SIST EN ISO 24034:2006
(Main)Welding consumables - Solid wires and rods for fusion welding of titanium and titanium alloys - Classification (ISO 24034:2005)
Welding consumables - Solid wires and rods for fusion welding of titanium and titanium alloys - Classification (ISO 24034:2005)
This International Standard specifies requirements for the classification of solid wires and rods for fusion welding of titanium and titanium alloys. The classification of the solid wires and rods is based on their chemical composition. For titanium-welding consumables, the compositions of the wire electrodes for the MIG process (metal inert gas welding) are the same as for the TIG process (tungsten inert-gas arc welding), the plasma arc process, the laser beam process, and other fusion welding processes. Therefore, the use of the word "wires/rods" in this classification refers to both "wire electrodes" and "wires and rods" in this International Standard.
Schweißzusätze - Massivdrähte und -stäbe zum Schmelzschweißen von Titan und Titanlegierungen - Einteilung (ISO 24034:2005)
Diese Norm legt Anforderungen für die Einteilung von Massivdrähten und Massivstäben zum Schmelz-
schweißen von Titan und Titanlegierungen fest. Die Einteilung der Massivdrähte und Massivstäbe erfolgt nach ihrer chemischen Zusammensetzung.
Bei Titan-Schweißzusätzen weist die Massivdrahtelektrode für den MIG-Prozess (Metall-Schutzgasschweißen) dieselbe Zusammensetzung auf wie für den WIG-Prozess (Wolfram-Inertgasschweißen), für den Plasma-Schweißprozess, für den Laserstrahlprozess und für andere Schmelzschweißprozesse. Daher gilt in dieser Einteilungsnorm die Bezeichnung Massivdrähte/Massivstäbe sowohl für Massivdrahtelektroden als auch für Massivdrähte und Massivstäbe.
ANMERKUNG In dieser Norm wird der Begriff Titan für Titan und Titan-Legierungen verwendet.
Die Einteilung der Titan-Massivdrähte und Massivstäbe erfolgt nach ihrer chemischen Zusammensetzung.
Produits consommables pour le soudage - Fils pleins et baguettes pleines pour le soudage par fusion du titane et des alliages de titane - Classification (ISO 24034:2005)
Dodajni materiali za varjenje – Masivne žice in palice za talilno varjenje titana in titanovih zlitin – Razvrstitev (ISO 24034:2005)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 24034:2006
01-marec-2006
Dodajni materiali za varjenje – Masivne žice in palice za talilno varjenje titana in
titanovih zlitin – Razvrstitev (ISO 24034:2005)
Welding consumables - Solid wires and rods for fusion welding of titanium and titanium
alloys - Classification (ISO 24034:2005)
Schweißzusätze - Massivdrähte und -stäbe zum Schmelzschweißen von Titan und
Titanlegierungen - Einteilung (ISO 24034:2005)
Produits consommables pour le soudage - Fils pleins et baguettes pleines pour le
soudage par fusion du titane et des alliages de titane - Classification (ISO 24034:2005)
Ta slovenski standard je istoveten z: EN ISO 24034:2005
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
SIST EN ISO 24034:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 24034:2006
---------------------- Page: 2 ----------------------
SIST EN ISO 24034:2006
EUROPEAN STANDARD
EN ISO 24034
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2005
ICS 25.160.20
English Version
Welding consumables - Solid wires and rods for fusion welding
of titanium and titanium alloys - Classification (ISO 24034:2005)
Produits consommables pour le soudage - Fils pleins et Schweißzusätze - Massivdrähte und -stäbe zum
baguettes pleines pour le soudage par fusion du titane et Schmelzschweißen von Titan und Titanlegierungen -
des alliages de titane - Classification (ISO 24034:2005) Einteilung (ISO 24034:2005)
This European Standard was approved by CEN on 4 September 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24034:2005: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 24034:2006
EN ISO 24034:2005 (E)
Foreword
This document (EN ISO 24034:2005) has been prepared by Technical Committee ISO/TC 44
"Welding and allied processes" in collaboration with Technical Committee CEN/TC 121
"Welding", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by April 2006, and conflicting national
standards shall be withdrawn at the latest by April 2006.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 24034:2005 has been approved by CEN as EN ISO 24034:2005 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 24034:2006
INTERNATIONAL ISO
STANDARD 24034
First edition
2005-10-01
Welding consumables — Solid wires and
rods for fusion welding of titanium and
titanium alloys — Classification
Produits consommables pour le soudage — Fils pleins et baguettes
pleines pour le soudage par fusion du titane et des alliages de titane —
Classification
Reference number
ISO 24034:2005(E)
©
ISO 2005
---------------------- Page: 5 ----------------------
SIST EN ISO 24034:2006
ISO 24034:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2005 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 24034:2006
ISO 24034:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Classification. 1
4 Symbols and requirements. 1
5 Mechanical properties. 2
6 Chemical analysis. 2
7 Retest. 2
8 Technical delivery conditions . 2
9 Designation. 6
Annex A (informative) Explanation of classification symbols for chemical composition. 7
© ISO 2005 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 24034:2006
ISO 24034:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 24034 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 3, Welding consumables.
iv © ISO 2005 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 24034:2006
ISO 24034:2005(E)
Introduction
This International Standard proposes a classification in order to designate wire electrodes, wires and rods in
terms of their chemical composition.
For titanium-welding consumables, there is no unique relationship between the product form (wire electrodes,
wires or rods) and the welding process used (gas-shielded metal arc welding, gas tungsten arc welding,
plasma arc welding or laser welding). For this reason, wire electrodes, wires and rods may be classified in
terms of their chemical composition.
In this International Standard, the symbol of the welding process is not used, because
a) different joining processes are performed with the same chemical component consumable, and
b) the producer is not able to determine the process symbol before shipping.
Also, it should be noted that the mechanical properties of all-weld metal test specimens or welded joints
produced by welding consumables will vary from those obtained in production joints because of differences in
welding procedure and the base-metal alloy. For this reason, the mechanical properties of all-weld metal or
welded joints for titanium-welding consumables are not specified in this classification.
Requests for an official interpretation of technical aspects of this International Standard should be directed to
the secretariat of ISO/TC 44/SC 3 via the user's member body in the user's country; a listing of these bodies
can be found at www.iso.org.
© ISO 2005 – All rights reserved v
---------------------- Page: 9 ----------------------
SIST EN ISO 24034:2006
---------------------- Page: 10 ----------------------
SIST EN ISO 24034:2006
INTERNATIONAL STANDARD ISO 24034:2005(E)
Welding consumables — Solid wires and rods for fusion
welding of titanium and titanium alloys — Classification
1 Scope
This International Standard specifies requirements for the classification of solid wires and rods for fusion
welding of titanium and titanium alloys. The classification of the solid wires and rods is based on their
chemical composition.
For titanium-welding consumables, the compositions of the wire electrodes for the MIG process (metal inert
gas welding) are the same as for the TIG process (tungsten inert-gas arc welding), the plasma arc process,
the laser beam process, and other fusion welding processes. Therefore, the use of the word “wires/rods” in
this classification refers to both “wire electrodes” and “wires and rods” in this International Standard.
NOTE In this International Standard, the word “titanium” is used for “titanium and titanium alloys”.
The classification of titanium wires/rods is based upon the chemical composition of the wires/rods.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 31-0:1992, Quantities and units — Part 0: General principles
ISO 544, Welding consumables — Technical delivery conditions for welding filler materials — Type of product,
dimensions, tolerances and markings
ISO 14344, Welding and allied processes — Flux and gas shielded electrical welding processes —
Procurement guidelines for consumables
3 Classification
The classification is divided into two
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.