SIST EN 60154-1:2016

Flanges for waveguides - Part 1: General requirements (IEC 60154-1:2016)

This part of IEC 60154 specifies the dimensions of waveguide flanges for use in electronic
equipment.
It covers requirements for flanges drilled before or after mounting on waveguides. It should be
noted that for optimum electrical performance, post-drilling of the alignment holes after
mounting is recommended.
The aim of this standard is to specify for waveguide flanges the mechanical requirements
necessary to ensure compatibility and, as far as practicable, interchangeability as well as to
ensure adequate electrical performance.

Flansche für Hohlleiter - Teil 1: Allgemeine Anforderungen (IEC 60154-1:2016)

Brides pour guides d'ondes - Partie 1: Prescriptions générales (IEC 60154-1:2016)

L'IEC 60154-1:2016 spécifie les dimensions des brides pour guides d'ondes utilisés dans les équipements électroniques. Elle couvre les exigences applicables aux brides percées avant ou après montage sur les guides d'ondes. Il convient de noter que, pour garantir des performances électriques optimales, il est recommandé de percer les trous d'alignement après le montage. La présente norme a pour but de spécifier les exigences mécaniques applicables aux brides de guides d'ondes qui sont nécessaires pour assurer la compatibilité et, autant que possible, l'interchangeabilité, mais aussi pour assurer des performances électriques suffisantes.

Prirobnice za valovode - 1. del: Splošne zahteve (IEC 60154-1:2016)

Ta del standarda IEC 60154 določa mere prirobnic za valovode, ki se uporabljajo v elektronski opremi.
Zajema zahteve za prirobnice, izvrtane pred ali po namestitvi na valovode. Opozoriti je treba, da je za optimalno električno zmogljivost priporočljivo vrtanje poravnalnih odprtin po namestitvi.
Cilj tega standarda je določiti mehanske zahteve, potrebne za zagotovitev združljivosti in, v največji možni meri, medsebojne zamenljivosti ter ustrezne električne zmogljivosti za prirobnice valovodov.

General Information

• Status: Published
• Publication Date: 07-Sep-2016
• ICS: 33.120.10 - Coaxial cables. Waveguides
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 07-Sep-2016
• Due Date: 12-Nov-2016
• Completion Date: 08-Sep-2016
• Ref Project: EN 60154-1:2016 - Flanges for waveguides - Part 1: General requirements

Relations

• Revised: SIST EN 60154-1:1998 - Flanges for waveguides -- Part 1: General requirements
• Effective Date: 27-Jan-2015
• Revised: SIST EN 60154-1:1998/A1:1998 - Flanges for waveguides -- Part 1: General requirements
• Effective Date: 27-Jan-2015
• Replaces: SIST EN 60154-1:1998 - Flanges for waveguides -- Part 1: General requirements
• Effective Date: 06-Sep-2016
• Replaces: SIST EN 60154-1:1998/A1:1998 - Flanges for waveguides -- Part 1: General requirements
• Effective Date: 06-Sep-2016
• Replaces: SIST EN 60154-1:1998 - Flanges for waveguides -- Part 1: General requirements
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60154-1:2016
01-november-2016
1DGRPHãþD
SIST EN 60154-1:1998
SIST EN 60154-1:1998/A1:1998
Prirobnice za valovode - 1. del: Splošne zahteve (IEC 60154-1:2016)
Flanges for waveguides - Part 1: General requirements (IEC 60154-1:2016)
Flansche für Hohlleiter - Teil 1: Allgemeine Anforderungen (IEC 60154-1:2016)
Brides pour guides d'ondes - Partie 1: Prescriptions générales (IEC 60154-1:2016)
Ta slovenski standard je istoveten z: EN 60154-1:2016
ICS:
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
SIST EN 60154-1:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60154-1:2016

---------------------- Page: 2 ----------------------

SIST EN 60154-1:2016


EUROPEAN STANDARD EN 60154-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2016
ICS 33.120.10 Supersedes EN 60154-1:1994
English Version
Flanges for waveguides -
Part 1: General requirements
(IEC 60154-1:2016)
Brides pour guides d'ondes -  Flansche für Hohlleiter -
Partie 1: Exigences générales Teil 1: Allgemeine Anforderungen
(IEC 60154-1:2016) (IEC 60154-1:2016)
This European Standard was approved by CENELEC on 2016-06-22. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60154-1:2016 E

---------------------- Page: 3 ----------------------

SIST EN 60154-1:2016
EN 60154-1:2016
European foreword
The text of document 46F/304/CDV, future edition 3 of IEC 60154-1, prepared by SC 46F "RF and
microwave passive components", of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 60154-1:2016.
The following dates are fixed:
• latest date by which the document has to be implemented at (dop) 2017-03-22
national level by publication of an identical national
standard or by endorsement
(dow) 2019-06-22
• latest date by which the national standards conflicting with
the document have to be withdrawn

This document supersedes EN 60154-1:1994.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60154-1:2016 was approved by CENELEC as a European
Standard without any modification.
2

---------------------- Page: 4 ----------------------

SIST EN 60154-1:2016
EN 60154-1:2016
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60050 series International Electrotechnical - -
Vocabulary (IEV)
IEC 60068 series Environmental testing EN 60068 series
IEC 60153 series Hollow metallic waveguides EN 60153 series

3

---------------------- Page: 5 ----------------------

SIST EN 60154-1:2016

---------------------- Page: 6 ----------------------

SIST EN 60154-1:2016



IEC 60154-1

®


Edition 3.0 2016-05




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Flanges for waveguides –

Part 1: General requirements




Brides pour guides d'ondes –

Partie 1: Exigences générales
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.120.10 ISBN 978-2-8322-3381-8



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60154-1:2016
– 2 – IEC 60154-1:2016 © IEC 2016
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references. 6
3 Terms and definitions . 6
4 General . 6
4.1 Flange designation . 6
4.2 Standard atmospheric conditions for testing . 7
4.3 Visual inspection . 7
5 Mechanical requirements . 7
5.1 General requirements both for mounted and unmounted flanges . 7
5.1.1 Holes . 7
5.1.2 Shank diameter of bolts used for alignment . 7
5.1.3 Relation between shank or alignment pin and alignment hole diameters . 8
5.1.4 Overall dimensions and thickness of flanges . 8
5.1.5 Surface roughness of contact area of contact flanges . 9
5.1.6 Flatness of contact area . 9
5.1.7 Perpendicularity of the axis of the holes . 9
5.1.8 General requirements for mounted flanges (assemblies) . 9
5.2 Additional requirements for unmounted flanges . 9
5.2.1 General . 9
5.2.2 Shape of aperture . 9
5.2.3 Positioning of the holes . 10
5.2.4 Ordering information . 10

Table 1 – Shank diameters . 8

---------------------- Page: 8 ----------------------

SIST EN 60154-1:2016
IEC 60154-1:2016 © IEC 2016 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FLANGES FOR WAVEGUIDES –

Part 1: General requirements

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All
...