Plastics - Ethylene-vinyl acetate (EVAC) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21301-1:2019)

1.1 This document establishes a system of designation for ethylene-vinyl acetate thermoplastic
material, which can be used as the basis for specifications.
1.2 The types of ethylene-vinyl acetate (EVAC) plastic are differentiated from each other by a
classification system based on appropriate levels of the following designatory properties:
a) vinyl acetate content;
b) melt mass-flow rate;
and on information about the intended application and/or method of processing, important properties,
additives, colorants, fillers and reinforcing materials.
1.3 This document is applicable to all ethylene vinyl acetate copolymers containing from a mass
fraction from 3 % to 50 % (approximately 25 % molar) of vinyl acetate.
It applies to materials ready for normal use in the form of powder, granules or pellets and to materials
unmodified or modified by colorants, additives, fillers, etc.
1.4 It is not intended to imply that materials having the same designation give necessarily the same
performance. This document does not provide engineering data, performance data or data on processing
conditions which can be required to specify a material for a particular application and/or method of
processing.
If such additional properties are required, they are determined in accordance with the test methods
specified in ISO 21301-2, if suitable.
1.5 In order to specify a thermoplastic material for a particular application or to ensure reproducible
processing, additional requirements can be given in data block 5 (see 4.1).

Kunststoffe - Ethylen-Vinylacetat (E/VAC)-Werkstoffe - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 21301-1:2019)

Plastiques - Matériaux à base de copolymères éthylène/acétate de vinyle (EVAC) pour moulage et extrusion - Partie 1: Système de désignation et base de spécification (ISO 21301-1:2019)

1.1    Le présent document établit un système de désignation des matériaux thermoplastiques à base de copolymère éthylène/acétate de vinyle qui peut être utilisé comme base pour les spécifications.
1.2    Les types de plastiques à base de copolymère éthylène/acétate de vinyle (EVAC) sont différenciés les uns des autres par un système de classification fondé sur des niveaux appropriés des propriétés de désignation suivantes:
a)    teneur en acétate de vinyle;
b)    indice de fluidité à chaud en masse;
et des informations sur l'application prévue et/ou la méthode de mise en œuvre, les propriétés importantes, les additifs, les colorants, les charges et les matériaux de renfort.
1.3    Le présent document est applicable à tous les copolymères éthylène/acétate de vinyle contenant une fraction massique de 3 % à 50 % (approximativement 25 % molaire) d'acétate de vinyle.
Il s'applique aux matériaux prêts à l'emploi dans le cadre d'une utilisation normale sous la forme de poudre, granulés ou grains et aux matériaux non modifiés ou modifiés par des colorants, additifs, charges, etc.
1.4    Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les mêmes performances. Le présent document ne comporte pas de données sur la conception, la performance ou les conditions de mise en œuvre qui peuvent être exigées pour spécifier un matériau pour une application et/ou une méthode de mise en œuvre particulière.
Si de telles caractéristiques supplémentaires sont nécessaires, elles sont déterminées conformément aux méthodes d'essai spécifiées dans l'ISO 21301‑2, s'il y a lieu.
1.5    Afin de spécifier un matériau thermoplastique pour une application particulière ou d'assurer une méthode de mise en œuvre reproductible, des exigences supplémentaires peuvent être codées dans le bloc de données 5 (voir 4.1).

Polimerni materiali - Materiali na osnovi kopolimerov etilen/vinilacetata (EVAC) za oblikovanje in ekstrudiranje - 1. del: Sistem označevanja in podlage za specifikacije (ISO 21301-1:2019)

1.1 Ta dokument določa sistem označevanja plastomernega materiala na osnovi kopolimerov etilen/vinilacetata, ki ga je mogoče uporabiti kot podlago za specifikacije.
1.2 Vrste kopolimerov etilen/vinilacetata (EVAC) se ločujejo glede na sistem razvrščanja, ki temelji na ustreznih ravneh označevalnih lastnosti:
a) vsebnost etilen/vinilacetata;
b) masni pretok taline;
ter informacijah o predvideni uporabi in/ali metodi obdelave, pomembnih lastnostih, aditivih, barvilih, polnilih in materialih za ojačanje.
1.3 Ta dokument se uporablja za vse kopolimere etilen/vinilacetata, katerih masni delež vinilacetata je 3–50 % (približno 25 % molarnega).
Uporablja se za materiale v obliki praška, granul ali peletov, pripravljene za običajno uporabo, in materiale, nespremenjene ali spremenjene z barvili, aditivi, polnili itd.
1.4 Materiali z enako oznako nimajo nujno tudi enakih
lastnosti. Ta dokument ne podaja tehničnih podatkov, podatkov o delovanju ali podatkov o pogojih obdelave, ki so morda potrebni za določitev materiala za določeno uporabo in/ali metodo obdelave.
Če so take dodatne lastnosti zahtevane, jih je treba določiti v skladu s preskusnimi metodami
iz standarda ISO 21301-2, če je to primerno.
1.5 Zahteve za določanje plastomernega materiala za določeno uporabo ali zagotavljanje ponovljive
obdelave so podane v podatkovnem bloku 5 (glej točko 4.1).

General Information

Status
Published
Public Enquiry End Date
11-Sep-2017
Publication Date
27-Mar-2019
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
15-Mar-2019
Due Date
20-May-2019
Completion Date
28-Mar-2019

Relations

Buy Standard

Standard
EN ISO 21301-1:2019
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 21301-1:2019
01-maj-2019
1DGRPHãþD
SIST EN ISO 4613-1:2000
3ROLPHUQLPDWHULDOL0DWHULDOLQDRVQRYLNRSROLPHURYHWLOHQYLQLODFHWDWD (9$& ]D
REOLNRYDQMHLQHNVWUXGLUDQMHGHO6LVWHPR]QDþHYDQMDLQSRGODJH]D
VSHFLILNDFLMH ,62
Plastics - Ethylene-vinyl acetate (EVAC) moulding and extrusion materials - Part 1:
Designation system and basis for specifications (ISO 21301-1:2019)
Kunststoffe - Ethylen-Vinylacetat (E/VAC)-Werkstoffe - Teil 1: Bezeichnungssystem und
Basis für Spezifikationen (ISO 21301-1:2019)
Plastiques - Matériaux à base de copolymères éthylène/acétate de vinyle (EVAC) pour
moulage et extrusion - Partie 1: Système de désignation et base de spécification (ISO
21301-1:2019)
Ta slovenski standard je istoveten z: EN ISO 21301-1:2019
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 21301-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 21301-1:2019

---------------------- Page: 2 ----------------------

SIST EN ISO 21301-1:2019


EN ISO 21301-1
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2019
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 4613-1:1999
English Version

Plastics - Ethylene-vinyl acetate (EVAC) moulding and
extrusion materials - Part 1: Designation system and basis
for specifications (ISO 21301-1:2019)
Plastiques - Matériaux à base de copolymères Kunststoffe - Ethylen-Vinylacetat (E/VAC)-Werkstoffe -
éthylène/acétate de vinyle (EVAC) pour moulage et Teil 1: Bezeichnungssystem und Basis für
extrusion - Partie 1: Système de désignation et base de Spezifikationen (ISO 21301-1:2019)
spécification (ISO 21301-1:2019)
This European Standard was approved by CEN on 10 February 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21301-1:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 21301-1:2019
EN ISO 21301-1:2019 (E)
Contents Page
European foreword . 3
Endorsement notice . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 21301-1:2019
EN ISO 21301-1:2019 (E)
European foreword
This document (EN ISO 21301-1:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2019, and conflicting national standards
shall be withdrawn at the latest by September 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4613-1:1999.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 21301-1:2019 has been approved by CEN as EN ISO 21301-1:2019 without any
modification.


3

---------------------- Page: 5 ----------------------

SIST EN ISO 21301-1:2019

---------------------- Page: 6 ----------------------

SIST EN ISO 21301-1:2019
INTERNATIONAL ISO
STANDARD 21301-1
First edition
2019-02
Plastics — Ethylene-vinyl acetate
(EVAC) moulding and extrusion
materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Matériaux à base de copolymères éthylène/acétate de
vinyle (EVAC) pour moulage et extrusion —
Partie 1: Système de désignation et base de spécification
Reference number
ISO 21301-1:2019(E)
©
ISO 2019

---------------------- Page: 7 ----------------------

SIST EN ISO 21301-1:2019
ISO 21301-1:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 21301-1:2019
ISO 21301-1:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Designation system . 2
4.1 General . 2
4.2 Data block 1 . 2
4.3 Data block 2 . 3
4.4 Data block 3 . 3
4.5 Data block 4 . 4
4.5.1 General. 4
4.5.2 Melt mass-flow rate . 4
4.6 Data block 5 . 5
5 Examples of designations . 6
© ISO 2019 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 21301-1:2019
ISO 21301-1:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61 Plastics, Subcommittee SC 9,
Thermoplastic materials.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
This first edition of ISO 21301-1 cancels and replaces the second edition of ISO 4613-1:1993, which has
been technically revised. The main changes compared to the previous edition are as follows:
— a new designation system has been introduced;
— the range of MFR has been added.
The revised designation system is published under a new ISO number, as many existing documents
refer to ISO 4613-1.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.