SIST EN 15182-3:2007

Hand-held branchpipes for fire service use - Part 3: Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16

In addition to the requirements given in EN 15182-1, this part of this European Standard applies to hand-held branchpipes with smooth bore jet and/or one fixed spray jet angle branchpipes PN 16, with a maximum flow rate of
1 000 l/min at a reference pressure of 6 bar (0,6 MPa). It deals with:
   safety requirements;
   performance requirements;
   test methods;
   classification and designation;
   information for use;
   marking and maintenance.
This part of this European Standard applies to branchpipes as defined in Annex A of EN 15182-1:2007.
NOTE 1   These branchpipes offer no or inadequate protection for firefighters when the spray angle is less than 30 ° and therefore, should not be used in high risk fire fighting situations such as internal attack.
NOTE 2   These branchpipes should not be used when fighting fires in or near electrical installations when the spray angle is less than 30 ° without written authorisation from the manufacturer in the manual. This authorisation from the manufacturer should include safety distances.

Strahlrohre für die Brandbekämpfung - Teil 3: Strahrohre mit Vollstrahl und/oder einem unveränderlichen Sprühstrahlwinkel PN 16

Zusätzlich zu den in prEN 15182-1 angegebenen Anforderungen gilt der vorliegende Teil dieser Europäischen Norm für Strahlrohre mit Vollstrahl und/oder einem unveränderlichen Sprühstrahlwinkel PN 16 mit einer maximalen Durchflussmenge von 1000 l/min bei einem Referenzdruck von 6 bar (0,6 MPa). Behandelt werden:
-   Sicherheitsanforderungen;
-   Anforderungen an die Funktion;
-               Prüfverfahren;
-   Klassifizierung und Bezeichnung;
-   Betriebsanleitung;
-   Kennzeichnung und Instandhaltung.
Der vorliegende Teil dieser Europäischen Norm gilt für Strahlrohre nach EN 15182-1, Anhang A.
ANMERKUNG 1   Da diese Strahlrohre keinen oder nur unzureichenden Schutz für das Feuerwehrpersonal bieten, wenn der Sprühwinkel weniger als 30 ° beträgt, sollten sie nicht in Brandbekämpfungs-Situationen mit hohem Risiko eingesetzt werden, wie z. B. Brandbekämpfung im Gebäudeinneren.
ANMERKUNG 2   Diese Strahlrohre sollten nicht für die Brandbekämpfung in oder an elektrischen Anlagen eingesetzt werden, wenn der Sprühwinkel weniger als 30 ° beträgt, sofern dies vom Hersteller nicht schriftlich im Handbuch autorisiert wurde. Diese Autorisierung des Herstellers sollte Mindestabstände einschließen.

Lances a main destinées aux services d`incendie et de secours - Partie 3: Lances a jet plein et/ou une diffusion a angle fixe PN 16

Gasilski ročniki - 3. del: Ročniki PN 16 s polnim curkom in/ali z razpršenim curkom pod določenim fiksnim kotom

General Information

• Status: Withdrawn
• Publication Date: 03-Jul-2007
• Withdrawal Date: 19-Nov-2009
• ICS: 13.220.10 - Fire-fighting
• Technical Committee: POZ - Požarna varnost
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 20-Nov-2009
• Due Date: 13-Dec-2009
• Completion Date: 20-Nov-2009
• Ref Project: EN 15182-3:2007 - Hand-held branchpipes for fire service use - Part 3: Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16

Relations

• Consolidated By: SIST EN 15182-3:2007+A1:2010 - Hand-held branchpipes for fire service use - Part 3: Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16
• Effective Date: 18-Jan-2023
• Consolidated By: SIST EN 15182-3:2007+A1:2010 - Hand-held branchpipes for fire service use - Part 3: Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16
• Effective Date: 19-Jan-2023
• Consolidated By: SIST EN 15182-3:2007+A1:2010 - Hand-held branchpipes for fire service use - Part 3: Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16
• Effective Date: 01-Jan-2010

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Hand-held branchpipes for fire service use - Part 3: Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16Lances a main destinées aux services d`incendie et de secours - Partie 3: Lances a jet plein et/ou une diffusion a angle fixe PN 16Strahlrohre für die Brandbekämpfung - Teil 3: Strahrohre mit Vollstrahl und/oder einem unveränderlichen Sprühstrahlwinkel PN 16Ta slovenski standard je istoveten z:EN 15182-3:2007SIST EN 15182-3:2007en;fr;de13.220.10Gašenje požaraFire-fightingICS:SLOVENSKI
STANDARDSIST EN 15182-3:200701-julij-2007







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15182-3February 2007ICS 13.220.10 English VersionHand-held branchpipes for fire service use - Part 3: Smooth borejet and/or one fixed spray jet angle branchpipes PN 16Lances à main destinées aux services d`incendie et desecours - Partie 3: Lances à jet plein et/ou une diffusion àangle fixe PN 16Strahlrohre für die Brandbekämpfung - Teil 3: Strahlrohremit Vollstrahl und/oder einem unveränderlichenSprühstrahlwinkel PN 16This European Standard was approved by CEN on 23 December 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15182-3:2007: E



EN 15182-3:2007 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Requirements.4 4.1 General.4 4.2 Mechanical characteristics.4 4.3 Hydraulic characteristics.5 4.4 Leak-tightness.6 4.5 Hydrostatic requirements.7 5 Testing and proofs.7 5.1 General.7 5.2 Spray angle measurement.7 5.3 Flow and throw test.7 5.4 Tightness test.8 5.5 Hydrostatic test.8



EN 15182-3:2007 (E) 3 Foreword This European Standard (EN 15182-3:2007) has been prepared by Technical Committee CEN/TC 192 “Fire service equipment”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2007, and conflicting national standards shall be withdrawn at the latest by August 2007. EN 15182 consists of the following parts, under the general title Hand-held branchpipes for fire service use:  Part 1: Common requirements;  Part 2: Combination branchpipes PN 16;  Part 3: Smooth bore jet and/or one fixed spray jet angle branchpipes PN 16;  Part 4: High pressure branchpipes PN 40. According to the CEN/CENELEC Internal Regulations, the national standards organ
...