SIST EN 13757-1:2015
(Main)Communication systems for meters - Part 1: Data exchange
Communication systems for meters - Part 1: Data exchange
This European Standard specifies data exchange and communications for meters and remote reading of meters in a generic way.
This European Standard establishes a protocol specification for the Application Layer for meters and establishes several protocols for meter communications which may be applied depending on the application being fulfilled.
NOTE Electricity meters are not covered by this standard, as the standardization of remote readout of electricity meters is a task for CENELEC.
Kommunikationssysteme für Zähler - Teil 1: Datenaustausch
Diese Europäische Norm legt den Datenaustausch und die Kommunikation für Zähler und deren Fern¬ablesung in allgemeiner Weise fest.
Diese Europäische Norm legt eine Protokollspezifikation für die Anwendungsschicht für Zähler und verschie¬dene Protokolle für die Zählerkommunikation fest, die in Abhängigkeit von der auszuführenden Anwendung angewendet werden können.
ANMERKUNG Elektrizitätszähler werden von dieser Norm nicht abgedeckt, denn die Normung für die Fernablesung von Elektrizitätszählern obliegt CENELEC.
Systèmes de communication et de télérelevé de compteurs - Partie 1 : Echange de données
La présente Norme européenne définit l’échange de données et les communications relatifs aux compteurs et au télérelevé de compteurs, de manière générale.
La présente Norme européenne établit une spécification de protocole pour la couche application des compteurs ainsi que plusieurs protocoles pour les communications des compteurs qui peuvent être appliqués selon l’application en cours de réalisation.
NOTE Les compteurs d’énergie électrique ne sont pas concernés par la présente norme, car la normalisation du télérelevé des compteurs d’énergie électrique est assurée par le CENELEC.
Komunikacijski sistemi za merilnike - 1. del: Izmenjava podatkov
Ta evropski standard določa izmenjavo podatkov in komunikacijo za merilnike ter daljinsko odčitavanje merilnikov na generičen način.
Ta evropski standard določa protokolsko specifikacijo za aplikacijski nivo za merilnike in določa več protokolov za komunikacijo z merilniki, ki se lahko uporabijo glede na zadevno uporabo.
OPOMBA: Merilniki električne energije niso obravnavani v tem standardu, saj je standardizacija daljinskega odčitavanja merilnikov električne energije naloga za CENELEC.
General Information
Relations
Frequently Asked Questions
SIST EN 13757-1:2015 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Communication systems for meters - Part 1: Data exchange". This standard covers: This European Standard specifies data exchange and communications for meters and remote reading of meters in a generic way. This European Standard establishes a protocol specification for the Application Layer for meters and establishes several protocols for meter communications which may be applied depending on the application being fulfilled. NOTE Electricity meters are not covered by this standard, as the standardization of remote readout of electricity meters is a task for CENELEC.
This European Standard specifies data exchange and communications for meters and remote reading of meters in a generic way. This European Standard establishes a protocol specification for the Application Layer for meters and establishes several protocols for meter communications which may be applied depending on the application being fulfilled. NOTE Electricity meters are not covered by this standard, as the standardization of remote readout of electricity meters is a task for CENELEC.
SIST EN 13757-1:2015 is classified under the following ICS (International Classification for Standards) categories: 33.200 - Telecontrol. Telemetering; 35.100.70 - Application layer. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 13757-1:2015 has the following relationships with other standards: It is inter standard links to SIST EN 13757-1:2004, SIST EN 13757-1:2022. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 13757-1:2015 is associated with the following European legislation: Standardization Mandates: M/441, M/490. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 13757-1:2015 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Komunikacijski sistemi za merilnike - 1. del: Izmenjava podatkovKommunikationssysteme für Zähler - Teil 1: DatenaustauschSystèmes de communication et de télérelevé de compteurs - Partie 1 : Echange de donnéesCommunication systems for meters - Part 1: Data exchange35.100.70Uporabniški slojApplication layer33.200Daljinsko krmiljenje, daljinske meritve (telemetrija)Telecontrol. TelemeteringICS:Ta slovenski standard je istoveten z:EN 13757-1:2014SIST EN 13757-1:2015en,fr,de01-januar-2015SIST EN 13757-1:2015SLOVENSKI
STANDARDSIST EN 13757-1:20041DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13757-1
October 2014 ICS 33.200; 35.100.70 Supersedes EN 13757-1:2002English Version
Communication systems for meters - Part 1: Data exchange
Systèmes de communication et de télérelevé de compteurs - Partie 1 : Echange de données
Kommunikationssysteme für Zähler - Teil 1: Datenaustausch This European Standard was approved by CEN on 30 August 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13757-1:2014 ESIST EN 13757-1:2015
Basic class meters . 115 A.1 General . 115 A.2 Basic requirements for Heat Cost Allocators . 115 A.3 Basic requirements for Heat/ Cooling meters . 116 A.4 Basic requirements for Gas meters . 116 A.5 Basic requirements for Cold/ Hot water meters . 117 Annex B (informative)
DLMS Glossary. 118 B.1 Introduction . 118 B.2 Activation mask . 118 B.3 Activity calendar . 118 B.4 Association LN . 118 B.5 Association SN . 118 B.6 Automatic capturing . 118 B.7 Billing Period in COSEM . 118 B.8 Capture . 119 B.9 Channel . 119 B.10 Clock . 119 B.11 Current and last average value objects . 120 B.12 Date and time . 120 B.13 Daylight saving . 120 B.14 Demand Register . 120 B.15 Device ID . 122 B.16 Error values . 122 B.17 High level security . 123 B.18 Interface modelling . 123 B.19 I/O Control Signals. 123 B.20 Interoperability . 123 B.21 Logical device . 123 B.22 Logical name referencing . 124 B.23 Low level security . 124 B.24 Manufacturer defined ID-s . 124 B.25 Manufacturer specific abstract objects . 124 B.26 Manufacturer specific class id . 124 B.27 Manufacturer specific data and parameters . 124 B.28 Manufacturer specific OBIS codes . 125 B.29 Maximum and minimum value objects . 125 B.30 Measurement of different media . 125 B.31 Measurement method and tariffs . 125 B.32 Measurement values series . 125 B.33 Missing measurement values . 125 B.34 Node . 125 B.35 Password . 126 B.36 Physical device . 126 B.37 Power failure handling . 126 SIST EN 13757-1:2015
Gas Volume Conversion . 135 C.1 Introduction . 135 C.2 Foreword to abstract data model of gas volume converter . 135 C.3 Abstract data model of gas volume converter — Common objects in gas conversion and energy calculation . 136 C.4 Principle of measurement for volume conversion and energy calculation . 137 C.5 Data flow in volume conversion and energy calculation . 139 Annex D (normative)
Country specific identifiers . 140 Bibliography . 142
Tables Table 1 — Typical Client Access Levels . 21 Table 2 — M-Bus Port Setup Object . 44 Table 3 — Description of Class ID “Data” . 45 Table 4 — Tunnelling, Value group E . 46 SIST EN 13757-1:2015
> 0, 96 . 99 (HCA objects) . 71 Table 21 — OBIS codes for general and service entry objects – HCA . 71 Table 22 — OBIS codes for error register objects – HCA. 72 Table 23 — OBIS codes for data profile objects – HCA . 73 Table 24 — OBIS codes for HCA related objects (examples) . 73 Table 25 — Value group C codes where A = 5 or A = 6 (Heat/cooling objects) . 74 Table 26 — Value group D codes where A = 5 or A = 6 and C <
> 0, 96…99 (Heat/cooling objects) . 75 Table 27 — OBIS codes for general and service entry objects – Heat/cooling . 76 Table 28 — OBIS codes for error register objects – Heat/ cooling . 78 Table 29 — OBIS codes for data profile objects – Heat/ cooling . 78 Table 30 — OBIS codes for heat/ cooling related objects (examples) . 79 Table 31 — Value group C codes where A = 7 – Gas . 81 Table 32 — Value group D codes for Gas – Indexes and index differences (A = 7, C = 1…8, 11…16, 21…26, 31…36, 61…66) . 84 Table 33 — Value group D codes – Gas – Flow rate: A = 7, C = 43 . 88 Table 34 — Value group D codes – Gas – Process values (A = 7, C = 41, 42, 44…49) . 90 Table 35 — Value group D codes – Gas – Correction, conversion and compressibility values (A = 7, C = 51…55). 93 Table 36 — Value group D codes – Gas – Natural gas analysis values (A = 7, C = 70) . 93 Table 37 — Value group E codes – Gas – Indexes and index differences – Tariff rates for A = 7, C = 1.8, 11.16, 21.26, 31.36, 61.66, D = 0…3, 6…98 . 95 Table 38 — Value group E codes – Gas – Correction, conversion and compressibility values – Averages: A = 7, C = 51.55, D = 0, 2, 3, 10, 11 . 95 Table 39 — Value group E codes – Gas – Calculation methods A = 7, C = 51.55, D = 12 . 97 SIST EN 13757-1:2015
> 0, 96…99 (Water volume objects) . 109 Table 47 — OBIS codes for general and service entry objects – Water . 110 Table 48 — OBIS codes for error register objects – Water . 111 Table 49 — OBIS codes for data profile objects – Water . 111 Table 50 — OBIS codes for water related objects (examples) . 111 Table 51 — Value group C codes – Other media. 112 Table 52 — Example of display code replacement – Value group C. 113 Table 53 — Value group F – Billing periods . 114 Table A.1 — Basic requirements for Heat Cost Allocators . 115 Table A.2 — Basic requirements for Heat/ Cooling meters . 116 Table A.3 — Basic requirements for Gas meters . 116 Table A.4 — Basic requirements for Cold/ Hot water meters . 117 Table B.1 — Enumerated values for physical units . 132 Table C.1 — OBIS-Value group A = 7, B = X, E = 0, F = FF . 136 Table D.1 — Value group D codes — Country specific identifiers C = 94 . 140
Figures Figure 1 — The OSI 7-layer model . 16 Figure 2 — Connection method independent Application Layers . 17 Figure 3 — IEC 3-layer model . 17 Figure 4 — Link and Physical layers in the 3 layer model . 18 Figure 5 — Network Architecture — The architecture diagram in CEN/CLC/ETSI TR 50572 . 22 Figure 6 — System and physical architecture. 24 Figure 7 — Basic Metering architecture . 25 Figure 8 — Scope of Companion Specifications . 27 Figure 9 — Companion Specification in relation to lower layers (3 layer model) . 28 Figure 10 — An interface class and its instances . 29 Figure 11 — Full protocol stack . 30 Figure 12 — Typical PSTN configuration . 33 Figure 13 — The location of the Physical Layer. 34 Figure 14 — COSEM over IP . 36 Figure 15 — EN 60870-5-2-related Transport PDU format . 40 SIST EN 13757-1:2015
...
기사 제목: SIST EN 13757-1:2015 - 미터를 위한 통신 시스템 - 파트 1: 데이터 교환 기사 내용: 이 유럽 표준은 미터와 미터의 원격 독서를 위한 데이터 교환과 통신을 일반적인 방법으로 규정합니다. 이 유럽 표준은 미터를 위한 응용 계층에 대한 프로토콜 사양을 성립하며, 수행 중인 응용에 따라 적용할 수 있는 여러 미터 통신 프로토콜을 설정합니다. 참고로, 이 표준은 전기 미터를 포함하지 않으며, 전기 미터의 원격 독서 표준화는 CENELEC의 역할입니다.
記事のタイトル: SIST EN 13757-1:2015 - メーターの通信システム - パート1: データの交換 記事の内容: この欧州基準では、メーターおよびメーターの遠隔読み取りのためのデータ交換と通信を一般的な方法で指定しています。 この欧州基準では、メーターのアプリケーション層のためのプロトコル仕様を確立し、対応するアプリケーションに応じて適用される複数のメーター通信プロトコルを設定します。 ただし、この基準は電力メーターには適用されず、電力メーターの遠隔読み取りの標準化はCENELECの責任です。
The article discusses the European Standard SIST EN 13757-1:2015, which focuses on communication systems for meters. The standard provides guidelines for data exchange and remote reading of meters. It establishes protocols for meter communication depending on the application. However, it is important to note that this standard does not cover electricity meters, as the standardization for remote readout of electricity meters is handled by CENELEC.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...