SIST EN 12846-1:2023
(Main)Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer - Part 1: Bituminous emulsions
Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer - Part 1: Bituminous emulsions
This document specifies a method for the determination of the efflux time at 40 °C of bituminous emulsions in seconds using an efflux viscometer. Alternative test temperature is 50 °C.
NOTE The procedure described in this document can also be followed to determine efflux time at other temperatures such as 25 °C.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
Bitumen und bitumenhaltige Bindemittel - Bestimmung der Ausflusszeit mittels Ausflussviskosimeter - Teil 1: Bitumenemulsionen
Dieses Dokument legt ein Verfahren zur Bestimmung der Ausflusszeit in Sekunden von Bitumenemulsionen bei 40 °C unter Anwendung eines Ausflussviskosimeters fest. Die alternative Prüftemperatur beträgt 50 °C.
ANMERKUNG Die in diesem Dokument beschriebene Durchführung kann ebenso zur Bestimmung der Ausflusszeit bei anderen Temperaturen, wie 25 °C, angewendet werden.
WARNUNG - Die Anwendung dieses Dokuments kann den Einsatz gefährlicher Materialien, Vorgänge und Geräte bedingen. Dieses Dokument erhebt nicht den Anspruch, dass alle mit seiner Anwendung verbundenen Sicherheitsprobleme angesprochen werden. Es liegt in der Verantwortung des Anwenders dieses Dokuments, geeignete Vorsichtsmaßnahmen für den Arbeits- und Gesundheitsschutz zu treffen und die Anwendbarkeit einschränkender Vorschriften vor der Anwendung zu bestimmen.
Bitumes et liants bitumineux - Détermination du temps d'écoulement à l'aide d'un viscosimètre à écoulement - Partie 1 : Émulsions bitumineuses
Le présent document spécifie une méthode de détermination du temps d’écoulement, en secondes, à 40 °C, des émulsions bitumineuses, à l’aide d’un viscosimètre à écoulement. Une autre température d’essai possible est 50 °C.
NOTE Le mode opératoire décrit dans ce document peut aussi être suivi pour déterminer le temps d’écoulement à d’autres températures comme, par exemple, à 25 °C.
AVERTISSEMENT - L'utilisation de ce document peut impliquer le recours à des produits, des opérations et des équipements à caractère dangereux. Le présent document n'est pas censé aborder tous les problèmes de sécurité concernés par son usage. Il est de la responsabilité de l'utilisateur de ce document d'établir des règles de sécurité et d'hygiène appropriées et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.
Bitumen in bitumenska veziva - Določanje viskoznosti z iztočnim viskozimetrom - 1. del: Bitumenske emulzije
Ta dokument določa metodo za določanje časa iztoka bitumenskih emulzij pri 40 °C v sekundah z uporabo iztočnega viskozimetra. Alternativna preskusna temperatura je 50 °C.
OPOMBA: Postopek, opisan v tem dokumentu, se lahko uporabi tudi za določanje časa iztoka pri drugih temperaturah, kot je 25 °C.
OPOZORILO: Pri uporabi tega dokumenta so lahko prisotni nevarni materiali, postopki in oprema. Ta dokument ne obravnava vseh varnostnih težav, ki se navezujejo na njegovo uporabo. Za vzpostavitev ustreznih varnostnih in zdravstvenih praks ter za določitev uporabnosti regulativnih omejitev pred uporabo je odgovoren uporabnik tega dokumenta.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12846-1:2023
01-april-2023
Nadomešča:
SIST EN 12846-1:2011
Bitumen in bitumenska veziva - Določanje viskoznosti z iztočnim viskozimetrom -
1. del: Bitumenske emulzije
Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer -
Part 1: Bituminous emulsions
Bitumen und bitumenhaltige Bindemittel - Bestimmung der Ausflusszeit mittels
Ausflussviskosimeter - Teil 1: Bitumenemulsionen
Bitumes et liants bitumineux - Détermination du temps d'écoulement à l'aide d'un
viscosimètre à écoulement - Partie 1 : Émulsions bitumineuses
Ta slovenski standard je istoveten z: EN 12846-1:2022
ICS:
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
SIST EN 12846-1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12846-1:2023
---------------------- Page: 2 ----------------------
SIST EN 12846-1:2023
EN 12846-1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2022
EUROPÄISCHE NORM
ICS 91.100.50 Supersedes EN 12846-1:2011
English Version
Bitumen and bituminous binders - Determination of efflux
time by the efflux viscometer - Part 1: Bituminous
emulsions
Bitumes et liants bitumineux - Détermination du temps Bitumen und bitumenhaltige Bindemittel -
d'écoulement à l'aide d'un viscosimètre à écoulement - Bestimmung der Ausflusszeit mittels
Partie 1 : Émulsions bitumineuses Ausflussviskosimeter - Teil 1: Bitumenemulsionen
This European Standard was approved by CEN on 21 November 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12846-1:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12846-1:2023
EN 12846-1:2022 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Reagents and materials . 6
6 Apparatus . 6
7 Sampling . 7
8 Procedure. 7
8.1 General . 7
8.2 Preparation of apparatus . 7
8.3 Measurement . 8
9 Expression of results . 9
10 Precision . 9
10.1 General . 9
10.2 Repeatability . 9
10.3 Reproducibility . 10
11 Test report . 10
Bibliography . 14
2
---------------------- Page: 4 ----------------------
SIST EN 12846-1:2023
EN 12846-1:2022 (E)
European foreword
This document (EN 12846-1:2022) has been prepared by Technical Committee CEN/TC 336 “Bituminous
binders”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2023, and conflicting national standards shall be
withdrawn at the latest by June 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12846-1:2011.
EN 12846-1:2022 includes the following significant technical changes with respect to EN 12846-1:2011:
— possibility to use a vegetal oil, requirement on density replaces requirement on viscosity (Clause 5);
— the use of Sa and Sc solutions has been abandoned;
— Figures 1 and 2 have been modified to be in line with the evolution of test equipment (6.1 and 6.2);
— possibility to use alternative working apparatus that meet the requirements of this document, such
as for example an integrated block viscometer (6.1);
— mercury stem thermometers are no longer specified as reference thermometers (6.4) and Annex A
has been removed;
— emulsion samples, viscometer cups, valves and lids are preconditioned at test temperature to
minimize time of presence of the emulsion sample in the viscometer cup (8.3.3 and 8.3.4);
— more accurate description of measurement procedure (8.3);
— introduction in 8.3.9 of the possible use of a balance (alternative method) instead of a receiver
(reference method);
— precision data have been re-evaluated based on more comprehensive operational experience
(Clause 10).
The EN 12846 series consists of the following parts under the general title Bitumen and bituminous
binders — Determination of efflux time by the efflux viscometer:
— Part 1: Bituminous emulsions;
— Part 2: Cut-back and fluxed bituminous binders.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
3
---------------------- Page: 5 ----------------------
SIST EN 12846-1:2023
EN 12846-1:2022 (E)
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
4
---------------------- Page: 6 ----------------------
SIST EN 12846-1:2023
EN 12846-1:2022 (E)
1 Scope
This document specifies a method for the determination of the efflux time at 40 °C of bituminous
emulsions in seconds using an efflux viscometer. Alternative test temperature is 50 °C.
NOTE The procedure described in this document can also be followed to determine efflux time at other
temperatures such as 25 °C.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This
document does not purport to address all of the safety problems associated with its use. It is the
responsibility of the user of this document to establish appropriate safety and health practices and to
determine the applicability of regulatory limitations prior to use.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 58, Bitumen and bituminous binders — Sampling bituminous binders
EN 12594, Bitumen and bituminous binders — Preparation of test samples
EN 13302, Bitumen and bituminous binders — Determination of dynamic viscosity of bituminous binder
using a rotating spindle apparatus
EN ISO 4788:2005, Laboratory glassware — Graduated measuring cylinders (ISO 4788:2005)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org
3.1
viscosity
internal resistance of a fluid to flow
3.2
efflux time
time needed for a specified volume of a material to flow through a specified orifice at a specified
temperature
Note 1 to entry: The efflux time is an indirect measure of the viscosity and is also referred to as “pseudo-
viscosity”.
5
---------------------- Page: 7 ----------------------
SIST EN 12846-1:2023
EN 12846-1:2022 (E)
4 Principle
The efflux time of a bituminous emulsion is determined using an efflux viscometer known as the Standard
Tar Viscometer (STV), which determines the time of efflux of a 50 ml sample through a 10 mm or a 4 mm
or a 2 mm orifice at a specified temperature.
Whatever temperatures or orifice diameters used, the efflux time shall not exceed 600 s. For highly
viscous emulsions, EN 13302 shall be used.
5 Reagents and materials
3
Light mineral or vegetal oil having a density lower or equal to 930 kg/m at 15 °C.
6 Apparatus
Usual laboratory apparatus and glassware, together with the following.
6.1 Efflux viscometer (example of assembled viscometer on Figure 1) consisting essentially of a cup
with an orifice in the centre of the base that may be closed by a ball-and-socket valve (Figure 3).
Three forms are required, differing only in the size of the orifice (10 mm, 4 mm and 2 mm). For other
dimensions of the cup and the ball valve, see Figure 3 and Table 3. The cup cylinder shall be made of brass.
The ball valve should be made of corrosion-resistant metal, with a ball on a rod, a levelling peg attached
to the rod and a hemispherical top by means of which the valve may be supported in a vertical position.
The viscometer cups can be equipped with suitable
...
SLOVENSKI STANDARD
oSIST prEN 12846-1:2021
01-oktober-2021
Bitumen in bitumenska veziva - Določanje viskoznosti z iztočnim viskozimetrom -
1. del: Bitumenske emulzije
Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer -
Part 1: Bituminous emulsions
Bitumen und bitumenhaltige Bindemittel - Bestimmung der Ausflusszeit mittels
Ausflussviskosimeter - Teil 1: Bitumenemulsionen
Bitumes et liants bitumineux - Détermination du temps d'écoulement à l'aide d'un
viscosimètre à écoulement - Partie 1 : Émulsions bitumineuses
Ta slovenski standard je istoveten z: prEN 12846-1
ICS:
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
oSIST prEN 12846-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 12846-1:2021
---------------------- Page: 2 ----------------------
oSIST prEN 12846-1:2021
DRAFT
EUROPEAN STANDARD
prEN 12846-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2021
ICS 91.100.50 Will supersede EN 12846-1:2011
English Version
Bitumen and bituminous binders - Determination of efflux
time by the efflux viscometer - Part 1: Bituminous
emulsions
Bitumes et liants bitumineux - Détermination du temps Bitumen und bitumenhaltige Bindemittel -
d'écoulement à l'aide d'un viscosimètre à écoulement - Bestimmung der Ausflusszeit mittels
Partie 1 : Émulsions bitumineuses Ausflussviskosimeter - Teil 1: Bitumenemulsionen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 336.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12846-1:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 12846-1:2021
prEN 12846-1:2021 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 5
5 Reagents and materials . 5
5.1 Light mineral or vegetal oil. . 5
6 Apparatus . 5
7 Sampling . 6
8 Procedure. 6
8.1 General . 6
8.2 Preparation of apparatus . 6
8.3 Measurement . 7
9 Expression of results . 8
10 Precision . 8
10.1 General . 8
10.2 Repeatability . 8
10.3 Reproducibility . 8
10.4 Test report . 9
Bibliography . 13
2
---------------------- Page: 4 ----------------------
oSIST prEN 12846-1:2021
prEN 12846-1:2021 (E)
European foreword
This document (prEN 12846-1:2021) has been prepared by Technical Committee CEN/TC 336
“Bituminous binders”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 12846-1:2011.
The main technical changes are:
— possibility to use a vegetal oil, requirement on density replaces requirement on viscosity (5.1);
— the use of Sa and Sc solutions has been abandoned (5.2, 5.3 and 8.3.9);
— Figures 1 and 2 have been modified to be in line with the evolution of test equipment (6.1 and 6.2);
— possibility to use alternate working apparatus that meet the requirements of this document, such as
for example an integrated block viscometer (6.1);
— mercury stem thermometers are no longer specified as reference thermometers (6.4) and Annex A
has been removed;
— emulsion samples, viscometer cups, valves and lids are preconditioned at test temperature to
minimize time of presence of the emulsion sample in the viscometer cup (8.3.3 and 8.3.4);
— more accurate description of measurement procedure (8.3);
— precision data have been re-evaluated based on more comprehensive operational experience (10).
The EN 12846 series consists of the following parts under the general title Bitumen and bituminous
binders — Determination of efflux time by the efflux viscometer:
— Part 1: Bituminous emulsions;
— Part 2: Cut-back and fluxed bituminous binders.
3
---------------------- Page: 5 ----------------------
oSIST prEN 12846-1:2021
prEN 12846-1:2021 (E)
1 Scope
This document specifies a method for the determination of the efflux time at 40 °C of bituminous
emulsions in seconds using an efflux viscometer. Alternative test temperature is 50 °C.
NOTE The procedure described in this document can also be followed to determine efflux time at other
temperatures such as 25 °C.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This
document does not purport to address all of the safety problems associated with its use. It is the
responsibility of the user of this document to establish appropriate safety and health practices and to
determine the applicability of regulatory limitations prior to use.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 58, Bitumen and bituminous binders — Sampling bituminous binders
EN 12594, Bitumen and bituminous binders — Preparation of test samples
EN 13302, Bitumen and bituminous binders — Determination of dynamic viscosity of bituminous binder
using a rotating spindle apparatus
EN ISO 4788, Laboratory glassware — Graduated measuring cylinders (ISO 4788)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at https://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
viscosity
internal resistance of a fluid to flow
3.2
efflux time
time needed for a specified volume of a material to flow through a specified orifice at a specified
temperature
Note 1 to entry: The efflux time is an indirect measure of the viscosity and is also referred to as “pseudo-
viscosity”.
4
---------------------- Page: 6 ----------------------
oSIST prEN 12846-1:2021
prEN 12846-1:2021 (E)
4 Principle
The efflux time of a bituminous emulsion is determined using an efflux viscometer known as the Standard
Tar Viscometer (STV) which determines the time of efflux of a 50 ml sample through a 10 mm or a 4 mm
or a 2 mm orifice at a specified temperature.
Whatever temperatures or orifice diameters used, the efflux time shall not exceed 600 s. For highly
viscous emulsions, EN 13302 shall be used.
5 Reagents and materials
5.1 Light mineral or vegetal oil.
3
Light mineral or vegetal oil having a density lower or equal to 900 kg/m at 15 °C.
6 Apparatus
Usual laboratory apparatus and glassware, together with the following.
6.1 Efflux viscometer (example of assembled viscometer on Figure 1) consisting essentially of a cup
with an orifice in the centre of the base which may be closed by a ball-and-socket valve (Figure 3).
Three forms are required, differing only in the size of the orifice (10 mm, 4 mm and 2 mm). For other
dimensions of the cup a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.