SIST EN 50102:2001/A1:2001
(Amendment)Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
D99/171: BTTF 68-3 disbanded * Identical with EN 62262:2002 (boomerang)
Schutzarten durch Gehäuse für elektrische Betriebsmittel (Ausrüstung) gegen äußere mechanische Beanspruchungen (IK-Code)
Degrés de protection procurés par les enveloppes de matériels électriques contre les impacts mécaniques externes (code IK)
Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 50102:2001/A1:2001
01-september-2001
Degrees of protection provided by enclosures for electrical equipment against
external mechanical impacts (IK code)
Degrees of protection provided by enclosures for electrical equipment against external
mechanical impacts (IK code)
Schutzarten durch Gehäuse für elektrische Betriebsmittel (Ausrüstung) gegen äußere
mechanische Beanspruchungen (IK-Code)
Degrés de protection procurés par les enveloppes de matériels électriques contre les
impacts mécaniques externes (code IK)
Ta slovenski standard je istoveten z: EN 50102:1995/A1:1998
ICS:
...
This May Also Interest You
This standard refers to the classification of the degrees of protection provided by enclosures against external mechanical impacts when the rated voltage of the protected equipment is not greater than 72,5 kV. This standard is only applicable to enclosures of equipment where the specific standard establishes degrees of protection of the enclosure against mechanical impacts (expressed in this standard as impacts). The object of this standard is to give: the definitions for degrees of protection provided by enclosures of electrical equipment as regards protection of the equipment inside the enclosure against harmful effects of mechanical impacts; the designations for the degrees of protection; the requirements for each designation; the tests to be performed to verify that enclosures meets the requirements of this standard
- Standard11 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 62561 specifies the requirements and tests for devices intended to count the number of lightning strikes based on the current flowing in a conductor. This conductor may be part of a lightning protection system (LPS) or connected to an SPD installation or other conductors, which are not intended to conduct a significant portion of lightning currents.
LSCs for use in hazardous atmospheres, extra requirements for the components may be necessary to be taken.
NOTE In CENELEC countries, testing requirements of components for explosive atmosphere are specified in CLC/TS 50703-2.
- Standard28 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 60050-692:2017 gives the terminology used when considering the dependability and quality of service of electric power systems. The concepts are categorized according to the following sections:
- system concepts;
- operating states of electric power systems;
- failures in electric power systems;
- outages of electric power systems equipment;
- outage occurrences in electric power systems;
- state durations and availability related concepts;
- interruptions in electric power systems;
- selected customer interruption measures;
- bulk electric power system load/energy curtailments;
- bulk electric system failures and measures;
- supply performance measures.
This terminology is consistent with the terminology developed in the other specialized parts of the IEV.
It has the status of a horizontal standard in accordance with IEC Guide 108.
- Standard140 pagesEnglish and French languagesale 10% offe-Library read for×1 day
- Standard127 pagesEnglish and French languagesale 15% off
This part of IEC 62561 specifies the requirements and tests for metallic connection
components that form part of a lightning protection system (LPS). Typically, these can be
connectors, clamps, bonding and bridging components, expansion pieces and test joints.
For the purposes of this document the following connection types are considered as
connection components: exothermic, brazing, welding, clamping, crimping, seaming, screwing
or bolting.
Testing of components for an explosive atmosphere is not covered by this document.
- Standard32 pagesEnglish languagesale 10% offe-Library read for×1 day
1.1 Scope
This document specifies the main characteristics of the voltage at a network user's supply terminals in public low voltage, medium, high, and extra-high voltage AC electricity networks under normal operating conditions. This document specifies the limits or values within which the voltage characteristics can be expected to remain at any supply terminal in public European electricity networks, only.
NOTE 1 If non-public networks (e.g. residential quarters, energy communities, office centres, shopping centres) have similar end-users as public networks, it is strongly advised to apply the same requirements as for public networks.
NOTE 2 Industrial networks are excluded from the scope of EN 50160, only the connection to the supply terminals of the public network is relevant, here.
This document does not apply under abnormal operating conditions, including the following:
a) a temporary supply arrangement to keep network users supplied during conditions arising as a result of a fault, maintenance and construction work, or to minimize the extent and duration of a loss of supply.
b) in the case of non-compliance of a network user's installation or equipment with the relevant standards or with the technical requirements for connection, established either by the public authorities or the network operator, including the limits for the emission of conducted disturbances.
NOTE 4 A network user’s installation can include load and generation.
c) in exceptional situations, in particular:
1) exceptional weather conditions and other natural disasters;
2) third party interference;
3) acts by public authorities,
4) industrial actions (subject to legal requirements);
5) force majeure;
6) power shortages resulting from external events.
The voltage characteristics given in this document refer to conducted disturbances in public electric power networks. They are not intended to be used as electromagnetic compatibility (EMC) levels or product emission limits.
Power quality is related to EMC in several ways – especially because compliance with power quality requirements depends on the control of cumulative effect of electromagnetic emissions from all/multiple equipment and/or installations. Therefore, the voltage characteristics given in this document gives guidance for specifying requirements in equipment product standards and in installation standards.
NOTE 5 The performance of equipment might be impaired if it is subjected to supply conditions which are not specified in the equipment product standard.
NOTE 6 This document can be superseded in total or in part by the terms of a contract between the individual network user and the network operator.
NOTE 7 The sharing of complaint management and problem mitigation costs between the involved parties is outside the scope of EN 50160.
Measurement methods to be applied in this document are described in EN 61000 4 30.
1.2 Object
The object of this document is to define, describe and specify the characteristics of the supply voltage concerning:
a) Frequency;
b) Magnitude;
c) Waveform;
d) Symmetry of the line voltages.
This document also covers the continuous characteristics of the supply voltage and other foreseeable phenomena which may influence the voltage characteristics, such as e.g. operational communication, monitoring or measurement signals which are transmitted via power lines.
These characteristics are subject to variations during the normal operation of a supply system due to changes of load, disturbances generated by certain equipment and the occurrence of faults which are mainly caused by external events.
The characteristics vary in a manner which is random in time, with reference to any specific supply terminal, and random in location, with reference to any given instant of time. Because of these variations, the values given in this document for the characteristics can be expected to be exceeded on a small number of occasions.
[...]
- Standard53 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 60216 specifies the experimental and calculation procedures to be used for
deriving the relative temperature index of a material from experimental data obtained in
accordance with the instructions of IEC 60216-1 and IEC 60216-2. The calculation procedures
are supplementary to those of IEC 60216-3.
Guidance is also given for assessment of thermal ageing after a single fixed time and
temperature, without extrapolation.
The experimental data can in principle be obtained using destructive, non-destructive or proof
tests, although destructive tests have been much more extensively employed. Data obtained
from non-destructive or proof tests can be “censored”, in that measurement of times taken to
reach the endpoint have been terminated at some point after the median time but before all
specimens have reached end-point (see IEC 60216-1).
Guidance is given for preliminary assignment of a thermal class for an electrical insulating
material (EIM), based upon the thermal ageing performance.
While the thermal classification of an EIM is not directly related to the thermal classification of
an electrical insulation system (EIS), the thermal classification of an EIS follows the same
concepts as presented in this part of the 60216 series. The calculation procedures of this
standard apply to the determination of the thermal class of an EIS when the thermal stress is
the prevailing ageing factor.
- Standard32 pagesEnglish languagesale 10% offe-Library read for×1 day
IEC 60364-5-54:2011 addresses the earthing arrangements and protective conductors including protective bonding conductors in order to satisfy the safety of the electrical installation. This third edition cancels and replaces the second edition, published in 2002, and constitutes a technical revision. The main changes with respect to the previous edition are listed below: - clarification of the definition of protective conductor; - improved specification of mechanical characteristics of the earth electrode; - introduction of earth electrode for protection against electric shock and lighting protection; - annexes describing concrete-embedded foundation earth electrodes and soil-embedded earth electrode. IEC 60364-5-54:2011 has the status of a basic safety publication in accordance with IEC Guide 104.
This document also includes requirements regarding earthing and equipotential bonding for
information and communication technology (ICT) with the aim of:
- reducing the risk of electrical hazards for correct operation of these devices and the
information and communication technology wiring;
- providing the telecommunication systems with a reliable signal reference plane that can
improve resistance to electromagnetic interference (EMI) by reference to ISO/IEC 30129.
NOTE Examples of information and communication technology (ICT) include:
- DC supply networks (and systems) for supplying power to ICT equipment within a building;
- star-shaped private automatic branch exchanges (PABX) or their equipment;
- local area (communication) networks (LANs);
- fire and intruder alarms communication systems;
- building automation systems, e.g. direct digital control systems;
- systems for computer-aided manufacturing (CAM) and other computer-aided services;
- broadcast and communication technology.
- Amendment4 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of IEC 60050 gives the general terminology used in environmental standardization
for electrical and electronic products and systems. It has the status of a horizontal standard in
accordance with IEC Guide 108, Guidelines for ensuring the coherency of IEC publications –
Application of horizontal standards.
This terminology is consistent with the terminology developed in the other specialized parts of
the IEV.
This horizontal standard is primarily intended for use by technical committees in the
preparation of standards in accordance with the principles laid down in IEC Guide 108.
One of the responsibilities of a technical committee is, wherever applicable, to make use of
horizontal standards in the preparation of its publications. The content of this horizontal
standard will not apply unless specifically referred to or included in the relevant publications.
- Standard61 pagesEnglish and French languagesale 10% offe-Library read for×1 day
This part of IEC 81346, published jointly by IEC and ISO, establishes general principles for the structuring of systems including structuring of the information about systems.
Based on these principles, rules and guidance are given for the formulation of unambiguous reference designations for objects in any system.
The reference designation identifies objects for the purpose of creation and retrieval of information about an object, and where realized about its corresponding component.
A reference designation labelled at a component is the key to find information about that object among different kinds of documents.
The principles are general and are applicable to all technical areas (for example mechanical engineering, electrical engineering, construction engineering, process engineering). They can be used for systems based on different technologies or for systems combining several technologies.
This document is also a horizontal publication intended for use by technical committees in preparation of publications related to reference designations in accordance with the principles laid down in IEC Guide 108.
- Standard121 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft111 pagesEnglish languagesale 10% offe-Library read for×1 day
CLC/TC 34 took decision to unlink project from LVD
- Amendment9 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft4 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.