SIST EN 1504-8:2005
(Main)Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 8: Quality control and evaluation of conformity
Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 8: Quality control and evaluation of conformity
This Part of this European Standard specifies procedures for quality control and evaluation of conformity, including marking and labelling of products and systems for the protection and repair of concrete according to EN 1504, Parts 2 to 7.
Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität - Teil 8: Qualitätsüberwachung und Beurteilung der Konformität
Der vorliegende Teil dieser Europäischen Norm legt Verfahren für die Qualitätsüberwachung und die Beurtei-
lung der Konformität sowie für die Kennzeichnung und Beschriftung von Produkten und Systemen für den
Schutz und die Instandsetzung von Beton entsprechend den Teilen 2 bis 7 von EN 1504 fest.
Produits et systemes pour la protection et la réparation des structures en béton - Définitions, Prescriptions, maîtrise de la qualité et évaluation de la conformité - Partie 8: Maîtrise de la qualité et évaluation de la conformité
La présente Norme européenne fixe des procédures concernant la maîtrise de la qualité et l'évaluation de la conformité ainsi que le marquage et l'étiquetage des produits et des systemes utilisés pour la protection et la réparation du béton conforme aux différentes parties de l'EN 1504.
Proizvodi in sistemi za zaščito in popravilo betonskih konstrukcij – Definicije, zahteve, kontrola kakovosti in ovrednotenje skladnosti – 8. del: Kontrola kakovosti in ovrednotenje skladnosti
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1504-8:2005
01-februar-2005
3URL]YRGLLQVLVWHPL]D]DãþLWRLQSRSUDYLOREHWRQVNLKNRQVWUXNFLM±'HILQLFLMH
]DKWHYHNRQWURODNDNRYRVWLLQRYUHGQRWHQMHVNODGQRVWL±GHO .RQWURODNDNRYRVWL
LQRYUHGQRWHQMHVNODGQRVWL
Products and systems for the protection and repair of concrete structures - Definitions,
requirements, quality control and evaluation of conformity - Part 8: Quality control and
evaluation of conformity
Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken -
Definitionen, Anforderungen, Qualitätsüberwachung und Beurteilung der Konformität -
Teil 8: Qualitätsüberwachung und Beurteilung der Konformität
Produits et systemes pour la protection et la réparation des structures en béton -
Définitions, Prescriptions, maîtrise de la qualité et évaluation de la conformité - Partie 8:
Maîtrise de la qualité et évaluation de la conformité
Ta slovenski standard je istoveten z: EN 1504-8:2004
ICS:
91.080.40 Betonske konstrukcije Concrete structures
SIST EN 1504-8:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1504-8:2005
---------------------- Page: 2 ----------------------
SIST EN 1504-8:2005
EUROPEAN STANDARD
EN 1504-8
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2004
ICS 91.080.40
English version
Products and systems for the protection and repair of concrete
structures - Definitions, requirements, quality control and
evaluation of conformity - Part 8: Quality control and evaluation
of conformity
Produits et systèmes pour la protection et la réparation de Produkte und Systeme für den Schutz und die
structures en béton - Partie 8 : Définitions, Instandsetzung von Betontragwerken - Definitionen,
Prescriptions,maîtrise de la qualité et évaluation de la Anforderungen, Qualitätsüberwachung und Beurteilung der
conformité - Partie 8: Contrôle qualité et évaluation de Konformität - Teil 8: Qualitätsüberwachung und Beurteilung
conformité der Konformität
This European Standard was approved by CEN on 23 April 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1504-8:2004: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1504-8:2005
EN 1504-8:2004 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Sampling.5
5 Evaluation of conformity.6
6 Marking and labelling .7
7 Assessment, surveillance and certification of factory production control. .8
Annex A (informative) Provisions for assessment, surveillance and certification of factory
production control.9
A.1 General.9
A.2 Tasks for the inspection body.9
A.2.1 Initial assessment of the production control.9
A.2.2 Continuous surveillance of factory production control .9
A.3 Task of the certification body.10
A.3.1 Certification of factory production control .10
A.3.2 Measures in case of non-conformity .10
2
---------------------- Page: 4 ----------------------
SIST EN 1504-8:2005
EN 1504-8:2004 (E)
Foreword
This document (EN 1504-8:2004) has been prepared by Technical Committee CEN/TC 104 “Concrete and
related products”, the secretariat of which is held by DIN.
This Part of this European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2005, and conflicting national standards shall be
withdrawn at the latest by August 2006.
It has been developed by sub-committee 8 “Products and systems for the protection and repair of concrete
structures” (Secretariat AFNOR).
This Part of this European Standard specifies procedures for sampling, evaluation of conformity, marking and
labelling of products and systems for the protection and repair of concrete. This Part 8 of EN 1504 does not
supersede any other document.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Construction Products Directive
(89/106/EC).
This Part of this European Standard is one of the Parts of this Standard on products and systems for the
repair and protection of concrete structures, the other Parts are listed below:
EN 1504-1, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 1: Definitions
prEN 1504-2, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 2: Surface protection systems for concrete
prEN 1504-3, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 3: Structural and non-structural repair
EN 1504-4, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 4: Structural bonding
prEN 1504-5, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 5: Concrete injection
prEN 1504-6, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 6: Anchoring of reinforcing steel bar
prEN 1504-7, Products and systems for the protection and repair of concrete structures — Definitions —
Requirements — Quality control and evaluation of conformity — Part 7: Reinforcement corrosion protection
ENV 1504-9, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 9: General principles for the use of products
and systems
EN 1504-10, Products and systems for the protection and repair of concrete structures — Definitions —
Requirements — Quality control and evaluation of conformity — Part 10: Site application of products and
systems and quality control of the works
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 1504-8:2005
EN 1504-8:2004 (E)
1 Scope
This Part of this European Standard specifies procedures for quality control and evaluation of conformity,
including marking and labelling of products and systems for the protection and repair of concrete according to
EN 1504, Parts 2 to 7.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies
EN 1504-1, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 1: Definitions
prEN 1504-2, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 2: Surface protection systems for concrete
prEN 1504-3, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 3: Structural and non structural repair
EN 1504-4, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 4: Structural bonding
prEN 1504-5, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 5: Concrete injection
prEN 1504-6, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 6: Anchoring of reinforcing steel bar
prEN 1504-7, Products and systems for the protection and repair of concrete structures — Definitions,
requirements, quality control and evaluation of conformity — Part 7: Reinforcement corrosion prevention
EN ISO 9001, Quality management systems - Requirements (ISO 9001:2000)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1504-1 and the following apply.
3.1
batch
quantity of material made in a single operation, or in the case of continuous production for a defined quantity
(in tonnes) which shall be demonstrated by the producer to have a uniform composition and shall not exceed
one day’s production.
3.2
identification test
test carried out to verify a declared value of the composition or property of the product or system in terms of
consistency of the production.
NOTE This is to ensure that the product or system being tested corresponds to the product or system subjected to
the initial type test, within the permitted tolerances.
4
---------------------- Page: 6 ----------------------
SIST EN 1504-8:2005
EN 1504-8:2004 (E)
3.3
performance test
test carried out to verify a value for a required property of the product or system in terms of its specified
performance during application and use.
NOTE This is to ensure that the product or system conforms to its specified performance characteristics.
3.4
declared value
value declared and documented by the manufacturer for identification or performance requirements.
4 Sampling
4.1 General
Sampling shall
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.