SIST-TS CEN/TS 14578:2004
(Main)Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GPR) based on unsaturated polyester resin (UP) - Recommended practice for installation
Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GPR) based on unsaturated polyester resin (UP) - Recommended practice for installation
This Technical Specification (CEN/TS) specifies recommended practices for installing piping systems made of glass-reinforced thermosetting plastics based on unsaturated polyester resin (GRP-UP), intended to be used for pressure or non-pressure water or sewerage applications. It is applicable to GRP-UP piping systems of nominal sizes from DN 100 to DN 3000 which are intended to be used for the conveyance of liquids at temperatures up to 50 °C and at pressures of 0,5 bar and greater.
NOTE 1 Piping systems conforming to prEN 1796 [4] or prEN 14364 [5] can also be used for above-ground applications provided the influence of the environment and the supports is considered in the design of the pipes and joints.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
Kunststoft-Rohrleitungssysteme für den Wasserversorgung mit oder ohne Druck - Glasfaserverstärkten duroplastischen Kunstoffe (GFK) auf der basis von ungesättigtem Polyesterharz (UP) - Empfohlenes Verfahren zur Verlegung
Diese Technische Spezifikation (CEN/TS) legt Empfehlungen für die Verlegung von Rohrleitungssystemen aus glasfaserverstärkten duroplastischen Kunststoffen auf der Basis von ungesättigtem Polyesterharz (GFK-UP) fest, die für die Wasserversorgung oder für Abwasserkanäle und -leitungen mit oder ohne Druck verwendet werden. Sie ist auf GFK-UP-Rohrleitungssysteme mit einer Nennweite von DN 100 bis DN 3000 anwendbar, die für die Ableitung von Flüssigkeiten bei Temperaturen bis zu 50 °C und Drücken von 0,5 bar oder mehr eingesetzt werden.
ANMERKUNG 1 Rohrleitungssysteme nach prEN 1796 [4] oder prEN 14364 [5] können auch für oberirdische Anwendungen eingesetzt werden, vorausgesetzt, dass der Einfluss der Umgebung und der Auflager bei der Dimensionierung von Rohren und Verbindungen berücksichtigt wurde.
ANMERKUNG 2 Es liegt in der Verantwortung des Anwenders oder des Auftraggebers, eine geeignete Auswahl dieser Kriterien unter Berücksichtigung der eigenen Anforderungen und der geltenden nationalen Festlegungen sowie der Verlegepraktiken oder Kodes zu treffen.
Systemes de canalisations plastiques pour l'adduction d'eau et l'assainissement - Plastiques thermodurcissables renforcés de verre (PRV) a base de résine de polyester non saturé (UP) - Pratique recommandée pour la pose
La présente Spécification Technique, a lire conjointement avec l?ENV 1046 et l?EN 1610, présente un
ensemble de lignes directrices propres a la matiere pour la pose des systemes de canalisations en
polypropylene avec modificateurs minéraux (PP-MD) dans le domaine des branchements et collecteurs
d'assainissement sans pression.
3 enterrés a l'extérieur de la structure des bâtiments (code de zone d'application "U") ;
3 enterrés tant a l'intérieur de la structure des bâtiments (code de zone d'application "D") qu'a l'extérieur de
la structure des bâtiments.
Le type correspondant est reflété dans le marquage des produits par les lettres "U" et "UD".
Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GPR) based on unsaturated polyester resin (UP) - Recommended practice for installation
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 14578:2004
01-maj-2004
1DGRPHãþD
SIST EN 1636-6:1999
Plastics piping systems for water supply or drainage and sewerage - Glass-
reinforced thermosetting plastics (GPR) based on unsaturated polyester resin (UP)
- Recommended practice for installation
Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced
thermosetting plastics (GPR) based on unsaturated polyester resin (UP) -
Recommended practice for installation
Kunststoft-Rohrleitungssysteme für den Wasserversorgung mit oder ohne Druck -
Glasfaserverstärkten duroplastischen Kunstoffe (GFK) auf der basis von ungesättigtem
Polyesterharz (UP) - Empfohlenes Verfahren zur Verlegung
Systemes de canalisations plastiques pour l'adduction d'eau et l'assainissement -
Plastiques thermodurcissables renforcés de verre (PRV) a base de résine de polyester
non saturé (UP) - Pratique recommandée pour la pose
Ta slovenski standard je istoveten z: CEN/TS 14578:2003
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST-TS CEN/TS 14578:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 14578:2004
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 14578:2004
TECHNICAL SPECIFICATION
CEN/TS 14578
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
September 2003
ICS 23.040.01, 91.140.80, 93.030
Supersedes EN 1636-6:1997
English version
Plastics piping systems for water supply or drainage and
sewerage – Glass-reinforced thermosetting plastics (GPR)
based on unsaturated polyester resin (UP) – Recommended
practice for installation
Systèmes de canalisations plastiques pour l’adduction Kunststoft-Rohrleitungssysteme für den Wasserversorgung
d’eau et l’assainissement – Plastiques thermodurcissables mit oder ohne Druck – Glasfaserverstärkten
renforcés de verre (PRV) à base de résine de polyester duroplastischen Kunstoffe (GFK) auf der basis von
non saturé (UP) – Pratique recommandée pour la pose ungesättigtem Polyesterharz (UP) – Empfohlenes
Verfahren zur Verlegung
This Technical Specification (CEN/TS) was approved by CEN on 24 March 2003 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available. It
is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible
conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 14578:2003 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 14578:2004
CEN/TS 14578:2003 (E)
Contents page
Foreword.3
Introduction .4
1 Scope.5
2 Normative references.5
3 Terms and definitions.5
4 Procedures.5
4.1 General.5
4.2 Special conditions for pipes having a nominal stiffness less than SN 1250 .5
5 Specific information and recommendations .5
5.1 General.5
5.2 Special transportation requirements .6
5.3 Maximum storage heights on site .6
5.4 Maximum storage period in direct sunlight .6
5.5 Any climatic conditions requiring special storage .6
5.6 Limiting deflections.6
5.7 Coefficient of linear expansion.6
5.8 Longitudinal tensile modulus and strength.7
5.9 Suitability for use in areas exposed to sunlight.7
5.10 Appropriate jointing system.7
5.11 Cold bending .7
5.12 Permitted rates of loss of water and/or pressure .7
Bibliography .8
2
---------------------- Page: 4 ----------------------
SIST-TS CEN/TS 14578:2004
CEN/TS 14578:2003 (E)
Foreword
This document (CEN/TS 14578:2003) has been prepared by Technical Committee CEN /TC 155, "Plastics piping
systems and ducting systems" the secretariat of which is held by NEN.
[1]
This document supersedes EN 1636-6:1997 .
[2]
It is also the result of a merging of the final draft prEN 1115-6:1997 and the draft European standard
[3]
prEN 1796-6:1995 .
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this CEN Technical Specification: Austria, Belgium, Czech Republic, Denmark,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway,
Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN/TS 14578:2004
CEN/TS 14578:2003 (E)
Introduction
[4] [5]
System Standards prEN 1796 and prEN 14364 specify the properties of a piping system and its components
when made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
intended to be used for pressure and non-pressure water or sewerage applications. A System Standard includes
specifications for pipes, fittings and joints and makes reference to supporting standards covering test methods,
recommended practices for installation (this Technical Specification) and procedures for assessment of conformity.
The committee is preparing a standard to cover matters such as design procedures, determination of long-term
safety factors based on a semi-probabilistic approach, surge allowance and allowable negative pressures fo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.