SIST EN ISO 8029:2011
(Main)Plastics hose - General-purpose collapsible water hose, textile-reinforced - Specification (ISO 8029:2007)
Plastics hose - General-purpose collapsible water hose, textile-reinforced - Specification (ISO 8029:2007)
This International Standard specifies the requirements for four types of textile-reinforced thermoplastics collapsible water hoses for general applications for use in the temperature range of −10 °C to 55 °C.
Such hoses are classified into four types, as follows:
⎯low pressure, designed for a maximum working pressure of up to 4,0 bar at 23 °C and up to 2,0 bar at 55 °C;
⎯medium pressure, for a maximum working pressure of up to 7,0 bar at 23 °C and up to 3,6 bar at 55 °C;
⎯high pressure, for a maximum working pressure of up to 10,0 bar at 23 °C and up to 5,1 bar at 55 °C;
⎯extra-high pressure, for a maximum working pressure of up to 15,5 bar at 23 °C and up to 7,9 bar at 55 °C.
This standard does not apply to products used for fire-fighting or the conveyance of drinking water.
Kunststoffschläuche - Faltbarer Wasserschlauch mit Textileinlage für allgemeine Anwendung - Anforderung (ISO 8029:2007)
Diese Internationale Norm legt die Anforderungen für vier Arten von textilverstärkten, thermoplastischen, faltbaren Wasserschläuchen für allgemeine Anwendungen in einem Temperaturbereich von -10 °C bis +55 °C fest.
Solche Schläuche werden wie folgt eingeordnet in vier Klassen:
- Niederdruck, ausgelegt für einen maximalen Betriebsdruck bis zu 4,0 bar bei 23 °C und bis zu 2,0 bar bei 55 °C;
- Mitteldruck, für einen maximalen Betriebsdruck bis zu 7,0 bar bei 23 °C und bis zu 3,6 bar bei 55 °C;
- Hochdruck, für einen maximalen Betriebsdruck bis zu 10,0 bar bei 23 °C und bis zu 5,1 bar bei 55 °C;
- Extra-Hochdruck, für einen maximalen Betriebsdruck bis zu 15,5 bar bei 23 °C und bis zu 7,9 bar bei 55 °C.
Diese Norm gilt nicht für Produkte zur Verwendung bei der Brandbekämpfung oder den Transport von Trinkwasser.
Tuyaux plastiques - Tuyaux d'eau écrasables d'usage général renforcés textiles - Spécifications (ISO 8029:2007)
L'ISO 8029:2007 spécifie les exigences relatives à quatre types de tuyaux d'eau thermoplastiques écrasables renforcés textiles destinés à des applications générales pour utilisation à des températures comprises entre -10 °C et +55 °C.
Ces tuyaux sont classés selon les quatre types suivants:
basse pression, conçus pour une pression maximale de service jusqu'à 4,0 bar à 23 °C et jusqu'à 2,0 bar à 55 °C;
moyenne pression, pour une pression maximale de service jusqu'à 7,0 bar à 23 °C et jusqu'à 3,6 bar à 55 °C;
haute pression, pour une pression maximale de service jusqu'à 10,0 bar à 23 °C et de 5,1 bar à 55 °C;
très haute pression, pour une pression maximale de service jusqu'à 15,5 bar à 23 °C et jusqu'à 7,9 bar à 55 °C.
L'ISO 8029:2007 ne s'applique pas aux produits utilisés pour la lutte contre les incendies ou l'adduction d'eau potable.
Polimerna cev - S tekstilom ojačena zložljiva vodna cev za splošno uporabo - Specifikacija (ISO 8029:2007)
Ta mednarodni standard določa zahteve za štiri vrste s tekstilom utrjenih plastomernih zložljivih vodnih cevi za splošno uporabo v temperaturnem razponu med −10 °C in 55 °C.
Take cevi so tako razvrščene v štiri vrste:
⎯ nizkotlačne, narejene za maksimalni delovni tlak do 4,0 bar pri 23 °C in do 2,0 bar pri 55 °C;;
⎯ srednjetlačne, za maksimalni delovni tlak do 7,0 bar pri 23 °C in do 3,6 bar pri 55 °C;
⎯ visokotlačne, za maksimalni delovni tlak do 10,0 bar pri 23 °C in do 5,1 bar pri 55 °C;
⎯ posebno visokotlačne, za maksimalni delovni tlak do 15,5 bar pri 23 °C in do 7,9 bar pri 55 °C.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8029:2011
01-maj-2011
1DGRPHãþD
SIST EN 28029:2001
3ROLPHUQDFHY6WHNVWLORPRMDþHQD]ORåOMLYDYRGQDFHY]DVSORãQRXSRUDER
6SHFLILNDFLMD ,62
Plastics hose - General-purpose collapsible water hose, textile-reinforced - Specification
(ISO 8029:2007)
Kunststoffschläuche - Faltbarer Wasserschlauch mit Textileinlage für allgemeine
Anwendung - Anforderung (ISO 8029:2007)
Tuyaux plastiques - Tuyaux d'eau écrasables d'usage général renforcés textiles -
Spécifications (ISO 8029:2007)
Ta slovenski standard je istoveten z: EN ISO 8029:2010
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN ISO 8029:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8029:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 8029:2011
EUROPEAN STANDARD
EN ISO 8029
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2010
ICS 23.040.70 Supersedes EN 28029:1993
English Version
Plastics hose - General-purpose collapsible water hose, textile-
reinforced - Specification (ISO 8029:2007)
Tuyaux plastiques - Tuyaux d'eau écrasables d'usage Kunststoffschläuche - Faltbarer Wasserschlauch mit
général renforcés textiles - Spécifications (ISO 8029:2007) Textileinlage für allgemeine Anwendung - Anforderung (ISO
8029:2007)
This European Standard was approved by CEN on 12 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8029:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8029:2011
EN ISO 8029:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8029:2011
EN ISO 8029:2010 (E)
Foreword
The text of ISO 8029:2007 has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber
products” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
8029:2010 by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at
the latest by March 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 28029:1993.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 8029:2007 has been approved by CEN as a EN ISO 8029:2010 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8029:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 8029:2011
INTERNATIONAL ISO
STANDARD 8029
Second edition
2007-06-15
Plastics hose — General-purpose
collapsible water hose, textile-
reinforced — Specification
Tuyaux plastiques — Tuyaux d'eau écrasables d'usage général
renforcés textiles — Spécifications
Reference number
ISO 8029:2007(E)
©
ISO 2007
---------------------- Page: 7 ----------------------
SIST EN ISO 8029:2011
ISO 8029:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 8029:2011
ISO 8029:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Classification. 2
5 Couplings and end fittings . 2
6 Materials and construction . 2
7 Dimensions and tolerances . 3
7.1 Inside diameter and tolerance . 3
7.2 Tolerance on length. 3
8 Physical properties. 4
8.1 Plastic compounds. 4
8.2 Performance requirements for finished hose. 4
8.2.1 Hydrostatic requirements at standard laboratory temperature . 4
8.2.2 Hydrostatic-pressure requirements at 55 °C . 5
8.2.3 Adhesion test . 5
8.2.4 Bending test . 6
8.2.5 Exposure to laboratory light sources. 6
8.2.6 Abrasion test . 7
9 Frequency of testing. 7
10 Test report . 7
11 Marking . 7
12 Recommendations for packaging and storage . 7
Annex A (normative) Abrasion test . 8
Annex B (normative) Type approval and routine testing. 10
Annex C (informative) Production tests. 11
Annex D (informative) Couplings and end fittings. 12
© ISO 2007 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 8029:2011
ISO 8029:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8029 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Hoses (rubber and plastics).
This second edition cancels and replaces the first edition (ISO 8029:1985), which has been technically revised.
iv © ISO 2007 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 8029:2011
ISO 8029:2007(E)
Introduction
This International Standard has been prepared to provide minimum requirements for the satisfactory
performance of textile-reinforced thermoplastic collapsible water hose, for discharge applications, conveying
water, aqueous sludge or slurries.
In view of such applications, requirements, and the corresponding tests, have been specified for exposure to
laboratory light sources (see 8.2.5) and for abrasion resistance (see 8.2.6).
© ISO 2007 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 8029:2011
---------------------- Page: 12 ----------------------
SIST EN ISO 8029:2011
INTERNATIONAL STANDARD ISO 8029:2007(E)
Plastics hose — General-purpose collapsible water hose,
textile-reinforced — Specification
1 Scope
This International Standard specifies the requirements for four types of textile-reinforced thermoplastics
collapsible water hoses for general applications for use in the temperature range of −10 °C to +55 °C.
Such hoses are classified into four types, as follows:
⎯ low pressure, designed for a maximum working pressure of up to 4,0 bar at 23 °C and up to 2,0 bar at
55 °C;
⎯ medium pressure, for a maximum working pressure of up to 7,0 bar at 23 °C and up to 3,6 bar at 55 °C;
⎯ high pressure, for a maximum working pressure of up to 10,0 bar at 23 °C and up to 5,1 bar at 55 °C;
⎯ extra-high pressure, for a maximum working pressure of up to 15,5 bar at 23 °C and up to 7,9 bar at
55 °C.
This standard does not apply to products used for fire-fighting or the conveyance of drinking water.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3, Preferred numbers — Series of preferred numbers
ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and
tolerances on cut-to-length hoses
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
1)
ISO 1746:— , Rubber or plastics hoses and tubing — Bending tests
ISO 4892-2, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
ISO 4892-3, Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV lamps
ISO 4892-4, Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc
lamps
1) To be published. (Revision of ISO 1746:1998)
© ISO 2007 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 8029:2011
ISO 8029:2007(E)
ISO 8033, Rubber and plastics hose — Determination of adhesion between components
ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
ISO 8331, Rubber and plastics hoses and hose assemblies — Guidelines for selection, storage, use and
maintenance
ISO 9352, Plastics — Determination of resistance to wear by abrasive wheels
ISO/TR 17784:2003, Rubber and plastics hoses and hose assemblies — Guide for use by purchasers,
assemblers, installers and operating personnel
ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test
methods
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
4 Classification
Hoses are designated as one of the following four types depending on their pressure rating at the specified
temperatures:
⎯ Type A: Low working pressure hose, designed for a maximum working pressure of up to 4,0 bar at 23 °C
and up to 2,0 bar at 55 °C;
⎯ Type B: Medium working pressure hose, designed for a maximum working pressure of up to 7
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Tuyaux plastiques - Tuyaux d'eau écrasables d'usage général renforcés textiles - Spécifications (ISO 8029:2007)Plastics hose - General-purpose collapsible water hose, textile-reinforced - Specification (ISO 8029:2007)23.040.70Gumene cevi in armatureHoses and hose assembliesICS:Ta slovenski standard je istoveten z:FprEN ISO 8029kSIST FprEN ISO 8029:2010en01-maj-2010kSIST FprEN ISO 8029:2010SLOVENSKI
STANDARD
kSIST FprEN ISO 8029:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 8029
February 2010 ICS 23.040.70 Will supersede EN 28029:1993English Version
Plastics hose - General-purpose collapsible water hose, textile-reinforced - Specification (ISO 8029:2007)
Tuyaux plastiques - Tuyaux d'eau écrasables d'usage général renforcés textiles - Spécifications (ISO 8029:2007)
This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 218.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN ISO 8029:2010: EkSIST FprEN ISO 8029:2010
FprEN ISO 8029:2010 (E) 2 Contents Page Foreword .3 kSIST FprEN ISO 8029:2010
FprEN ISO 8029:2010 (E) 3 Foreword The text of ISO 8029:2007 has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” of the International Organization for Standardization (ISO) and has been taken over as FprEN ISO 8029:2010 by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 28029:1993. Endorsement notice The text of ISO 8029:2007 has been approved by CEN as a FprEN ISO 8029:2010 without any modification.
kSIST FprEN ISO 8029:2010
kSIST FprEN ISO 8029:2010
Reference numberISO 8029:2007(E)© ISO 2007
INTERNATIONAL STANDARD ISO8029Second edition2007-06-15Plastics hose — General-purpose collapsible water hose, textile-reinforced — Specification Tuyaux plastiques — Tuyaux d'eau écrasables d'usage général renforcés textiles — Spécifications
kSIST FprEN ISO 8029:2010
ISO 8029:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii
© ISO 2007 – All rights reserved
kSIST FprEN ISO 8029:2010
ISO 8029:2007(E) © ISO 2007 – All rights reserved iiiContents Page Foreword.iv Introduction.v 1 Scope.1 2 Normative references.1 3 Terms and definitions.2 4 Classification.2 5 Couplings and end fittings.2 6 Materials and construction.2 7 Dimensions and tolerances.3 7.1 Inside diameter and tolerance.3 7.2 Tolerance on length.3 8 Physical properties.4 8.1 Plastic compounds.4 8.2 Performance requirements for finished hose.4 8.2.1 Hydrostatic requirements at standard laboratory temperature.4 8.2.2 Hydrostatic-pressure requirements at 55 °C.5 8.2.3 Adhesion test.5 8.2.4 Bending test.6 8.2.5 Exposure to laboratory light sources.6 8.2.6 Abrasion test.7 9 Frequency of testing.7 10 Test report.7 11 Marking.7 12 Recommendations for packaging and storage.7 Annex A (normative)
Abrasion test.8 Annex B (normative)
Type approval and routine testing.10 Annex C (informative)
Production tests.11 Annex D (informative)
Couplings and end fittings.12
kSIST FprEN ISO 8029:2010
ISO 8029:2007(E) iv © ISO 2007 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8029 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics). This second edition cancels and replaces the first edition (ISO 8029:1985), which has been technically revised. kSIST FprEN ISO 8029:2010
ISO 8029:2007(E) © ISO 2007 – All rights reserved vIntroduction This International Standard has been prepared to provide minimum requirements for the satisfactory performance of textile-reinforced thermoplastic collapsible water hose, for discharge applications, conveying water, aqueous sludge or slurries. In view of such applications, requirements, and the corresponding tests, have been specified for exposure to laboratory light sources (see 8.2.5) and for abrasion resistance (see 8.2.6). kSIST FprEN ISO 8029:2010
kSIST FprEN ISO 8029:2010
INTERNATIONAL STANDARD ISO 8029:2007(E) © ISO 2007 – All rights reserved 1Plastics hose — General-purpose collapsible water hose, textile-reinforced — Specification 1 Scope This International Standard specifies the requirements for four types of textile-reinforced thermoplastics collapsible water hoses for general applications for use in the temperature range of −10 °C to +55 °C. Such hoses are classified into four types, as follows: ⎯ low pressure, designed for a maximum working pressure of up to 4,0 bar at 23 °C and up to 2,0 bar at 55 °C; ⎯ medium pressure, for a maximum working pressure of up to 7,0 bar at 23 °C and up to 3,6 bar at 55 °C; ⎯ high pressure, for a maximum working pressure of up to 10,0 bar at 23 °C and up to 5,1 bar at 55 °C; ⎯ extra-high pressure, for a maximum working pressure of up to 15,5 bar at 23 °C and up to 7,9 bar at 55 °C. This standard does not apply to products used for fire-fighting or the conveyance of drinking water. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3, Preferred numbers — Series of preferred numbers ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing ISO 1746:—1), Rubber or plastics hoses and tubing — Bending tests ISO 4892-2, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps ISO 4892-3, Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV lamps ISO 4892-4, Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps
1) To be published. (Revision of ISO 1746:1998) kSIST FprEN ISO 8029:2010
ISO 8029:2007(E) 2 © ISO 2007 – All rights reserved ISO 8033, Rubber and plastics hose — Determination of adhesion between components ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary ISO 8331, Rubber and plastics hoses and hose assemblies — Guidelines for selection, storage, use and maintenance ISO 9352, Plastics — Determination of resistance to wear by abrasive wheels ISO/TR 17784:2003, Rubber and plastics hoses and hose assemblies — Guide for use by purchasers, assemblers, installers and operating personnel ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test methods 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 8330 apply. 4 Classification Hoses are designated as one of the following four types depending on their pressure rating at the specified temperatures: ⎯ Type A: Low working pressure hose, designed for a maximum working pressure of up to 4,0 bar at 23 °C and up to 2,0 bar at 55 °C; ⎯ Type B: Medium working pressure hose, designed for a maximum working pressure of up to 7,0 bar at 23 °C and up to 3,6 bar at 55 °C; ⎯ Type C: High working pressure hose, designed for a maximum working pressure of up to 10,0 bar at 23 °C and up to 5,1 bar at 55 °C; ⎯ Type D: Extra high working pressure hose, designed for a maximum working pressure of up to 15,5 bar at 23 °C and up to 7,9 bar at 55 °C. 5 Couplings and end fittings Hoses may be fitted with the appropriate coupling type and the end fitting to form hose assemblies. NOTE Guidance on coupling type is given in Annex D and ISO/TR 17784:2003, Clause 7: Couplings. 6 Materials and constructi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.