SIST EN ISO 10893-9:2011
(Main)Non-destructive testing of steel tubes - Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the manufacture of welded steel tubes (ISO 10893-9:2011)
Non-destructive testing of steel tubes - Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the manufacture of welded steel tubes (ISO 10893-9:2011)
This part of ISO 10893 specifies requirements for the automated ultrasonic testing of strip/plate used in the manufacture of welded tubes for the detection of laminar imperfections carried out in the pipe mill before or during pipe production.
Zerstörungsfreie Prüfung von Stahlrohren - Teil 9: Automatisierte Ultraschallprüfung von Band/Blech, das für die Herstellung geschweißter Stahlrohre eingesetzt wird, zum Nachweis von Dopplungen (ISO 10893-9:2011)
Dieser Teil der ISO 10893 legt die Anforderungen an die automatische Ultraschallprüfung zum Nachweis von
Dopplungen in Band/Blech, das für die Herstellung geschweißter Rohre eingesetzt wird, fest. Die Prüfung wird
im Rohrwerk vor oder während der Rohrfertigung durchgeführt.
ANMERKUNG 1 Für geschweißte Rohre steht zum Nachweis von Dopplungen eine alternative Ultraschall-Prüfnorm zur
Verfügung, die nach Wahl des Herstellers angewendet werden darf, indem das Rohr nach dem Schweißen einer
Ultraschallprüfung nach ISO 10893-8 unterzogen wird.
ANMERKUNG 2 Nach Vereinbarung zwischen Hersteller und Besteller dürfen die Anforderungen dieses Teils der
ISO 10893 auf fertige unterpulvergeschweißte (SAW-)Rohre angewendet werden.
Dieses Dokument kann auch für die Prüfung von Bändern/Blechen, die für die Fertigung von Hohlprofilen mit
kreisförmigem Querschnitt zum Einsatz kommen, angewendet werden.
Essais non destructifs des tubes en acier - Partie 9: Contrôle automatisé par ultrasons pour la détection des dédoublures dans les bandes/tôles fortes utilisées pour la fabrication des tubes en acier soudés (ISO 10893-9:2011)
L'ISO 10893-9:2011 spécifie les exigences relatives au contrôle automatisé par ultrasons des bandes/tôles fortes utilisées pour la fabrication des tubes en acier soudés, pour la détection des dédoublures réalisée dans la tuberie avant ou pendant la production des tubes.
L'ISO 10893-9:2011 est également applicable au contrôle des bandes/tôles fortes utilisées pour la fabrication de profils creux circulaires.
Neporušitveno preskušanje jeklenih cevi - 9. del: Ugotavljanje laminarnih napak trakov/pločevine, ki se uporabljajo za izdelavo varjenih jeklenih cevi, z avtomatsko ultrazvočno preiskavo (ISO 10893-9:2011)
Ta del ISO 10893 določa zahteve za ugotavljanje laminarnih napak trakov/pločevine, ki se uporabljajo za izdelavo varjenih jeklenih cevi, z avtomatsko ultrazvočno preiskavo, ki se izvaja v valjarni cevi pred ali med proizvodnjo cevi.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10893-9:2011
01-november-2011
1DGRPHãþD
SIST EN 10246-15:2000
1HSRUXãLWYHQRSUHVNXãDQMHMHNOHQLKFHYL GHO 8JRWDYOMDQMHODPLQDUQLKQDSDN
WUDNRYSORþHYLQHNLVHXSRUDEOMDMR]DL]GHODYRYDUMHQLKMHNOHQLKFHYL]DYWRPDWVNR
XOWUD]YRþQRSUHLVNDYR ,62
Non-destructive testing of steel tubes - Part 9: Automated ultrasonic testing for the
detection of laminar imperfections in strip/plate used for the manufacture of welded steel
tubes (ISO 10893-9:2011)
Zerstörungsfreie Prüfung von Stahlrohren - Teil 9: Automatisierte Ultraschallprüfung von
Band/Blech, das für die Herstellung geschweißter Stahlrohre eingesetzt wird, zum
Nachweis von Dopplungen (ISO 10893-9:2011)
Essais non destructifs des tubes en acier - Partie 9: Contrôle automatisé par ultrasons
pour la détection des dédoublures dans les bandes/tôles fortes utilisées pour la
fabrication des tubes en acier soudés (ISO 10893-9:2011)
Ta slovenski standard je istoveten z: EN ISO 10893-9:2011
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.040.20 Neporušitveno preskušanje Non-destructive testing of
kovin metals
SIST EN ISO 10893-9:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10893-9:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 10893-9:2011
EUROPEAN STANDARD
EN ISO 10893-9
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 23.040.10; 77.040.20; 77.140.75 Supersedes EN 10246-15:2000
English Version
Non-destructive testing of steel tubes - Part 9: Automated
ultrasonic testing for the detection of laminar imperfections in
strip/plate used for the manufacture of welded steel tubes (ISO
10893-9:2011)
Essais non destructifs des tubes en acier - Partie 9: Zerstörungsfreie Prüfung von Stahlrohren - Teil 9:
Contrôle automatisé par ultrasons pour la détection des Automatisierte Ultraschallprüfung von Band/Blech, das für
dédoublures dans les bandes/tôles fortes utilisées pour la die Herstellung geschweißter Stahlrohre eingesetzt wird,
fabrication des tubes en acier soudés (ISO 10893-9:2011) zum Nachweis von Dopplungen (ISO 10893-9:2011)
This European Standard was approved by CEN on 10 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10893-9:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10893-9:2011
EN ISO 10893-9:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10893-9:2011
EN ISO 10893-9:2011 (E)
Foreword
This document (EN ISO 10893-9:2011) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the secretariat
of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10246-15:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10893-9:2011 has been approved by CEN as a EN ISO 10893-9:2011 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10893-9:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 10893-9:2011
INTERNATIONAL ISO
STANDARD 10893-9
First edition
2011-04-01
Non-destructive testing of steel tubes —
Part 9:
Automated ultrasonic testing for
the detection of laminar imperfections
in strip/plate used for the manufacture
of welded steel tubes
Essais non destructifs des tubes en acier —
Partie 9: Contrôle automatisé par ultrasons pour la détection
des dédoublures dans les bandes/tôles fortes utilisées
pour la fabrication des tubes en acier soudés
Reference number
ISO 10893-9:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 10893-9:2011
ISO 10893-9:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10893-9:2011
ISO 10893-9:2011(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 General requirements .2
5 Test method .2
6 Reference sample.4
6.1 General .4
6.2 Dimensions of reference standards .4
6.3 Verification of reference standards.4
7 Equipment calibration and checking.5
8 Acceptance .6
9 Test report.7
Annex A (normative) Procedure for the determination of the size of laminar imperfections
by manual ultrasonic testing.8
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10893-9:2011
ISO 10893-9:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10893-9 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 19, Technical
delivery conditions for steel tubes for pressure purposes.
This first edition cancels and replaces ISO 12094:1994, which has been technically revised.
ISO 10893 consists of the following parts, under the general title Non-destructive testing of steel tubes:
⎯ Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel
tubes for the verification of leaktightness
⎯ Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel
tubes for the detection of imperfections
⎯ Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged arc-
welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections
⎯ Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface
imperfections
⎯ Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of
surface imperfections
⎯ Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections
⎯ Part 7: Digital radiographic testing of the weld seam of welded steel tubes for the detection of
imperfections
⎯ Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar
imperfections
⎯ Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the
manufacture of welded steel tubes
⎯ Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged
arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 10893-9:2011
ISO 10893-9:2011(E)
⎯ Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of
longitudinal and/or transverse imperfections
⎯ Part 12: Automated full peripheral ultrasonic thickness testing of seamless and welded (except
submerged arc-welded) steel tubes
© ISO 2011 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 10893-9:2011
---------------------- Page: 12 ----------------------
SIST EN ISO 10893-9:2011
INTERNATIONAL STANDARD ISO 10893-9:2011(E)
Non-destructive testing of steel tubes —
Part 9:
Automated ultrasonic testing for the detection of laminar
imperfections in strip/plate used for the manufacture of welded
steel tubes
1 Scope
This part of ISO 10893 specifies requirements for the automated ultrasonic testing of strip/plate used in the
manufacture of welded tubes for the detection of laminar imperfections carried out in the pipe mill before or
during pipe production.
NOTE 1 For welded tubes, an alternative ultrasonic testing specification for the detection of laminar imperfections is
available, which can be applied, at the discretion of the manufacturer, by ultrasonic testing of the tubes subsequent to
seam welding according to ISO 10893-8.
NOTE 2 By agreement between the purchaser and manufacturer, the requirements of this part of ISO 10893 can be
applied on strips/plates of SAW tubes in the pipe form after seam welding.
This part of ISO 10893 can also be applicable to the testing of strips/plates used in the manufacture of circular
hollow sections.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 5577, Non-destructive testing — Ultrasonic inspection — Vocabulary
ISO 9712, Non-destructive testing — Qualification and certification of personnel
ISO 11484, Steel products — Employer's qualification system for non-destructive testing (NDT) personnel
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5577 and ISO 11484 and the
following apply.
3.1
reference standard
standard for the calibration of non-destructive testing equipment (e.g. drill holes, notches, recesses)
3.2
reference sample
sample (e.g. segment of plate/strip) containing the reference standard(s)
3.3
tube
hollow long product open at both ends, of any cross-sectional shape
© ISO 2011 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 10893-9:2011
ISO 10893-9:2011(E)
3.4
seamless tube
tube made by piercing a solid product to obtain a tube hollow, which is further processed, either hot or cold,
into its final dimensions
3.5
welded tube
tube made by forming a hollow profile from a flat product and welding adjacent edges together, and which
after welding can be further processed, either hot or cold, into its final dimensions
3.6
manufacturer
organization that manufactures products in accordance with the relevant standard(s) and declares the
compliance of the delivered products with all applicable provisions of the relevant standard(s)
3.7
agreement
contractual arrangement between the manufacturer and purchaser at the time of enquiry and order
3.8
laminar imperfection
imperfection located in the wall thickness and generally parallel to the pipe surfaces
NOTE Its extension can be calculated by measuring its outlined area on the external surface.
4 General requirements
4.1 An ultrasonic test of th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.