SIST EN 40-2:2005
(Main)Lighting columns - Part 2: General requirements and dimensions
Lighting columns - Part 2: General requirements and dimensions
This document specifies the requirements and dimensions for lighting columns, brackets, base compartments, cableways and earthing terminals. It applies to post top columns not exceeding 20 m height for post top lanterns and columns with brackets not exceeding 18 m height for side entry lanterns.
This Part does not attempt to restrict the actual appearance or shape of the column or bracket. The majority of lighting columns are normally of a stepped tubular, round, octagonal or polygonal cross-section. Lighting columns may be manufactured from materials other than those listed in the foreword (e.g. wood, plastic, cast iron) or in other forms (e.g. lattice and telescopic).
This document specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under vehicle impact (passive safety) in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this document or available in separate documents.
Lichtmaste - Teil 2: Allgemeine Anforderungen und Maße
Diese Europäische Norm legt die Anforderungen an und Maße für Lichtmaste, Ausleger, Anschlussräume, Leitungswege und Schutzleiteranschlussklemmen fest. Sie gilt für gerade Maste für Aufsatzleuchten, die eine Höhe von 20 m nicht überschreiten, und für Auslegermaste mit Ansatzleuchten, die eine Höhe von 18 m nicht überschreiten.
Dieser Teil der Norm zielt nicht darauf ab, das aktuelle Erscheinungsbild oder die Form der Maste und Ausleger einzuschränken. Die Mehrzahl der Lichtmaste hat gewöhnlich einen zylindrisch abgesetzten, runden, achteckigen oder vieleckigen Querschnitt. Lichtmaste dürfen aus anderen als den im Vorwort angegebenen Werkstoffen (z. B. Holz, Kunststoff, Gusseisen) und in anderen Formen (z. B. gitterförmig und teleskopisch) hergestellt werden.
Diese Europäische Norm legt die wesentlichen Anforderungen bezüglich der Widerstandsfähigkeit gegen horizontale (Wind-)Lasten sowie die Widerstandsfähigkeit beim Anprall von Fahrzeugen (passive Sicherheit) zur Unterstützung der wesentlichen Anforderung Nr. 4 nach Nutzungssicherheit fest, die mit den entsprechenden Prüfverfahren dieser Europäischen Norm oder separater Europäischer Normen bestimmt wird.
Candélabres d'éclairage public - Partie 2: Prescriptions générales et dimensions
La présente partie spécifie les prescriptions et les dimensions des candélabres, des crosses, des compartiments électriques, des passages de câbles et des bornes de mise a terre. Elle s'applique aux candélabres a crosse d'une hauteur maximale de 18 m pour luminaires droits et aux candélabres a crosse d'une hauteur maximale de 18 m pour luminaires a entrée latérale. La présente partie ne prétend pas imposer de restrictions concernant l'aspect ou la forme du candélabre ou de la crosse.
Drogovi za razsvetljavo – 2. del: Splošne zahteve in mere
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Drogovi za razsvetljavo – 2. del: Splošne zahteve in mereLichtmaste - Teil 2: Allgemeine Anforderungen und MaßeCandélabres d'éclairage public - Partie 2: Prescriptions générales et dimensionsLighting columns - Part 2: General requirements and dimensions93.080.40Street lighting and related equipmentICS:Ta slovenski standard je istoveten z:EN 40-2:2004SIST EN 40-2:2005en01-februar-2005SIST EN 40-2:2005SLOVENSKI
STANDARD
SIST EN 40-2:2005
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 40-2October 2004ICS 93.080.40Supersedes EN 40-2:1976
English versionLighting columns - Part 2: General requirements and dimensionsCandélabres d'éclairage public - Partie 2: Prescriptionsgénérales et dimensionsLichtmaste - Teil 2: Allgemeine Anforderungen und MaßeThis European Standard was approved by CEN on 16 August 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 40-2:2004: ESIST EN 40-2:2005
EN 40-2:2004 (E) 2 Contents page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Main dimensions.5 4.1 Post top columns.5 4.2 Columns with brackets.5 4.3 Door openings and cable entry slots.8 4.3.1 Door openings.8 4.3.2 Cable entry slots.8 4.4 Base compartments and cableways.10 4.4.1 Compartment dimensions.10 4.4.2 Compartment door.10 4.4.3 Attachment of electrical equipment.10 4.4.4 Electrical cableways.10 4.4.5 Protection category.10 4.4.6 Earthing terminals.13 4.5 Column planting depth and base plate.13 4.5.1 Planting depth.13 4.5.2 Base plate.13 4.6 Flange plates.15 4.7 Connection dimensions for lanterns.16 4.7.1 General.16 4.7.2 Post top lanterns.17 4.7.3 Side entry lanterns.18 5 Tolerances.19 5.1 Straightness.19 5.2 Total length of post top columns.20 5.3 Total length of columns with brackets.20 5.4 Bracket projection.21 5.5 Lantern fixing angle.21 5.6 Door opening and cable entry slot.21 5.7 Column cross-section.21 5.7.1 Metal columns.21 5.7.2 Concrete columns.21 5.8 Connection dimensions for lantern fixing.21 5.9 Twist in columns.22 5.9.1 Columns with roots.22 5.9.2 Columns with flange plates.22 5.10 Thickness tolerance.22 5.11 Verticality tolerance.22 Annex A (informative)
Passive safety.23 Bibliography.24
SIST EN 40-2:2005
EN 40-2:2004 (E) 3 Foreword This document (EN 40-2:2004) has been prepared by Technical Committee CEN/TC 50 “Lighting columns and spigots”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by April 2005. This document supersedes EN 40-2:1976. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. This Part gives the necessary requirements for specifiers and manufacturers of columns. The majority of lighting columns are made from steel, aluminium or concrete and are normally of a stepped tubular, round, octagonal or polygonal cross-section. They are usually of neutral design with a lantern spigot either at the post top or at the end of a bracket and are produced to certain standard dimensions and tolerances. This Part of EN 40 is the second in a series relating to specifications for lighting columns. When complete, EN 40 will consist of the following Parts: Part 1: Definitions and terms Part 2: Dimensions and tolerances Part 3: Design and verification 3-1 Specification for characteristic loads 3-2 Verification by testing 3-3 Verification by calculation Part 5: Requirements for steel lighting columns Part 6: Requirements for aluminium lighting columns Part 7: Requirements for fibre reinforced polymer composite lighting columns According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
SIST EN 40-2:2005
EN 40-2:2004 (E) 4 1 Scope This document specifies the requirements and dimensions for lighting columns, brackets, base compartments, cableways and earthing terminals. It applies to post top columns not exceeding 20 m height for post top lanterns and columns with brackets not exceeding 18 m height for side entry lanterns. This Part does not attempt to restrict the actual appearance or shape of the column or bracket. The majority of lighting columns are normally of a stepped tubular, round, octagonal or polygonal cross-section. Lighting columns may be manufactured from materials other than those listed in the foreword (e.g. wood, plastic, cast iron) or in other forms (e.g. lattice and telescopic). This document specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under vehicle impact (passive safety) in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this document or available in separate documents. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 40-1:1991, Lighting columns — Part 1: Definitions and terms EN 755-8:1998, Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 8: Porthole tubes, tolerances on dimensions and form EN 10051, Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels — Tolerances on dimensions and shape EN 10210-2:1997, Hot finished structural hollow sections of non-alloy and fine grain structural steels — Part 2: Tolerances, dimensions and sectional properties EN 10219-2:1997, Cold formed welded structural hollow sections of non-alloy and fine grain steels — Part 2: Tolerances, dimensions and sectional properties EN 12767, Passive safety of support structures for road equipment — Requirements and test methods EN 50102, Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code) EN 60529, Degrees of protection provided by enclosures (IP code) (IEC 60529:1989) EN ISO 7091, Plain washers — Normal series — Product grade C (ISO 7091:2000) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 40-1:1991 apply. SIST EN 40-2:2005
EN 40-2:2004 (E) 5 4 Main dimensions 4.1 Post top columns The nominal height (h in m) shall be the height from ground level to the spigot as shown in Figure 1. Values of h should be selected from Table 1.
Table 1 — Nominal height for post top columns
h in m 3 4 5 6 7 8 9 10 12 14 15 16 18 20 h
Figure 1 — Nominal height (the shape of the column is not specified in this document)
4.2 Columns with brackets 4.2.1 The nominal height (h in m) shall be the height from ground level at the column to the height of the point of entry to the lantern as shown in Figure 2. SIST EN 40-2:2005
EN 40-2:2004 (E) 6 Values of h should be selected from Table 2. 4.2.2 The bracket projection (w in m) shall be the horizontal dimension from the column axis to the point of entry to the lantern as shown in Figure 2. Values for w should be selected from Table 3. NOTE It is rec
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.