Aerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Part 001: Basic requirements

This European Standard specifies the basic requirements for a two component polyurethane finish, available in a range of colours and levels of gloss, to be applied over a primer for aerospace applications. The properties specified in this standard are obtained on defined aluminium alloy test pieces prepared in accordance with EN 3837 Procedure A and EN 23270 and painted with primer to EN 2435-002. The ability of the material to be used for a specific application (e.g. alternative substrate, alternative primer, specific drying conditions etc.) shall be determined by supplementary tests to confirm that the requirements of this standard are met.

Luft- und Raumfahrt - Beschichtungsstoffe - Zweikomponenten, Polyurethan-Decklack, Kalthärtend - Teil 001: Grundlegende Anforderungen

Diese Europäische Norm legt die grundlegenden Anforderungen an eine Zweikomponenten-Polyurethan-Deckbeschichtung fest, die in einer Auswahl verschiedener Farben und Glanzgrade erhältlich ist und auf einen Primer für Anwendungen in der Luft- und Raumfahrt aufzubringen ist.
Die in dieser Europäischen Norm festgelegten Eigenschaften werden an festgelegten Probenkörpern aus Aluminiumlegierung ermittelt, die nach EN 3837, Verfahren A sowie nach EN 23270 hergestellt und mit Primer nach EN 2435 002 beschichtet wurden. Die Eignung des Werkstoffes für eine bestimmte Anwendung (z. B. alternativer Trägerwerkstoff, alternativer Primer, bestimmte Trocknungsbedingungen usw.) ist durch zusätzliche Prüfungen zu ermitteln, um zu bestätigen, dass die Anforderungen dieser Norm erfüllt werden.

Série aérospatiale - Peintures et vernis - Peinture de finition polyuréthane, à deux composants polymérisant à température ambiante - Partie 001: Exigences générales

Aeronavtika - Barve in laki - Dvokomponentni poliuretanski končni premaz, ki se suši pri sobni temperaturi - 001. del: Osnovne zahteve

Ta evropski standard določa osnovne zahteve za dvokomponentni poliuretanski končni premaz, ki je na voljo v različnih barvah in stopnjah sijaja, ki se nanese čez temeljni premaz za uporabo v aeronavtiki. Lastnosti, določene v tem standardu, so pridobljene na definiranih preskusnih kosih aluminijeve zlitine, pripravljenih v skladu z EN 3837, Postopkom A in EN 23270 ter premazane s temeljnim premazom v EN 2435-002. Sposobnost materiala, da se uporablja za posebna področja uporabe (npr. alternativni substrat, alternativni temeljni premaz, posebni pogoji sušenja itd.), se določi z dodatnimi preskusi, s katerimi se potrdi, da so zahteve tega standarda izpolnjene.

General Information

Status
Published
Publication Date
02-Nov-2010
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
15-Oct-2010
Due Date
20-Dec-2010
Completion Date
03-Nov-2010

Buy Standard

Standard
EN 2434-001:2010
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Beschichtungsstoffe - Zweikomponenten, Polyurethan-Decklack, Kalthärtend - Teil 001: Grundlegende AnforderungenSérie aérospatiale - Peintures et vernis - Peinture de finition polyuréthane, à deux composants polymérisant à température ambiante - Partie 001: Exigences généralesAerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Part 001: Basic requirements49.040Prevleke in z njimi povezani postopki, ki se uporabljajo v letalski in vesoljski industrijiCoatings and related processes used in aerospace industryICS:Ta slovenski standard je istoveten z:EN 2434-001:2010SIST EN 2434-001:2010en,de01-december-2010SIST EN 2434-001:2010SLOVENSKI
STANDARD



SIST EN 2434-001:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2434-001
September 2010 ICS 49.040 English Version
Aerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Part 001: Basic requirements
Série aérospatiale - Peintures et vernis - Peinture de finition polyuréthane, à deux composants polymérisant à température ambiante - Partie 001: Exigences générales
Luft- und Raumfahrt - Beschichtungsstoffe - Zweikomponenten- Polyurethan-Decklack, kalthärtend - Teil 001: Grundlegende Anforderungen This European Standard was approved by CEN on 6 February 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2434-001:2010: ESIST EN 2434-001:2010



EN 2434-001:2010 (E) 2 Contents Page Foreword .3Introduction .41Scope .42Normative references .43Terms and definitions .54Classification .55Batch release and qualification testing .55.1Batch release testing .55.2Qualification tests .5 SIST EN 2434-001:2010



EN 2434-001:2010 (E) 3 Foreword This document (EN 2434-001:2010) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at the latest by March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 2434-001:2010



EN 2434-001:2010 (E) 4 Introduction Definition of subcase numbering in Table 2 to Table 5 is given in EN 7000-9. 1 Scope This European Standard specifies the basic requirements for a two component polyurethane finish, available in a range of colours and levels of gloss, to be applied over a primer for aerospace applications. The properties specified in this standard are obtained on defined aluminium alloy test pieces prepared in accordance with EN 3837 Procedure A and EN 23270 and painted with primer to EN 2435-002. The ability of the material to be used for a specific application (e.g. alternative substrate, alternative primer, specific drying conditions etc.) shall be determined by supplementary tests to confirm that the requirements of this standard are met. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2334, Aerospace series – Chromic-sulphuric acid pickle of aluminium and aluminium alloys EN 2379, Aerospace series – Fluids for assessment of non-metallic materials1) EN 2435-001, Aerospace series – Paints and varnishes – Corrosion resistant chromated two component cold curing primer – Part 001: Minimum requirements
EN 2435-002, Aerospace series – Paints and varnishes – Corrosion resistant chromat
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.