SIST EN 15182-4:2007
(Main)Hand-held branchpipes for fire service use - Part 4: High pressure branchpipes PN 40
Hand-held branchpipes for fire service use - Part 4: High pressure branchpipes PN 40
In addition to the requirements given in EN 15182-1, this document applies to hand-held high pressure branchpipes (nozzles) PN 40 with a maximum flow rate of 200 l/min at a reference pressure of 6 bar (0,6 MPa). It deals with:
safety requirements;
performance requirements;
test methods;
classification and designation;
operating instructions;
marking and maintenance.
This part of this European Standard applies to branchpipes as defined in Annex A of EN 15182-1:2007.
Strahlrohre für die Brandbekämpfung - Teil 4: Hochdruckstrahlrohre PN 40
4
Zusätzlich zu den in prEN 15182-1 angegebenen Anforderungen gilt dieses Dokument für Hochdruck-strahlrohre
(Düsen) PN 40 mit einer maximalen Durchflussmenge von 200 l/min bei einem Referenzdruck von
6 bar (0,6MPa). Behandelt werden:
.Sicherheitsanforderungen;
.Anforderungen an die Funktion;
.Prüfverfahren;
.Klassifizierung und Bezeichnung;
.Betriebsanleitung;
.Kennzeichnung und Instandhaltung.
Lances a main destinées aux services d'incendie et de secours - Partie 4 : Lances haute pression PN 40
Gasilski ročniki - 4. del: Visokotlačni ročniki PN 40
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Hand-held branchpipes for fire service use - Part 4: High pressure branchpipes PN 40Lances a main destinées aux services d'incendie et de secours - Partie 4 : Lances haute pression PN 40Strahlrohre für die Brandbekämpfung - Teil 4: Hochdruckstrahlrohre PN 40Ta slovenski standard je istoveten z:EN 15182-4:2007SIST EN 15182-4:2007en;fr;de13.220.10Gašenje požaraFire-fightingICS:SLOVENSKI
STANDARDSIST EN 15182-4:200701-julij-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15182-4February 2007ICS 13.220.10 English VersionHand-held branchpipes for fire service use - Part 4: Highpressure branchpipes PN 40Lances à main destinées aux services d'incendie et desecours - Partie 4 : Lances haute pression PN 40Strahlrohre für die Brandbekämpfung - Teil 4:Hochdruckstrahlrohre PN 40This European Standard was approved by CEN on 23 December 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15182-4:2007: E
EN 15182-4:2007 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Requirements.5 5 Testing and proofs.9
EN 15182-4:2007 (E) 3 Foreword This European Standard (EN 15182-4:2007) has been prepared by Technical Committee CEN/TC 192 “Fire service equipment”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2007, and conflicting national standards shall be withdrawn at the latest by August 2007. EN 15182 consists of the following parts, under the general title Hand-held branchpipes for fire service use: Part 1 : Common requirements; Part 2 : Combination branchpipes PN 16; Part 3 : Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16; Part 4: High pressure branchpipes PN 40. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 15182-4:2007 (E) 4 1 Scope In addition to the requirements given in EN 15182-1, this document applies to hand-held high pressure branchpipes (nozzles) PN 40 with a maximum flow rate of 200 l/min at a reference pressure of 6 bar (0,6 MPa). It deals with: safety requirements; performance requirements; test methods; classification and designation; operating instructions; marking and maintenance. This part of this European Standard applies to branchpipes as defined in Annex A of EN 15182-1:2007. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 15182-1:2007, Hand-held branchpipes for fire service use - Part 1: Common requirements 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 15182-1:2007 and the following apply. 3.1 high pressure branchpipe branchpipe including a shut-off device and a variable pattern corresponding to the following definitions NOTE Branchpipe is defined in 3.1 of EN 15182-1:2007. 3.1.1 high pressure branchpipe – type 1 high pressure branchpipe with variable pattern at variable flow NOTE Changing pattern changes the flow. 3.1.2 high pressure branchpipe – type 2 high pressure branchpipe with variable pattern at constant flow NOTE Changing pattern does not change the flow.
EN 15182-4:2007 (E) 5 3.1.3 high pressure branchpipe – type 3 high pressure branchpipe with variable pattern at selectable, constant flow NOTE Changing pattern does not change the flow. 3.1.4 high pressure branchpipe – type 4 (automatic branchpipe) high pressure branchpipe with constant pressure NOTE Changing pattern does not change the flow. 3.1.4.1 high pressure branchpipe – type 4.1 high pressure branchpipe with variable pattern at constant pressure 3.1.4.2 high pressure branchpipe – type 4.2 high pressure branchpipe with variable pattern and selectable flow at constant pressure 3.2 jet
3.2.1 narrow spray jet intermediate position between the straight jet and the wide spray jet providing throw as well as protection 3.2.2 wide spray jet jet solely providing protection for the operator(s) 3.3 haptical device single mechanical device engaging detents 4 Requirements 4.1 General The branchpipes, covered by this standard, shall comply with EN 15182-1. 4.2 Mechanical characteristics 4.2.1 Dimensions and mass The branchpipes (without inlet coupling) shall not exceed the dimensions and masses specified in Table 1.
EN 15182-4:2007 (E) 6 Tabl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.