260:2011

---------------------- Page: 6 ----------------------

SIST EN ISO 13260:2011

INTERNATIONAL ISO
STANDARD 13260
First edition
2010-06-15


Thermoplastics piping systems for non-
pressure underground drainage and
sewerage — Test method for resistance
to combined temperature cycling and
external loading
Systèmes de canalisations thermoplastiques pour branchements et
collecteurs d'assainissement enterrés sans pression — Méthode d'essai
de la résistance à un cycle de température et de charge externe
combinés




Reference number
ISO 13260:2010(E)
©
ISO 2010

---------------------- Page: 7 ----------------------

SIST EN ISO 13260:2011
ISO 13260:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 13260:2011
ISO 13260:2010(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Principle.1
4 Apparatus.2
5 Test piece.6
6 Conditioning .6
7 Procedure.7
7.1 Test piece embedment and loading .7
7.2 Exposure to hot water.8
7.3 Assessment.9
8 Calculation and expression of results .10
9 Test report.10
Annex A (informative) Recommended requirements .12

© ISO 2010 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 13260:2011
ISO 13260:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13260 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the
transport of fluids, Subcommittee SC 1, Plastics pipes and fittings for soil, waste and drainage (including land
drainage).
iv © ISO 2010 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 13260:2011
INTERNATIONAL STANDARD ISO 13260:2010(E)

Thermoplastics piping systems for non-pressure underground
drainage and sewerage — Test method for resistance to
combined temperature cycling and external loading
1 Scope
This International Standard specifies two methods for testing pipes and fittings or joints for plastics piping
systems intended for use in underground drainage and sewerage systems for their resistance to deformation
and leakage, when subjected to sustained external loading in conjunction with the passage of hot water.
Method A involves temperature cycling, by passing hot water and cold water alternately, and is applicable to
pipes and associated fittings having a mean outside diameter d u 190 mm.
em
Method B involves passing hot water only, except at intervals specified for measurement of internal
deflection, and is applicable to pipes and associated fittings having a mean outside diameter
190 mm < d u 510 mm.
em
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 48, Rubber, vulcanized or thermoplastic — Determination of hardness (hardness between 10 IRHD and
100 IRHD)
3 Principle
A test piece comprising a pipe or an assembly of pipe(s) and fitting(s) is placed on a 100 mm gravel bed and
covered with gravel to 600 mm above the crown of the pipe confined by a box of specified dimensions.
Depending on the nominal size of the largest pipe or joint under test, a constant vertical load is applied via the
gravel and either a specified number of cycles of hot and cold water or just hot water is passed through the
test piece. The deformation of the test piece, as indicated by vertical deflection or internal diametric
compression, is measured.
For sizes having a mean outside diameter d u 190 mm, hot and cold water is passed through the test piece
em
and air may be blown through the test piece during the intervals between stages (Method A).
For pipes with a mean outside diameter 190 < d u 510 mm a constant flow of hot water is passed through
em
the test piece (Method B).
Vertical deflection of the test piece is measured. The test piece is checked at the end of the test for cracking,
for local deflection in the bottom of the main channel and for leakage at the joints.
© ISO 2010 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 13260:2011
ISO 13260:2010(E)
It is assumed that the following parameters are set by the referring standard:
a) if appropriate, the limits of the temperature of the water flowing out (see 7.2.2);
b) if appropriate, the duration of the flow (see 7.2.2);
c) the percentage, x, of d for the calculation of the diameter of the hard ball, in accordance with 7.3.3.
i
4 Apparatus
4.1 Gravel-filled box, to accommodate a test piece as shown in Figures 1, 2 and 3, with dimensions
depending on the size of the test piece as given in Table 1 and with a horizontal base.
Dimensions in millimetres

Key
1 loading device 8 filling material
2 box 9 test sample
3 loading plate 10 outlet hot water sensor (for Method B only)
4 cold water sensor 11 water outlet (sealable)
5 inlet hot water sensor
a
Air inlet.
6 upper surface sensor
b
Hot water inlet.
7 cold water spray (sparge pipe)
c
Cold water inlet.
Figure 1 — Typical box loading test (BLT) apparatus
2 © ISO 2010 – All rights reserved

---------------------- Page: 12 ----------------------

SIST EN ISO 13260:2011
ISO 13260:2010(E)
Table 1 — Box dimensions
Dimensions in millimetres
a
Mean outside Minimum length
Inside box width
diameter pipe/fitting of box
d l
l
em 2
1
600 < l u 990
Method A u 190
1 200
1
190 < d u 205 790 < l u 1 005 1 300
em 1
205 < d u 255 805 < l u 1 055 1 500
em 1
255 < d u 320 855 < l u 1 120 1 500
Method B
em 1
320 < d u 410 920 < l u 1 210 1 500
em 1
410 < d u 510 1 010 < l u 1 310 1 500
em 1
a
The inside box width shall be determined on the basis of a clearance of
(350 ± 100) mm between the side of the pipe/fitting and the side of the box. The inside box
width should be adjustable by closing the gap using plywood sheeting or brickwork as a
spacer.

The inside walls of the box shall be vertical ±3 mm and shall have an inside smooth surface, e.g. plywood or
flat sheet.
The box shall be constructed and reinforced such that, when under load, it shall not deflect more than 3,0 mm
at any point.
The pipe line shall pass through the walls of the box via holes sealed in such a way as to impose minimal
restraint on the assembly (see Clause 5), e.g. by flexible closed cell sponge collars. The test assembly of
pipes or pipes and fittings shall be placed with a fall of between 1:100 and 1:75 to the horizontal base, such
that in the case of Method A, conditions alternate between discharges of hot and cold water or in the case of
Method B, water at a constant temperature can be passed through the assembly while it is subjected to a
constant force acting through the gravel.
The box shall be constructed such that it can accommodate a total height of gravel of 600 mm above the
crown of the pipe.
© ISO 2010 – All rights reserved 3

---------------------- Page: 13 ----------------------

SIST EN ISO 13260:2011
ISO 13260:2010(E)
Dimensions in millimetres and prior to load being applied

Figure 2 — Main dimensions of the box
The gravel shall be classified in accordance with Table 2, shall have a surface texture in accordance with
Table 3, with granular composition within the range shown in Figure 3 and shall conform to the requirements
of Table 4.

Key
X particle size, in millimetres
Y cumula
...