SIST EN 60974-6:2003
(Main)Arc welding equipment -- Part 6: Limited duty manual metal arc welding power sources
Arc welding equipment -- Part 6: Limited duty manual metal arc welding power sources
Specifies safety requirements for construction and performance requirements of welding power sources, limited to a rated maximum welding current of 160 A. These welding power sources are mainly used by laymen.
Lichtbogenschweißeinrichtungen -- Teil 6: Schweißstromquellen mit begrenzter Einschaltdauer
Matériel de soudage à l'arc -- Partie 6: Sources de courant de soudage manuel à l'arc metallique à service limité
Spécifie les exigences de sécurité pour la construction et les exigences de performance pour les sources de courant de soudage limité à un courant assigné maximal de soudage de 160 A. Ces sources de courant de soudage sont principalement utilisées par des non professionnels.
Arc welding equipment - Part 6: Limited duty manual metal arc welding power sources
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 60974-6:2003
STANDARD
oktober 2003
Arc welding equipment - Part 6: Limited duty manual metal arc welding power
sources
ICS 25.160.30 Referenčna številka
SIST EN 60974-6:2003(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 60974-6
NORME EUROPÉENNE
EUROPÄISCHE NORM April 2003
ICS 25.160.30
English version
Arc welding equipment
Part 6: Limited duty manual metal arc welding power sources
(IEC 60974-6:2003)
Matériel de soudage à l'arc Lichtbogenschweißeinrichtungen
Partie 6: Sources de courant de soudage Teil 6: Schweißstromquellen
manuel à l'arc metallique à service limité mit begrenzter Einschaltdauer
(CEI 60974-6:2003) (IEC 60974-6:2003)
This European Standard was approved by CENELEC on 2003-03-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60974-6:2003 E
---------------------- Page: 2 ----------------------
EN 60974-6:2003 - 2 -
Foreword
The text of document 26/247/FDIS, future edition 1 of IEC 60974-6, prepared by IEC TC 26, Electric
welding, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60974-6 on 2003-03-01.
This Part 6 of EN 60974 is to be used in conjunction with EN 60974-1:1998.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.