SIST EN 62343:2013
(Main)Dynamic modules and devices - General and guidance
Dynamic modules and devices - General and guidance
This International Standard applies to all commercially available optical dynamic modules and devices. It describes the products covered by the IEC 62343-X series, defines terminology, fundamental considerations and basic approaches. The object of this standard is to - establish uniform requirements for operation, reliability and environmental properties of DMs to be implemented in the appropriate DM standard, - provide assistance to the purchaser in the selection of consistently high-quality DM products for his particular applications, as well as in the consultation of the appropriate specific DM standard(s). This standard covers performance templates, performance standards, reliability qualification requirements, hardware and software interfaces and related testing methods. Since a dynamic module integrates an optical module/device, printed wiring board, and software/firmware, the standards developed in the series will mimic appropriate existing standards. On the other hand, since "dynamic module" is a relatively new product category, the dynamic module standards series will not be bounded by the existing practices where requirements differ. The safety standards as related to dynamic modules are mostly optical power considerations, which is covered by IEC TC 76: Optical radiation safety and laser equipment.
Dynamische Module und Bauteile - Allgemeines und Leitfaden
Dispositifs et modules dynamiques - Généralités et guide
IEC 62343:2013 s'applique à tous les dispositifs et modules dynamiques optiques disponibles dans le commerce. Elle décrit les produits couverts par la série IEC 62343-X, définit la terminologie, les considérations fondamentales et les approches de base. La présente norme a pour objets:
- d'établir des exigences uniformes pour le fonctionnement, la fiabilité et les propriétés environnementales des modules dynamiques à intégrer dans la norme appropriée sur les modules dynamiques,
- de fournir une assistance à l'acheteur dans le choix de produits à modules dynamiques de haute qualité dans le cadre de ses applications particulières, ainsi que dans la consultation des normes appropriées sur les modules dynamiques spécifiques. La présente norme couvre les modèles de performance, les normes de performance, les exigences sur la qualification de la fiabilité, les interfaces matérielles et logicielles et les méthodes d'essais associées.
Mots clés: modules dynamiques optiques disponibles
Dinamični moduli in naprave - Splošno in navodilo
Ta mednarodni standard se uporablja za vse optične dinamične module in naprave, ki so na voljo na tržišču. Opisuje izdelke, vključene v IEC 62343-X, določa terminologijo, glavne dejavnike in osnovne pristope. Cilj tega standarda je – vzpostaviti enotne zahteve za delovanje, zanesljivost in okoljske lastnosti DM-jev za uvedbo v ustreznem standardu DM, – zagotoviti pomoč kupcu pri izbiri dosledno visokokakovostnih izdelkov DM za njegove določene uporabe in pri pregledu ustreznega specifičnega standarda DM. Ta standard vključuje predloge delovanja, standarde delovanja, kvalifikacijske zahteve glede zanesljivosti, vmesnike strojne in programske opreme ter povezane preskusne metode. Ker dinamični modul vključuje optični modul/napravo, tiskano vezje ter programsko/strojno opremo, bodo standardi, razviti v tej seriji, posnemali ustrezne obstoječe standarde. Ker pa je »dinamični modul« relativno nova kategorija izdelka, obstoječe prakse ne bodo zavezujoče za skupine standardov za dinamični modul, kjer se zahteve razlikujejo. Varnostni standardi, povezani z dinamičnimi moduli, obravnavajo zlasti optično moč, kar pokriva standard IEC TC 76: Varnost pri optičnem sevanju in laserska oprema.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62343:2013
01-oktober-2013
'LQDPLþQLPRGXOLLQQDSUDYH6SORãQRLQQDYRGLOR
Dynamic modules and devices - General and guidance
Dynamische Module und Bauteile - Allgemeines und Leitfaden
Dispositifs et modules dynamiques - Généralités et guide
Ta slovenski standard je istoveten z: EN 62343:2013
ICS:
33.180.01 6LVWHPL]RSWLþQLPLYODNQLQD Fibre optic systems in
VSORãQR general
SIST EN 62343:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62343:2013
---------------------- Page: 2 ----------------------
SIST EN 62343:2013
EUROPEAN STANDARD
EN 62343
NORME EUROPÉENNE
August 2013
EUROPÄISCHE NORM
ICS 33.180.01; 33.180.99
English version
Dynamic modules -
General and guidance
(IEC 62343:2013)
Modules dynamiques - Dynamische Module -
Généralités et lignes directrices Allgemeines und Leitfaden
(CEI 62343:2013) (IEC 62343:2013)
This European Standard was approved by CENELEC on 2013-07-10. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62343:2013 E
---------------------- Page: 3 ----------------------
SIST EN 62343:2013
EN 62343:2013 - 2 -
Foreword
The text of document 86C/1055/CDV, future edition 1 of IEC 62343, prepared by SC 86C "Fibre optic
systems and active devices" of IEC TC 86 "Fibre optics" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN 62343:2013.
The following dates are fixed:
– latest date by which the document has to be implemented at (dop) 2014-04-10
national level by publication of an identical national
standard or by endorsement
– latest date by which the national standards conflicting with (dow) 2016-07-10
the document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 62343:2013 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 61290 NOTE Harmonised as EN 61290 (series).
IEC 61291 NOTE Harmonised as EN 61291 (series).
IEC 61300 NOTE Harmonised as EN 61300 (series).
IEC 61753 NOTE Harmonised as EN 61753 (series).
IEC 62342-2 NOTE Harmonised as EN 62342-2.
IEC 62343-3-1:2010 NOTE Harmonised as EN 62343-3-1:2010 (not modified).
IEC 62343-5 NOTE Harmonised as EN 62343-5 (series).
---------------------- Page: 4 ----------------------
SIST EN 62343:2013
- 3 - EN 62343:2013
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60050-731 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 731: Optical fibre communication
IEC/TR 61931 - Fibre optic - Terminology - -
IEC 62343-1 series Dynamic modules - Performance standards EN 62343-1 series
IEC 62343-3 series Dynamic modules - Performance EN 62343-3 series
specification templates
IEC Guide 107 - Electromagnetic compatibility - Guide to the - -
drafting of electromagnetic compatibility
publications
---------------------- Page: 5 ----------------------
SIST EN 62343:2013
---------------------- Page: 6 ----------------------
SIST EN 62343:2013
IEC 62343
®
Edition 1.0 2013-06
INTERNATIONAL
STANDARD
Dynamic modules – General and guidance
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
Q
ICS 33.180.01; 33.180.99 ISBN 978-2-83220-854-0
Warning! Make sure that you obtained this publication from an authorized distributor.
® Registered trademark of the International Electrotechnical Commission
---------------------- Page: 7 ----------------------
SIST EN 62343:2013
– 2 – 62343 © IEC:2013(E)
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope and object . 7
2 Normative references . 7
3 Terms and definitions . 7
3.1 General terms . 8
3.2 Dynamic module terms . 8
3.3 Dynamic channel equalizer (DCE) terms . 8
3.4 Tuneable dispersion compensator (TDC) or dynamic chromatic dispersion
compensator (DCDC) terms . 9
3.5 Dynamic gain tilt equalizer (DGTE) terms . 10
3.6 Optical channel monitor (OCM) terms . 11
4 Abbreviations . 14
5 Preparation of standards . 14
5.1 General . 14
5.2 Product definition . 15
5.3 Tests . 15
5.4 Details . 15
5.5 Requirements . 15
5.6 Sample size . 15
5.7 Sample definition . 15
5.8 Groupings/sequences . 15
5.9 Pass/fail criteria . 15
5.10 Reference product definition . 15
5.11 Performance standard test report . 15
6 Electromagnetic compatibility (EMC) requirements . 16
Bibliography . 17
---------------------- Page: 8 ----------------------
SIST EN 62343:2013
62343 © IEC:2013(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DYNAMIC MODULES –
GENERAL AND GUIDANCE
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62343 has been prepared by subcommittee 86C: Fibre optic
systems and active devices, of IEC technical committee 86: Fibre optics.
The text of this standard is based on the following documents:
CDV Report on voting
86C/1055/CDV 86C/1088/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all the parts in the IEC 62343 series, published under the general title Dynamic
modules, can be found on the IEC website.
The structure of the IEC 62343 series, under the general title Dynamic modules, is as
follows:
---------------------- Page: 9 ----------------------
SIST EN 62343:2013
– 4 – 62343 © IEC:2013(E)
• 62343-1 series Part 1: Performance standards
• 62343-2 Part 2: Reliability qualification
• 62343-3 Performance specification templates
• 62343-4 series Software and hardware interface standards
• 62343-5 series Test methods
• 62343-6 series Technical reports
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
---------------------- Page: 10 ----------------------
SIST EN 62343:2013
62343 © IEC:2013(E) – 5 –
INTRODUCTION
This International Standard applies to dynamic devices as defined in IEC/TS 62538. It
contains general guidance for the IEC 62343 series related to dynamic devices, and
definitions which apply to dynamic devices. The dynamic module, or device, has two
distinguishing characteristics: dynamic and module.
“Dynamic” highlights the functions of the products to include “tuning, varying, switching,
configuring, and other continuous optimization,” often accomplished by electronics, firmware,
software or their combinations. The dynamic device usually has a certain level of intelligence
to monitor or measure the situation and make decisions for necessary (optimization) actions.
The behaviour of dynamic modules may be characterized by transient characteristics as the
dynamic module undergoes tuning, switching, configuring and other continuous optimization.
Characterization of transient characteristics will be considered in individual dynamic module
standards.
“Module” defines that the products covered by the standard are the integration of active and
passive components (either or both), through interconnecting materials or devices. The
controlling electronics can be inside or outside the optical package (that contains all or most
of the optical components and interconnection). The product can look like a small printed
wiring board (PWB or child-board with mounted optical module) or a small box (housing) with
optical components and electronics enclosed. In the former case, it is more like an assembly
(generally not packaged in a box or housing) than a module (generally packaged in a box or
housing).
For historical reasons and convenience, a dynamic module or device is referred to as a
dynamic module in the IEC 62343-X series.
The number of dynamic modules and devices is rapidly growing as optical communications
networks evolve. The following list provides some examples of the products covered by the
IEC 62343-X series. It should be noted that the list is not exhaustive and the products to be
covered are not limited by the listed examples:
• channel gain equalizer;
• dynamic channel equalizer;
• dynamic gain tilt equalizer;
• dynamic slope equalizer;
• tuneable chromatic dispersion compensator;
• polarization mode dispersion compensator;
• reconfigurable optical add-drop multiplexer;
• switch with monitoring and controls;
• variable optical attenuator with monitoring and controls.
The IEC 62343 series will cover performance templates, performance standards, reliability
qualification requirements, hardware and software interfaces, and related testing methods.
A complete set of standards related to a dynamic module or device should include the
following:
• optical performance standards;
• reliability qualification standards;
• optical performance specification templates;
• hardware and software interface standards;
• test methods;
---------------------- Page: 11 ----------------------
SIST EN 62343:2013
– 6 – 62343 © IEC:2013(E)
• technical reports.
The safety standards related to dynamic modules are mostly optical power considerations,
which are covered by IEC TC 76: Optical radiation safety and laser equipment.
Only those dynamic modules for which standards are complete or in preparation are included
in Clause 3. To reflect the rapidly growing market for dynamic modules, additional terms and
definitions will be added in subsequent revisions as the series expands.
It should be noted that optical amplifiers could be regarded as dynamic modules. They are not
included in the IEC 62343-X series, but are covered in their own series of IEC standards.
---------------------- Page: 12 ----------------------
SIST EN 62343:2013
62343 © IEC:2013(E) – 7 –
DYNAMIC MODULES –
GENERAL AND GUIDANCE
1 Scope and object
This International Standard applies to all commercially available optical dynamic modules and
devices. It describes the products covered by the IEC 62343-X series, defines terminology,
fundamental considerations and basic approaches.
The object of this standard is to
• establish uniform requirements for operation, reliability and environmental properties of
DMs to be implemented in the appropriate DM standard,
• provide assistance to the purchaser in the selection of consistently high-quality DM
products for his particular applications, as well as in the consultation of the appropriate
specific DM standard(s).
This standard covers performance templates, performance standards, reliability qualification
requirements, hardware and software interfaces and related testing methods.
Since a dynamic module integrates an optical module/device, printed wiring board, and
software/firmware, the standards developed in the series will mimic appropriate existing
standards. On the other hand, since "dynamic module" is a relatively new product category,
the dynamic module standards series will not be bounded by the existing practices where
requirements differ.
The safety standards as related to dynamic modules are mostly optical power considerations,
which is covered by IEC TC 76: Optical radiation safety and laser equipment.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60050-731, International Electrotechnical Vocabulary – Chapter 731: Optical fibre
communication
IEC/TR 61931, Fibre optic – Terminology
IEC 62343-1 (all parts), Dynamic modules – Optical performance standards
IEC 62343-3 (all parts), Dynamic modules – Optical performance specification templates
IEC Guide 107, Electromagnetic compatibility – Guide to the drafting of electromagnetic
compatibility publications
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
---------------------- Page: 13 ----------------------
SIST EN 62343:2013
– 8 – 62343 © IEC:2013(E)
The definitions listed in this clause refer to the meaning of the terms used in the specifications
of DMs. Only th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.