SIST EN 4071:2009
(Main)Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated - Classification: 1100 MPa (at ambient temperature)/425 °C
Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated - Classification: 1100 MPa (at ambient temperature)/425 °C
This standard specifies the characteristics of bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated. Classification: 1 100 MPa / 425 °C
Luft- und Raumfahrt - Sechskant-Paßschrauben, kurzes Gewinde, aus Titanlegierung, Aluminium IVD beschichtet - Klasse: 1100 MPa (bei Raumtemperatur)/425 °C
Diese Norm legt Eigenschaften von Sechskantschrauben, kurzes Gewinde, aus Titanlegierung, Aluminium-
IVD-beschichtet, fest.
Klasse: 1 100 MPa1)/425 °C2)
Série aérospatiale - Vis à tête hexagonale normale, fût normal à tolérance serrée, filetage court, en alliage de titane, revêtues aluminium IVD - Classification: 1100 MPa (à température ambiante)/425 °C
Aeronavtika - Sorniki, normalna šestroba glava, ozka toleranca, kratek navoj, iz titanove zlitine, prevlečene z aluminijem IVD - Klasifikacija: 1100 MPa (pri temperaturi okolice)/425 °C
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Sechskant-Paßschrauben, kurzes Gewinde, aus Titanlegierung, Aluminium IVD beschichtet - Klasse: 1100 MPa (bei Raumtemperatur)/425 °CSérie aérospatiale - Vis à tête hexagonale normale,
fût normal à tolérance serrée, filetage court, en alliage de titane, revêtues aluminium IVD - Classification: 1100 MPa (à température ambiante)/425 °CAerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated - Classification: 1100 MPa (at ambient temperature)/425 °C49.030.20Sorniki, vijaki, stebelni vijakiBolts, screws, studs49.025.30TitanTitanium49.025.20AluminijAluminiumICS:Ta slovenski standard je istoveten z:EN 4071:2009SIST EN 4071:2009en,de01-oktober-2009SIST EN 4071:2009SLOVENSKI
STANDARD
SIST EN 4071:2009
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4071
July 2009 ICS 49.030.20 English Version
Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated - Classification: 1 100 MPa (at ambient temperature) / 425 °C
Série aérospatiale - Vis à tête hexagonale normale,
fût normal à tolérance serrée, filetage court, en alliage de titane, revêtues aluminium IVD - Classification: 1 100 MPa (à température ambiante) / 425 °C
Luft- und Raumfahrt - Sechskant-Paßschrauben, kurzes Gewinde, aus Titanlegierung, Aluminium IVD beschichtet - Klasse: 1 100 MPa (bei Raumtemperatur) / 425 °C This European Standard was approved by CEN on 23 April 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4071:2009: ESIST EN 4071:2009
EN 4071:2009 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Required characteristics .54Designation .85Marking .86Technical specification .87Oversized bolts .9 SIST EN 4071:2009
EN 4071:2009 (E) 3 Foreword This document (EN 4071:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2010, and conflicting national standards shall be withdrawn at the latest by January 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 4071:2009
EN 4071:2009 (E) 4 1 Scope This standard specifies the characteristics of bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated. Classification: 1 100 MPa 1) / 425 °C 2) 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited ap
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.