SIST EN IEC 60230:2018
(Main)Impulse tests on cables and their accessories (IEC 60230:2018)
Impulse tests on cables and their accessories (IEC 60230:2018)
This document defines the procedure for carrying out withstand lightning and switching
impulse tests and withstand superimposed impulse test on cables and their accessories.
This document applies solely to the methods of carrying out the tests as such, independently
of the problem of selecting the test levels to be specified. The voltages pertaining to the
system on which cables and accessories are to be used are given in IEC 60183 or in the
relevant product standard.
This document specifies the following requirements:
• the characteristics and state of the test installation and those parts of the procedure which
are common to withstand tests and tests above the withstand level;
• the procedure for carrying out withstand lightning and switching impulse tests and
superimposed impulse test;
• the procedure for carrying out tests above the withstand level which is intended for
research purposes.
Stoßspannungsprüfungen an Kabeln und deren Garnituren (IEC 60230:2018)
Essais de choc des câbles et de leurs accessoires (IEC 60230:2018)
L'IEC 60230:2018 définit la procédure pour la réalisation des essais de tenue au choc de foudre et aux chocs de manœuvre et des essais de tenue au choc superposé appliqués aux câbles et de leurs accessoires.
Ce document ne s’applique qu’aux méthodes d’essai en tant que telles, indépendamment du choix des niveaux d’essai à spécifier. Les tensions associées au système sur lequel les câbles et accessoires doivent être utilisés sont indiquées dans l’IEC 60183 ou dans la norme de produit applicable.
Ce document spécifie les exigences suivantes:
- les caractéristiques et l’état de l’installation d’essai ainsi que les parties de la procédure qui sont également applicables aux essais de tenue et aux essais à niveaux supérieurs aux essais de tenue;
- la procédure pour la réalisation des essais de tenue au choc de foudre et aux chocs de manœuvre, ainsi que des essais de choc superposé;
- la procédure pour la réalisation d’essais, à des fins de recherches, à des niveaux supérieurs au niveau de tenue.
Cette deuxième édition annule et remplace la première édition parue en 1966. Cette édition constitue une révision technique.
Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente:
a) la structure de la norme tient compte du modèle actuel des normes IEC;
b) le présent document n’est plus une “Recommandation” mais une “Norme internationale”;
c) l’installation d'essai n’est plus liée uniquement aux câbles à pression de gaz et aux câbles à huile fluide;
d) des essais de tension de choc de manœuvre et des essais de tension de choc superposée ont été intégrés;
e) pour le système de mesure, la référence à l’IEC 60060-2 a été ajoutée. La référence à la méthode de l’éclateur à sphères a été intégrée dans l’Annexe B.
Impulzno preskušanje kablov in njihovega pribora (IEC 60230:2018)
Ta dokument določa postopek za preskušanje, ali kabli in njihov pribor vzdržijo udar strele in stikalni napetostni udar in ali vzdržijo superponirano impulzno preskušanje.
Ta dokument se uporablja samo za metode izvajanja preskusov samih, neodvisno od izbire stopnje preskusa, ki bo določena. Napetosti, ki so povezane s sistemom, za katerega je predvidena uporaba kablov in pribora, so podane v standardu IEC 60183 ali v ustreznem standardu za proizvod.
Ta dokument določa naslednje zahteve:
• lastnosti in stanje preskusne inštalacije in tistih delov postopka, ki so značilni za preskuse nivoja vzdržljivosti in za preskuse nad nivojem vzdržljivosti;
• postopek za izvajanje preskusa vzdržljivosti na udar strele in stikalni napetostni udar ter superponiranega impulznega preskusa;
• postopek za izvajanje preskusov nad nivojem vzdržljivosti za namene znanstvenih raziskav.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 60230:2018
01-junij-2018
1DGRPHãþD
SIST EN 60230:2002 (HD 48 S1)
Impulzno preskušanje kablov in njihovega pribora (IEC 60230:2018)
Impulse tests on cables and their accessories (IEC 60230:2018)
Stoßspannungsprüfungen an Kabeln und deren Garnituren (IEC 60230:2018)
Essais de choc des câbles et de leurs accessoires (IEC 60230:2018)
Ta slovenski standard je istoveten z: EN IEC 60230:2018
ICS:
29.060.20 Kabli Cables
SIST EN IEC 60230:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 60230:2018
---------------------- Page: 2 ----------------------
SIST EN IEC 60230:2018
EUROPEAN STANDARD EN IEC 60230
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2018
ICS 29.060.20 Supersedes EN 60230:2002
English Version
Impulse tests on cables and their accessories
(IEC 60230:2018)
Essais de choc des câbles et de leurs accessoires Stoßspannungsprüfungen an Kabeln und deren Garnituren
(IEC 60230:2018) (IEC 60230:2018)
This European Standard was approved by CENELEC on 2018-02-14. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60230:2018 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60230:2018
EN IEC 60230:2018 (E)
European foreword
The text of document 20/1769A/FDIS, future edition 2 of IEC 60230, prepared by IEC/TC 20 "Electric
cables" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 60230:2018.
The following dates are fixed:
(dop) 2018-11-14
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2021-02-14
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60230:2002.
Endorsement notice
The text of the International Standard IEC 60230:2018 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60060-2 NOTE Harmonized as EN 60060-2.
2
---------------------- Page: 4 ----------------------
SIST EN IEC 60230:2018
EN IEC 60230:2018 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60060-1 2010 High-voltage test techniques -- Part 1: EN 60060-1 2010
General definitions and test requirements
3
---------------------- Page: 5 ----------------------
SIST EN IEC 60230:2018
---------------------- Page: 6 ----------------------
SIST EN IEC 60230:2018
IEC 60230
®
Edition 2.0 2018-01
INTERNATIONAL
STANDARD
Impulse tests on cables and their accessories
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.060.20 ISBN 978-2-8322-5236-9
Warning! Make sure that you obtained this publication from an authorized distributor.
® Registered trademark of the International Electrotechnical Commission
---------------------- Page: 7 ----------------------
SIST EN IEC 60230:2018
– 2 – IEC 60230:2018 © IEC 2018
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Characteristics of the test object to be subjected to the tests . 5
5 State of the test object to be subjected to the test . 6
6 Lightning impulse voltage . 6
7 Switching impulse voltage . 6
8 Superimposed impulse voltage test . 6
8.1 General . 6
8.2 Test setup . 6
8.3 Time parameters . 7
8.4 Application of the DC voltage . 7
9 Measuring system . 7
10 Application of the impulses . 7
Annex A (informative) Tests above the withstand level . 8
A.1 General . 8
A.2 Procedure for tests above the withstand level . 8
A.2.1 General sequence of lightning-impulse tests . 8
A.2.2 Tests beyond withstand level . 8
A.2.3 Re-calibration of the generator . 8
Annex B (normative) Calibration of impulse generator . 9
B.1 General . 9
B.2 Calibration of impulse generator . 9
B.3 Application of the impulses at the level specified . 9
Annex C (normative) Test circuits for superimposed impulse voltage test . 10
C.1 General . 10
Bibliography . 12
Figure C.1 – Spark gap setup using calibrated composite measuring system capable of
measuring HVDC and impulse . 10
Figure C.2 – Blocking capacitor setup using calibrated composite measuring system
capable of measuring HVDC and impulse . 11
---------------------- Page: 8 ----------------------
SIST EN IEC 60230:2018
IEC 60230:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
IMPULSE TESTS ON CABLES AND THEIR ACCESSORIES
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60230 has been prepared by IEC technical committee 20: Electric
cables.
This second edition cancels and replaces the first edition published in 1966. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) the structure of the standard takes into account the current style of IEC standards;
b) this document is no longer a “Recommendation” but an “International Standard”;
c) the test installation is no longer related to gas-pressure and oil-filled cables only;
d) switching-impulse voltage and superimposed impulse voltage tests have been included;
e) for the measuring system the reference to IEC 60060-2 has been added. The reference to
the sphere gap method has been moved to Annex B.
---------------------- Page: 9 ----------------------
SIST EN IEC 60230:2018
– 4 – IEC 60230:2018 © IEC 2018
The text of this standard is based on the following documents:
FDIS Report on voting
20/1769A/FDIS 20/1779/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
---------------------- Page: 10 ----------------------
SIST EN IEC 60230:2018
IEC 60230:2018 © IEC 2018 – 5 –
IMPULSE TESTS ON CABLES AND THEIR ACCESSORIES
1 Scope
This document defines the procedure for carrying out withstand lightning and switching
impulse tests and withstand superimposed impulse test on cables and their accessories.
This document applies solely to the methods of carrying out the tests as such, independently
of the problem of selecting the test levels to be specified. The voltages pertaining to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.