oSIST prEN IEC 63086-1:2026

• Status: Not Published
• Public Enquiry End Date: 10-Sep-2026
• ICS: 23.120 - Ventilators. Fans. Air-conditioners
• ICS: 97.030 - Domestic electrical appliances in general
• Technical Committee: FGA - Consumer information related to household electrical appliances
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 30-Jun-2026
• Due Date: 17-Nov-2026
• Ref Project: prEN IEC 63086-1:2026 - Household and similar electrical air cleaning appliances - Methods for measuring the performance - Part 1: General requirements

• Revises: SIST EN IEC 63086-1:2020 - Household and similar electrical air cleaning appliances - Methods for measuring the performance - Part 1: General requirements
• Effective Date: 06-Aug-2024
• Revises: SIST EN IEC 63086-1:2020/A1:2023 - Amendment 1 - Household and similar electrical air cleaning appliances - Methods for measuring the performance - Part 1: General requirements (IEC 63086-1:2020/AMD1:2023)
• Effective Date: 06-Aug-2024

Overview

oSIST prEN IEC 63086-1:2026 outlines the general requirements and standardized methods for measuring the performance of household and similar electrical air cleaning appliances. Developed by SIST and in collaboration with the International Electrotechnical Commission (IEC), this standard is applicable to air cleaners intended for domestic and similar environments, covering manual, automatic, and combination appliances powered by AC or DC. The standard defines critical terms, classifications, general conditions for measurement, and procedures for evaluating performance, energy efficiency, and noise. Its implementation ensures consistency, reliability, and comparability of performance data for air purification products.

Key Topics

• Scope and Applicability: Defines the range of air cleaning appliances covered, including those powered up to 250 V (single-phase AC), 480 V (three-phase AC), and 48 V (DC). Excludes industrial, medical, and cooking fume extractor devices.
• Terminology: Provides standardized terms like air cleaner, robotic air cleaner, fresh-air air cleaner, CADR (Clean Air Delivery Rate), and device under test (DUT) to ensure uniform understanding across manufacturers and laboratories.
• Classification: Describes technologies used (mechanical filtration, electrostatic, adsorption, catalysis, UV-C, plasma, ozone, hydroxyl generation) and areas of placement (floor, table, wall, ceiling, direct plug-in, vehicle).
• Measurement Methods: Details the construction of test chambers, placement of devices, test conditions (temperature, humidity), and requirements for instrumentation (thermometer, hygrometer, power meters, CO2 detector).
• Performance Evaluation: Specifies protocols for measuring pollutant reduction efficiency, air exchange rates, energy consumption, and noise levels using tracer gas decay, CADR, and maximum performance operation mode.
• Repeatability and Accuracy: Recommends repeated testing and the use of multiple samples to increase statistical confidence and reproducibility of performance results.

Applications

oSIST prEN IEC 63086-1:2026 serves as a foundational reference for:

• Product Development: Manufacturers rely on this standard to design and validate new air cleaning appliances, ensuring compliance with international performance criteria.
• Testing Laboratories: Accredited labs use its methods to measure and certify appliance efficiency, clean air delivery rate (CADR), and other critical parameters.
• Market Surveillance: Regulatory bodies, certification agencies, and consumer organizations use the standard to assess and compare product claims regarding indoor air quality improvement.
• Consumer Confidence: Clear, harmonized measurement procedures enable end-users to make informed choices by comparing standardized product data.
• Industry Benchmarking: The standard facilitates fair competition by ensuring that all air cleaning appliances are evaluated under the same rigorous test conditions and methodologies.

Related Standards

• IEC 62301: Household electrical appliances - Measurement of standby power
  Defines methods to measure the standby power consumption of household appliances.
• IEC 60704-2-19: Household and similar electrical appliances - Test code for airborne acoustical noise - Part 2-19: Particular requirements for air cleaners
  Establishes procedures for measuring sound levels produced by air cleaning devices.
• Other IEC 63086 Parts: The series includes future parts detailing specific performance tests for different pollutants and air cleaner types.
• ISO/IEC Terminology Databases: For definitions and concept alignment, refer to IEC Electropedia and ISO Online Browsing Platform.

---

Implementing oSIST prEN IEC 63086-1:2026 helps standardize the evaluation of electric air cleaning appliances, promoting transparency, safety, and product quality in the growing market for indoor air purification solutions. Consistency in performance metrics-such as CADR and energy efficiency-benefits manufacturers, regulators, and consumers alike. For detailed guidance, testing professionals and quality assurance engineers should consult the complete standard and the additional technical references.

SLOVENSKI STANDARD
01-september-2026
Gospodinjski in podobni električni aparati za čiščenje zraka - Metode za merjenje
učinkovitost delovanja - 1. del: Splošne zahteve
Household and similar electrical air cleaning appliances - Methods for measuring the
performance - Part 1: General requirements
Elektrische Luftreiniger für den Hausgebrauch und ähnliche Zwecke – Messung der
Gebrauchseigenschaften - Teil 1: Allgemeine Anforderungen
Appareils d'épuration d'air électriques domestiques et appareils similaires - Méthodes de
mesure de l’aptitude à la fonction - Partie 1: Exigences générales
Ta slovenski standard je istoveten z: prEN IEC 63086-1:2026
ICS:
23.120 Zračniki. Vetrniki. Klimatske Ventilators. Fans. Air-
naprave conditioners
97.030 Električni aparati za dom na Domestic electrical
splošno appliances in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

59N/97/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 63086-1 ED2
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2026-06-19 2026-09-11
SUPERSEDES DOCUMENTS:
59N/77/CD, 59N/96/CC
IEC SC 59N : ELECTRICAL AIR CLEANERS FOR HOUSEHOLD AND SIMILAR PURPOSES
SECRETARIAT: SECRETARY:
United States of America Mr Wayne Morris
OF INTEREST TO THE FOLLOWING COMMITTEES: HORIZONTAL FUNCTION(S):
TC 34
ASPECTS CONCERNED:
Energy Efficiency,Environment
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft for
Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which
they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some Countries”
clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is the final stage for
submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).

TITLE:
Household and similar electrical air cleaning appliances - Methods for measuring the performance -
Part 1: General requirements
PROPOSED STABILITY DATE: 2031
NOTE FROM TC/SC OFFICERS:
The 2nd Edition of 63086-1 was prepared by the Joint Maintenance Team 6 of IEC TC59, SC59N. This document
was prepared with the assistance of many members from ISO TC142 and should be a dual -logo standard. While
this document was submitted at each stage to ISO TC 146, there has been no contact from ISO TC 146 and no
input. All comments from ISO TC142 were reviewed and resolved, which also included individually inviting
members of ISO TC 142 to attend the meetings in which we reviewed the ISO comments.

electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.

You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.

Link to Committee Draft for Vote (CDV) online document:
Click here
How to access
This link leads you to the Online Standards Development (OSD) platform for National Mirror Committee’s
(NMC) comments. The project draft may be found further down this document.

Resource materials
We recommend NCs to review the available materials to better understand the member commenting on the
OSD platform. This includes the:
• OSD NC roles overview
• How to add and submit comments to the IEC

Contact
Should you require any assistance, please contact the IEC IT Helpdesk.
*Public commenting may consult the draft content outside of OSD. The public comments can be
provided via the IEC website, or via the National Committee’s internal system.

IEC CDV 63086-1 © IEC 2026
CONTENTS
Contact . 2
CONTENTS . 1
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviated terms . 5
3.1 Terms and definitions. 5
3.2 Abbreviated terms . 7
4 Classification . 7
4.1 Types of technologies used in air cleaners . 7
4.2 Areas of placement for air cleaners . 7
5 Conditions, instrumentation, and equipment for measurements . 8
5.1 Measurements and calculations . 8
5.2 General conditions . 8
5.2.1 Test chamber conditions . 8
5.2.2 DUT conditions . 8
5.3 Test voltage and frequency . 8
5.3.1 AC-powered DUT. 8
5.3.2 DC-powered DUT . 8
5.4 Sample plan . 8
5.5 Test instrumentation . 9
5.5.1 General . 9
5.5.2 Thermometer . 9
5.5.3 Hygrometer . 9
5.5.4 Timer . 9
5.5.5 Power supply . 9
5.5.6 CO detector . 9
5.6 Test chambers . 9
5.6.1 General . 9
5.6.2 Structure of the test chambers . 9
5.6.3 Schematic of the test chambers . 11
5.7 Placement of the DUT . 13
5.7.1 General placement of the DUT. 13
5.7.2 Placement of a floor type air cleaner . 13
5.7.3 Placement of a table type air cleaner . 13
5.7.4 Placement of a wall type air cleaner . 13
5.7.5 Placement of a robotic air cleaner . 13
5.7.6 Placement of a direct plug-in type air cleaner . 13
5.7.7 Placement of an air cleaner not specified . 13
6 Determination of the air exchange rate of the test chamber . 13
6.1 Tracer gas . 13
6.2 Setting the sampling point . 13
6.3 Test chamber conditioning . 13
6.4 Tracer gas introduction . 14
6.5 Initial concentration . 14
IEC CDV 63086-1 © IEC 2026
6.6 Data sampling . 14
6.7 Decay of tracer gas . 14
6.8 Calculation of the decay constant . 14
7 Measurement of noise . 15
8 Energy efficiency . 15
8.1 Energy efficiency in maximum performance operation mode . 15
8.2 Standby power . 15
Annex A (informative) Determination of the test chamber mixing level . 16
A.1 General . 16
A.2 Setting of the external flow . 16
A.3 Injection of CO . 16
A.4 Monitoring of the CO concentration . 16
A.5 Calculation of the mixing level . 16
Annex B (normative) Standardization of calculations . 18
B.1 Test pollutant concentration . 18
B.2 Slope of decay line . 18
B.3 CADR . 18
B.3.1 Tabulation and calculation . 18
B.3.2 Certification, verification or other formal reporting. 18
Annex C (normative) Test stand for wall and direct plug-in type air cleaners . 19
Bibliography . 20

Figure 1 – Schematic of the test chambers . 13
Figure C.1 – Construction requirements for test stand for wall and direct plug-in type
air cleaners . 19

Table 1 – Test chambers . 10

IEC CDV 63086-1 © IEC 2026
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
Household and similar electrical air cleaning appliances - Methods for
measuring the performance -
Part 1: General requirements
FOREWORD
a) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical
Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt
with may participate in this preparatory work. International, governmental and non-governmental organizations
liaising with the IEC also participate in this preparation. IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
b) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
c) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
d) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
e) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
f) All users should ensure that they have the latest edition of this publication.
g) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
h) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
i) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC [had/had not] received notice of (a) patent(s),
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the pat ent database available at
https://patents.iec.ch. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 63086-1 has been prepared by subcommittee 59N: Electrical air cleaners for household
and similar purposes, of IEC technical committee 59: Performance of household and similar
electrical appliances, in co-operation with ISO technical committees 142: Cleaning equipment
for air and other gases and 146, subcommittee 6: Indoor air.
It is published as a double logo International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
59N/XX/FDIS 59N/XX/RVD
IEC CDV 63086-1 © IEC 2026
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
In this standard, the following print types are used:
– terms defined in Clause 3: bold type.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts in the IEC 63086 series, published under the general title Household and
similar electrical air cleaning appliances - Methods for measuring the performance, can be
found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
– reconfirmed,
– withdrawn, or
– revised.
IEC CDV 63086-1 © IEC 2026
1 Scope
This part of IEC 63086 applies to electrically powered household and similar air cleaners having
a rated input voltage
– up to and including 250 V for single-phase AC circuits;
– up to and including 480 V line-to-line for three-phase AC circuits;
– up to and including 48 V for DC circuits.
For combination products, this document is to be used to measure the performance of the
appliance at reducing the test pollutants .
This document is not applicable to:
– appliances intended exclusively for industrial purposes;
– appliances intended for use in medical treatment locations, such as surgical suites,
laboratories, medical treatment rooms;
– cooking fume extractors (see IEC 61591 [1]).
NOTE 1 See Clause 4 for examples of different technologies and placements of household and similar air cleaners.
NOTE 2 Battery-operated appliances are within the scope of this document. Dual-supply appliances, either mains-
supplied or battery-operated, are regarded as battery-operated appliances when operated in the battery mode.
NOTE 3 A cooking fume extractor and an air cleaner differ significantly in their main use. A cooking fume extractor
is designed to capture fumes close to the cooking surface in a kitchen environment. In the case of the cooking fume
extractor, the focus is on the direct capture of the cooking fumes (first yield capture rate), whereas in the case of air
cleaners, the focus is on general household air pollutant reduction.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 62301, Household electrical appliances - Measurement of standby power
IEC 60704-2-19, Household and similar electrical appliances - Test code for the determination
of airborne acoustical noise - Part 2-19: Particular requirements for air cleaners
3 Terms, definitions and abbreviated terms
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following
addresses:
– IEC Electropedia: available at https://www.electropedia.org/
– ISO Online browsing platform: available at https://www.iso.org/obp
3.1 Terms and definitions
3.1.1
air cleaner
electrically powered household, or similar, appliance that employs one or multiple technologies
to reduce one or more types of indoor air pollutants
IEC CDV 63086-1 © IEC 2026
3.1.2
robotic air cleaner
air cleaner (3.1.1) that operates and changes its physical location autonomously without user
intervention
Note 1 to entry: The robotic air cleaner (3.1.2) can consist of a part that houses the air cleaning function and can
have a docking station and/or other accessories to assist its operation.
3.1.3
fresh-air air cleaner
air cleaner (3.1.1) connected to the external environment, which provides pollutant-reduced
outdoor air into an indoor space
Note 1 to entry: The fresh-air air cleaner (3.1.3) can also include other auxiliary functions, such as heat exchange.
Note 2 to entry: The term "fresh" indicates in this context that the supplied outdoor air typically has a lower CO
content than the air in an occupied room. However, this does not imply that the supplied air is
...