SIST EN ISO 16228:2018
(Main)Fasteners - Types of inspection documents (ISO 16228:2017)
Fasteners - Types of inspection documents (ISO 16228:2017)
This International standard specifies the different types of fastener inspection documents, issued by the fastener manufacturer or distributor and/or by the external authorized representative, on specific request of the purchaser at the time of the order:
- declaration of compliance (F2.1),
- test reports (F2.2, F3.1, F3.2 and F3.3).
NOTE The term “certificate” is in common use, however for fastener inspection documents the terminology to be used is “test report”.
It specifies requirements for the content of each fastener inspection document, in conjunction with the order, the relevant standards and/or specified requirements.
This International standard applies to finished fasteners such as bolts, screws, studs, nuts, washers, pins, rivets, etc. made of steel, stainless steel, non-ferrous metal or non-metallic material.
This International Standard is not intended for special-purpose or specially engineered applications requiring other types of procedures (e.g. initial samples …).
Examples of inspection documents are given in Annex A (informative). An example of a coding system identifying the sections in fastener inspection documents is given in Annex B (informative).
Mechanische Verbindungselemente - Prüfbescheinigungen (ISO 16228:2017)
Dieses Dokument legt die verschiedenen Arten von Prüfbescheinigungen für mechanische Verbindungs-elemente fest, die vom Hersteller oder Vertreiber von mechanischen Verbindungselementen und/oder einem externen bevollmächtigten Vertreter auf konkrete Anfrage des Käufers zum Zeitpunkt der Bestellung ausgestellt werden:
- Konformitätserklärung (F2.1);
- Prüfberichte (F2.2, F3.1 und F3.2).
ANMERKUNG Allgemein wird der Begriff "Zertifikat" verwendet, jedoch ist für Prüfbescheinigungen für mechanische Verbindungselemente der Begriff "Prüfberichte" zu verwenden.
Dieses Dokument legt die Anforderungen an den Inhalt jeder Prüfbescheinigung für mechanische Verbin-dungselemente fest, in Verbindung mit der Bestellung, den zugehörigen Normen und den festgelegten Anfor¬derungen.
Dieses Dokument wird auf fertig hergestellte mechanische Verbindungselemente angewendet, wie Schrauben, Muttern, Unterlegscheiben, Stifte, Niete usw., hergestellt aus Stahl, nichtrostendem Stahl, Nichteisenmetallen oder nichtmetallischen Werkstoffen.
Dieses Dokument gilt nicht für Sonderzwecke oder speziell entwickelte Anwendungen, die andere Arten von Verfahren (z. B. Erstmuster) erfordern.
Beispiele für Prüfbescheinigungen sind im Anhang A gegeben. Ein Beispiel eines Kennnummernsystems zum Identifizieren der Abschnitte in Prüfbescheinigungen für mechanische Verbindungselemente ist im Anhang B gegeben.
Fixations - Documents de contrôle (ISO 16228:2017)
ISO 16228:2017 spécifie les différents types de documents de contrôle pour les fixations fournis par le fabricant ou le distributeur des fixations, ou par le représentant externe autorisé, à la demande spécifique du client lors de la commande:
- déclaration de conformité (F2.1);
- rapports d'essai (F2.2, F3.1 et F3.2).
NOTE Le terme «certificat» est couramment employé, cependant pour les documents de contrôle des fixations la terminologie à utiliser est «rapport d'essai».
ISO 16228:2017 spécifie les exigences relatives au contenu de chaque document de contrôle des fixations, en fonction de la commande, des normes appropriées qui s'appliquent et/ou des exigences spécifiées.
ISO 16228:2017 s'applique aux fixations finies, tels que les vis, goujons, tiges filetées, écrous, rondelles, goupilles, rivets, etc. en acier, en acier inoxydable, en métaux non ferreux ou en matériaux non métalliques.
ISO 16228:2017 n'est pas destiné aux applications nécessitant des procédures spéciales ou spécifiques, qui nécessitent d'autres types de processus (par exemple échantillons initiaux).
L'Annexe A (informative) fournit des exemples de documents de contrôle. L'Annexe B (informative) fournit un exemple de système de codification identifiant les rubriques des documents de contrôle pour les fixations.
Vezni elementi - Vrste certifikatov kontrole (ISO 16228:2017)
Ta mednarodni standard določa različne vrste certifikatov kontrole za vezne elemente, ki jih izdajo proizvajalci ali distributerji veznih elementov in/ali zunanji pooblaščeni zastopnik na izrecno zahtevo kupca ob naročilu: – izjava o skladnosti (F2.1), – poročila o preskusih (F2.2, F3.1, F3.2 in F3.3). OPOMBA: Izraz »certifikat« je v splošni rabi, vendar se v certifikatih kontrole za vezne elemente uporablja izraz »poročilo o preskusu«. Določa zahteve za vsebino vsakega certifikata kontrole za vezne elemente v povezavi z naročilom, relevantnimi standardi in/ali določenimi zahtevami. Ta mednarodni standard se uporablja za dokončane vezne elemente, kot so sorniki, vijaki, stojni vijaki, matice, podložke, zatiči, zakovice ipd. iz jekla, nerjavnega jekla, neželeznih kovin ali nekovinskih materialov. Ta mednarodni standard ni predviden za posebne namene ali načine uporabe, ki zahtevajo druge vrste postopkov (npr. začetne vzorce ipd.). Primeri teh certifikatov kontrole so podani v dodatku A (informativni). Primer sistema kodiranja za določanje razdelkov v certifikatih kontrole za vezne elemente je podan v dodatku B (informativni).
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 16228:2018
01-april-2018
Vezni elementi - Vrste certifikatov kontrole (ISO 16228:2017)
Fasteners - Types of inspection documents (ISO 16228:2017)
Mechanische Verbindungselemente - Prüfbescheinigungen (ISO 16228:2017)
Fixations - Documents de contrôle (ISO 16228:2017)
Ta slovenski standard je istoveten z: EN ISO 16228:2018
ICS:
21.060.01 Vezni elementi na splošno Fasteners in general
SIST EN ISO 16228:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 16228:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 16228:2018
EN ISO 16228
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2018
EUROPÄISCHE NORM
ICS 21.060.01
English Version
Fasteners - Types of inspection documents (ISO
16228:2017)
Fixations - Types de documents de contrôle (ISO Mechanische Verbindungselemente - Arten von
16228:2017) Prüfbescheinigungen (ISO 16228:2017)
This European Standard was approved by CEN on 3 August 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16228:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 16228:2018
EN ISO 16228:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 16228:2018
EN ISO 16228:2018 (E)
European foreword
This document (EN ISO 16228:2018) has been prepared by Technical Committee ISO/TC 2 “Fasteners”
in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by
BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2018, and conflicting national standards shall
be withdrawn at the latest by August 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16228:2017 has been approved by CEN as EN ISO 16228:2018 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 16228:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 16228:2018
INTERNATIONAL ISO
STANDARD 16228
First edition
2017-11
Fasteners — Types of inspection
documents
Fixations — Types de documents de contrôle
Reference number
ISO 16228:2017(E)
©
ISO 2017
---------------------- Page: 7 ----------------------
SIST EN ISO 16228:2018
ISO 16228:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 16228:2018
ISO 16228:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Inspection . 2
4.1 Types of inspection documents for material. 2
4.2 Types of inspection for fasteners . 3
4.2.1 Non-specific inspection for fasteners . 3
4.2.2 Specific inspection for fasteners . 3
4.3 Types of inspection documents for fasteners . 3
4.3.1 General. 3
4.3.2 Fastener declaration of compliance F2.1 . 3
4.3.3 Fastener test report F2.2. 4
4.3.4 Fastener test report F3.1. 4
4.3.5 Fastener test report F3.2. 4
5 Requirements for fastener inspection documents . 4
5.1 General . 4
5.2 Maintenance of data for inspection documents . 5
5.3 Traceability . 5
5.4 Inspection document sources . 5
5.5 Subcontracted tests and/or inspection . 6
5.6 Sampling . 6
5.7 Reporting of test/inspection results . 6
5.8 Minimum results to be included for each type of fasteners . 7
5.9 Validation of the inspection document . 9
6 Required content for each type of fastener inspection document . 9
6.1 General . 9
6.2 Content of the fastener declaration of compliance F2.1 .10
6.3 Content of the fastener test report F2.2 .10
6.4 Content of the fastener test report F3.1 .11
6.5 Content of the fastener test report F3.2 .12
7 Amendment to inspection documents .13
8 Transmission of inspection documents.13
Annex A (informative) Examples of inspection documents .14
Annex B (informative) Code numbers applicable to fasteners .18
Bibliography .26
© ISO 2017 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 16228:2018
ISO 16228:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 7, Reference
standards.
iv © ISO 2017 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 16228:2018
ISO 16228:2017(E)
Introduction
This document specifies the fastener inspection documents which can be supplied when requested at
the time of the order.
Before publication of this document, inspection documents according to ISO 10474 or EN 10204 were
also applied for fasteners. This document was developed specifically for fasteners, as a preferred
alternative to ISO 10474 or EN 10204.
Data in inspection documents may be collected from in-process control during the manufacture of the
fasteners and/or from final control on the finished fasteners based on sampling. In-process control
during manufacture within a certified quality assurance system operated by the manufacturer gives
the most reliable information about conformance of the fasteners (for more information regarding
acceptance inspection or quality assurance for fasteners, see ISO 3269 or ISO 16426).
Inspection documents for fasteners may include material, mechanical, physical, dimensional, functional
and finish-coating properties, as agreed at the time of the order.
© ISO 2017 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 16228:2018
---------------------- Page: 12 ----------------------
SIST EN ISO 16228:2018
INTERNATIONAL STANDARD ISO 16228:2017(E)
Fasteners — Types of inspection documents
1 Scope
This document specifies the different types of fastener inspection documents issued by the fastener
manufacturer or distributor and/or by the external authorized representative on specific request of the
purchaser at the time of the order.
— declaration of compliance (F2.1);
— test reports (F2.2, F3.1 and F3.2).
NOTE The term “certificate” is in common use, however for fastener inspection documents the terminology
to be used is “test report”.
This document specifies requirements for the content of each fastener inspection document, in
conjunction with the order, the relevant standards and/or specified requirements.
This document is applicable to finished fasteners such as bolts, screws, studs, nuts, washers, pins,
rivets, etc. made of steel, stainless steel, non-ferrous metal or non-metallic material.
This document does not apply to special-purpose or specially engineered applications requiring other
types of procedures (e.g. initial samples).
Examples of inspection documents are given in Annex A. An example of a coding system identifying the
sections in fastener inspection documents is given in Annex B.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws
and studs with specified property classes — Coarse thread and fine pitch thread
ISO 898-2, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with
specified property classes — Coarse thread and fine pitch thread
1)
ISO 898-3, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 3: Flat washers
with specified property classes
ISO 898-5, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 5: Set screws and
similar threaded fasteners with specified hardness classes — Coarse thread and fine pitch thread
ISO 1891-4:2017, Fasteners — Terminology — Part: 4: Control, inspection, delivery, acceptance and quality
ISO 2320, Fasteners — Prevailing torque steel nuts — Functional properties
ISO 2702, Heat-treated steel tapping screws — Mechanical properties
ISO 3269, Fasteners — Acceptance inspection
ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws
and studs
1) Under preparation.
© ISO 2017 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 16228:2018
ISO 16228:2017(E)
ISO 3506-2, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 2: Nuts
ISO 3506-3, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 3: Set screws and
similar fasteners not under tensile stress
ISO 3506-4, Mechanical properties of corrosion-resistant stainless steel fasteners — Part 4: Tapping screws
ISO 10666, Drilling screws with tapping screw thread — Mechanical and functional properties
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1891-4 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
authorized representative
person who is authorized as a quality assurance representative to validate and sign inspection
documents on behalf of the supplier or the purchaser
3.2
external authorized representative
third party agreed between the purchaser and the supplier or a purchaser's requested inspection
representative, or an inspection representative designated by an official regulation
3.3
validation
confirmation by the authorized representative (3.1) or the external authorized representative (3.2) of the
content of the inspection document and final approval by means of signature
3.4
pass-through distributor
fastener distributor who sells the original manufacturer's fasteners as received, without altering the
fasteners or the packages
[SOURCE: ISO 1891-4:2017, 3.6.4]
3.5
alteration distributor
fastener distributor who alters fasteners prior to delivery
[SOURCE: ISO 1891-4:2017, 3.6.6]
4 Inspection
4.1 Types of inspection documents for material
For material inspection documents 2.1, 2.2, 3.1 and 3.2, see ISO 10474 or other relevant technical
specifications (e.g. EN 10204).
2 © ISO 2017 – All rights reserved
---------------------- Page: 14 ----------------------
SIST EN ISO 16228:2018
ISO 16228:2017(E)
4.2 Types of inspection for fasteners
4.2.1 Non-specific inspection for fasteners
Inspection carried out in order to verify that the fasteners comply with the order and relevant standards
and/or specified requirements. The fasteners inspected and/or tested are not necessarily part of the
actually delivered fasteners provided that they
— are in accordance with the same standard or technical specification,
— are manufactured from the same material designation,
— are manufactured with the same manufacturing sequences and under same conditions,
— have the same shape, and
— have similar dimensions, where the differences do not impact the test results.
4.2.2 Specific inspection for fasteners
Inspection carried out before delivery, on the fasteners from the original manufacturing lot and in
accordance with the product specification, in order to verify that the fasteners comply with the order
and relevant standards and/or specified requirements.
4.3 Types of inspection documents for fasteners
4.3.1 General
The types of inspection document for fasteners are summarized in Table 1.
Table 1 — Inspection documents for fasteners
Type and name of
fastener inspection When Content Validation
document
F2.1 Fastener Requested by the Declaration of conformance The manufacturer or
declaration of purchaser at the time for the delivered fasteners, distributor authorized
compliance of the order without results representative
F2.2 Fastener test Requested by the Declaration of conformance The manufacturer
report purchaser at the time for the delivered fasteners, authorized representa-
of the order with results based on tive
non-specific inspection
F3.1 Fastener test Specifically requested by Declaration of conformance The manufacturer or
report the purchaser and agreed for the delivered fasteners, distributor authorized
at the time of the order with results from specific representative
inspection
F3.2 Fastener test Specifically requested by Declaration of conformance The manufacturer or
report the purchaser and agreed for the delivered fasteners, distributor authorized
at the time of the order with results from specific representative and ei-
inspection ther the purchaser
authorized representa-
tive or the external au-
thorized representative
4.3.2 Fastener declaration of compliance F2.1
Document issued by the manufacturer or distributor declaring that the delivered fasteners are in
compliance with the order and relevant standards and/or specified requirements without inclusion of
results.
© ISO 2017 – All rights reserved 3
---------------------- Page: 15 ----------------------
SIST EN ISO 16228:2018
ISO 16228:2017(E)
F2.1 inspection document shall be validated by either the manufacturer’s authorized representative or
the distributer’s authorized representative.
4.3.3 Fastener test report F2.2
Document issued by the manufacturer declaring that the delivered fasteners are in compliance with
the order and relevant standards and/or specified requirements, and in which results based on non-
specific inspection are supplied.
It is the responsibility of the manufacturer to determine the correlation between the results on the
inspection document and the delivered fasteners in order to demonstrate conformance.
Results shall be taken from raw material certificates, fastener in-process control and/or final inspection
which shall be performed by (a) suitably qualified person(s).
The resulting data shall be assessed and transferred into the inspection document by (a) suitably
qualified person(s).
F2.2 inspection document shall be validated by the manufacturer's authorized representative.
4.3.4 Fastener test report F3.1
Document issued by the manufacturer or distributor declaring that the delivered fasteners are in
compliance with the order and relevant standards and/or specified requirements and in which results
from specific inspection are supplied.
Results shall be taken from raw material certificates (3.1 or 3.2), fastener in-process control and/or
final inspection which shall be performed by (a) suitably qualified person(s).
The resulting data shall be assessed and transferred into the inspection document by (a) suitably
qualified person(s).
F3.1 inspection document shall be validated by either the manufacturer's authorized representative or
the distributor's authorized representative.
4.3.5 Fastener test report F3.2
Document issued by the manufacturer or distributor declaring that the delivered fasteners are in
compliance with the order and relevant standards and/or specified requirements, and in which results
from specific inspection are supplied.
Results shall be taken from fastener inspection which shall be performed by (a) suitably qualified
person(s). Results for raw material(s) shall be taken either from the raw material certificate(s) (3.1 or
3.2) or from the fastener inspection.
F3.2 inspection document shall be validated by both the manufacturer’s or distributor’s authorized
representative and either the purchaser’s authorized representative or the external authorized
representative.
5 Requirements for fastener inspection documents
5.1 General
Inspection document in accordance with this document is only supplied on request of the purchaser.
The type of inspection document, F2.1, F2.2, F3.1 or F3.2 shall be agreed at the time of the order.
Fasteners produced in accordance with a product standard (and/or technical specification) shall meet
all the applicable requirements, regardless of which controls are performed during manufacturing
and/or final inspection. It is the responsibility of the manufacturer and distributor to apply suitable
4 © ISO 2017 – All rights reserved
---------------------- Page: 16 ----------------------
SIST EN ISO 16228:2018
ISO 16228:2017(E)
methods of their choice, such as in-process control or final inspection, to ensure that the manufactured
lot does conform to the specified requirements.
Even when receiving an inspection document, the purchaser is responsible for the approval of
the delivered fasteners by acceptance inspection procedures in accordance with ISO 3269 unless
otherwise agreed.
The inspection documents F2.1 and F2.2 should include the fastener manufacturing lot number of the
delivered fasteners, however a trace lot number may replace or complement the manufacturing lot
number. The inspection documents F3.1 and F3.2 shall include the fastener manufacturing lot number
of the delivered fasteners.
Each inspection document is only valid for the as-delivered condition of the related fasteners referenced
in the inspection document. Any further processing after delivery (e.g. coating) altering the fasteners
may invalidate all or part of the content of the inspection document.
5.2 Maintenance of data for inspection documents
The fastener supplier issuing an inspection document shall maintain in-process control and/or final
test/inspection records either in hardcopy or electronically for a minimum period of three years.
5.3 Traceability
Fasteners shall be fully traceable by the manufacturing lot number (or trace lot number), and to
maintain lot integrity, manufacturing lots shall not be commingled.
NOTE For the definitions of manufacturing lot number, trace lot number and commingling, see ISO 1891-4.
The purchaser who receives the fastener inspection document is responsible for maintaining
subsequent traceability when required. Upon opening the original packaging, the purchaser assumes
full responsibility for all subsequent traceability.
In case of dispute, the supplier shall be able to provide all necessary documentation and test/inspection
records related to the manufacturing lot number (or trace lot number).
5.4 Inspection document sources
The fastener manufacturer is allowed to
— generate F2.1, F2.2, F3.1 or F3.2 inspection documents, and
— transfer the original data from suppliers into the manufacturer inspection document, provided that
full traceability is ensured; the test/inspection results of the original inspection document shall not
be modified.
The pass-through distributor and repackaging distributor are allowed to
— generate F2.1 or F2.2 inspection documents only by transferring data from F2.1 or F2.2 from the
manufacturer,
— generate F3.1 or F3.2 inspection documents,
— supply the incoming inspection document F2.1, F2.2, F3.1 or F.3.2 from the manufacturer, and
— transfer the original data from F3.1 of the manufacturer into the distributor F3.1 inspection
document, provided that full traceability is ensured; the test/inspection results of the original
inspection document shall not be modified.
The alteration distributor is allowed to
— generate F2.1 inspection documents only by transferring data from the manufacturer,
© ISO 2017 – All rights reserved 5
---------------------- Page: 17 ----------------------
SIST EN ISO 16228:2018
ISO 16228:2017(E)
— generate F2.2 inspection documents by transferring data from F2.2 from the manufacturer provided
that the reported properties have not been altered, by testing the altered properties and by adding
his own test results,
— generate F2.1, F3.1 or F3.2 inspection documents, and
— transfer the original data from F3.1 of the manufacturer into the distributor F3.1 inspection
document after it has been determin
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.