SIST EN 14894:2006
(Main)LPG equipment and accessories - Cylinder and drum marking
LPG equipment and accessories - Cylinder and drum marking
This European Standard specifies stamp marking requirements for transportable refillable LPG cylinders and metallic drums including:
- Steel LPG cylinders designed and manufactured in accordance with EN 1442, EN 14140, EN 12807 or an equivalent standard or technical code recognised by the Competent Authority.
LPG metallic drums designed and manufactured in accordance with EN 14893 or an equivalent standard or technical code recognised by the Competent Authority.
Welded aluminium LPG cylinders designed and manufactured in accordance with EN 13110 or an equivalent standard or technical code recognised by the Competent Authority.
LPG composite cylinders designed and manufactured in accordance with EN 14427 or an equivalent standard or technical code recognised by the Competent Authority.
NOTE All these types of receptacles are referred to throughout this standard as “cylinders”.
This standard does not specify any requirements for product, hazard or safety-phrase labelling of packaging which may be required to meet ADR or other legislative requirements.
Flüssiggas-Geräte und Ausrüstungsteile - Kennzeichnung von Flüssiggas(LPG)-Flaschen
Diese Europäische Norm legt die Anforderungen an die Stempelung von ortsbeweglichen, wiederbefüllbaren LPG-Flaschen und metallischen Druckfässern fest, einschließlich:
- LPG-Flaschen aus Stahl, gestaltet und hergestellt in Übereinstimmung mit EN 1442, EN 14140, EN 12807 oder einer gleichwertigen Norm oder technischen Regel, die von der zugelassenen Stelle anerkannt wurde;
- metallische LPG-Fässer aus Stahl, gestaltet und hergestellt in Übereinstimmung mit EN 14893 oder einer gleichwertigen Norm oder technischen Regel, die von der zugelassenen Stelle anerkannt wurde;
- geschweißte LPG-Flaschen aus Aluminium, gestaltet und hergestellt in Übereinstimmung mit EN 13110 oder einer gleichwertigen Norm oder technischen Regel, die von der zugelassenen Stelle anerkannt wurde;
- LPG-Flaschen aus Verbundwerkstoffen, gestaltet und hergestellt in Übereinstimmung mit EN 14427 oder einer gleichwertigen Norm oder technischen Regel, die von der zugelassenen Stelle anerkannt wurde.
ANMERKUNG Alle diese Behältnisse werden in der gesamten vorliegenden Norm als "Flaschen" bezeichnet.
Diese Norm legt keine Anforderungen für Produkt, Gefährdungen oder Anbringen von Warnhinweisschildern auf Verpackungen fest, die ADR-Anforderungen oder anderen gesetzlichen Bestimmungen entsprechen müssen.
Équipements pour gaz de pétrole liquéfié et leurs accessoires - Marquage des bouteilles et des futs a pression
La présente Norme européenne prescrit les exigences de marquage s’appliquant aux bouteilles a GPL
transportables rechargeables et aux futs a pression métalliques, incluant :
- les bouteilles a GPL en acier conçues et fabriquées conformément aux normes EN 1442, EN 14140,
EN 12807 ou a une norme équivalente ou un code technique reconnu par l’autorité compétente ;
- les futs a pression métalliques pour GPL conçus et fabriqués conformément a l’EN 14893 ou a une
norme équivalente ou un code technique reconnu par l’autorité compétente ;
- les bouteilles a GPL en aluminium soudées, conçues et fabriquées conformément a l’EN 13110 ou a une
norme équivalente ou un code technique reconnu par l’autorité compétente ;
- les bouteilles a GPL en matériaux composites conçues et fabriquées conformément a l’EN 14427 ou a
une norme équivalente ou un code technique reconnu par l’autorité compétente.
NOTE Dans la présente norme, tous ces types de récipients sont désignés "bouteilles".
La présente norme ne prescrit pas d’exigences, relatives au produit, aux phénomenes dangereux ou a
l’étiquetage de sécurité de l’emballage, pouvant etre requises pour etre conforme a l’ADR ou a toute autre
exigence législative.
Oprema in dodatki za UNP – Označevanje jeklenk in sodov
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.LPG equipment and accessories - Cylinder and drum markingÉquipements pour gaz de pétrole liquéfié et leurs accessoires - Marquage des bouteilles et des futs a pressionFlüssiggas-Geräte und Ausrüstungsteile - Kennzeichnung von Flüssiggas(LPG)-FlaschenTa slovenski standard je istoveten z:EN 14894:2006SIST EN 14894:2006en23.020.30MHNOHQNHPressure vessels, gas cylindersICS:SLOVENSKI
STANDARDSIST EN 14894:200601-oktober-2006
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14894May 2006ICS 23.020.30 English VersionLPG equipment and accessories - Cylinder and drum markingÉquipements pour gaz de pétrole liquéfié et leursaccessoires - Marquage des bouteilles et des fûts àpressionFlüssiggas-Geräte und Ausrüstungsteile - Kennzeichnungvon Flüssiggas(LPG)-FlaschenThis European Standard was approved by CEN on 20 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14894:2006: E
EN 14894:2006 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Terms and definitions.5 3 Symbols and abbreviations.5 4 Application of stamp markings.5 5 Manufacturing stamp markings.7 6 Operational stamp markings.7 7 Certification stamp markings.8 8 Other stamp markings.9 Annex A (informative)
Examples of alternative locations, stamp markings.11 Bibliography.12
EN 14894:2006 (E) 3 Foreword This document (EN 14894:2006) has been prepared by Technical Committee CEN/TC 286 “Liquefied petroleum gas equipment and accessories”, the secretariat of which is held by NSAI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2006, and conflicting national standards shall be withdrawn at the latest by November 2006. This European Standard has been submitted for reference into the RID and/or in the technical annexes of the ADR.
Therefore the standards listed in the normative references and covering basic requirements of the RID/ADR not addressed within the present standard are normative only when the standards themselves are referred to in the RID and/or in the technical annexes of the ADR. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 14894:2006 (E) 4 Introduction This European Standard calls for the use of substances and procedures that may be injurious to health if adequate precautions are not taken. It refers only to technical suitability and does not absolve the user from legal obligations relating to health and safety at any stage. It has been assumed in the drafting of this European Standard that the execution of its provisions is entrusted to appropriately qualified and experienced people.
EN 14894:2006 (E) 5 1 Scope This European Standard specifies stamp marking requirements for transportable refillable LPG cylinders and metallic drums including: Steel LPG cylinders designed and manufactured in accordance with EN 1442, EN 14140, EN 12807 or an equivalent standard or technical code recognised by the Competent Authority. LPG metallic drums designed and manufactured in accordance with EN 14893 or an equivalent standard or technical code recognised by the Competent Authority. Welded aluminium LPG cylinders designed and manufactured in accordance with EN 13110 or an equivalent standard or technical code recognised by the Competent Authority. LPG composite cylinders designed and manufactured in accordance with EN 14427 or an equivalent standard or technical code recognised by the Competent Authority. NOTE All these types of receptacles are referred to throughout this standard as “cylinders”. This standard does not specify any requirements for product, hazard or safety-phrase labelling of packaging which may be required to meet ADR or other legislative requirements. 2 Terms and definitions For the purposes of this document, the following term and definition applies. 2.1 stamp marking permanent or durable markings affixed to the cylinder NOTE The marking information may be supplemented / duplicated by electronic means or other types of coding if required by the operator. 3 Symbols and abbreviations TPED Council Directive 1999/36/EC of 29 April 1999 on transportable pressure equipment 4 Application of stamp markings 4.1 General Stamp markings consist of manufacturing, operational and certification stamp marks and are listed in Clause 5, Clause 6, Clause 7 and Clause 8.
The layout of the marks is covered by 4.3.
Additional markings may be applied if required by other regulations or the technical standard, or when required by the cylinder owner; provided the layout does not cause any confusion in their interpretation and the clarity of the other mandatory markings is not affected. 4.2 Workmanship 4.2.1 All stamp markings shall be affixed clearly, legibly and durably on the cylinder and shall remain legible under all foreseeable operating and ageing conditions.
EN 14894:2006 (E) 6 Markings required to be “permanent” shall be such that they can only be removed with the use of special tools and may be done, for example by hard metal stamping, engraving, casting, embossing, encapsulation or other similar methods. Markings required to be “durable” shall be such that they remain visible for the relevant period of time and may be done, for example by printing, external labelling, stencilling, use of valve hand-wheel insert or other similar methods.
Clause 5, Clause 6, Clause 7 and Clause 8 indicate which markings shall be "permanent (P)" and which may be "durable (D)". NOTE
Markings which are permitted to be durable may be permanently applied if so desired. 4.2.2 For metallic cylinders, the marks shall be located on the shoulder, top end or neck of the cylinder or on a permanently affixed component, e.g. welded nameplate, handle(s), foot ring, shroud etc.
4.2.3 If markings are applied after completion of manufacture or following periodic inspection, by stamping or engraving onto the pressure parts of the cylinder, it shall be demonstrated by fatigue and burst tests in accordance with the original design standard or equivalent, that failure does not initiate in the marking
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.