SIST EN IEC 62382:2024

Control systems in the process industry - Electrical and instrumentation loop check (IEC 62382:2024)

IEC 62382:2024 defines procedures and specifications for loop check, which comprises the activities between the completion of the loop construction (including installation and point-to-point checks) and the beginning of cold commissioning. This document is applicable for the construction of new plants and for expansion or retrofits (i.e. revamping) of electrical and instrument (E&I) installations in existing plants (including PLC, DCS, panel-mounted and field instrumentation). It does not include a detailed checkout of power distribution systems, except as they relate to the loops being checked (i.e. a motor starter or a power supply to a four-wire transmitter). Loop checks can be performed throughout the lifecycle of the plant. This document is also applicable when loop checks are performed after commissioning. This document describes what is intended to be tested but not how the test is performed, due to the wide range of technologies and equipment available.
The intent of this document is to provide a means for all parties, including the owner, the installer and the vendor, to clearly establish and agree on the scope of activities and responsibilities involved in performing these tests in order to achieve a timely delivery and acceptance of the automation system. The activities described in this document can be taken as a guideline and adapted to the specific requirements of the process, plant or equipment.
This edition includes the following significant technical changes with respect to the previous edition:
a) general re-organization of the content of the previous edition, moving informative content to the annexes;
b) replacing the forms based on I/O type in IEC 62382:2012, Annex A to Annex E with an example of a generic loop check form;
c) providing additional references to other applicable standards.

Leittechnische Systeme in der verfahrenstechnischen Industrie - PLT-Stellenprüfung (IEC 62382:2024)

Systèmes de commande pour les procédés industriels - Contrôle de boucle des circuits électriques et des appareillages (IEC 62382:2024)

IEC 62382:2024 définit les procédures et les spécifications relatives à un contrôle de boucle, qui se compose des activités comprises entre l’achèvement de la construction de la boucle (installation et contrôles de point à point) et le début de la mise en service à froid. Il s'applique à la construction de nouvelles usines, ainsi qu'à l'extension ou à la modernisation des installations de systèmes électriques et instruments de fonctionnement (E&I - electrical & instrument) dans les usines existantes (PLC - programmable logic controller, DCS - distributed control system, appareils montés sur panneau et appareils de terrain compris). Elle ne comprend pas de vérification détaillée des réseaux de distribution d'électricité, hormis dans la mesure où ils sont rattachés aux boucles faisant l'objet du contrôle (c'est-à-dire dans le cas d'un démarreur de moteur ou d'une alimentation électrique pour un transmetteur à quatre fils). Les contrôles de boucle peuvent être effectués tout au long du cycle de vie de l’usine. Le présent document s'applique également aux contrôles de boucle effectués après la mise en service. Le présent document décrit ce qui est destiné à être soumis à l’essai et non la méthode d’essai en raison de la large plage de technologies et d’équipements disponibles.
Le présent document a pour objet de permettre à toutes les parties, y compris le maître d’ouvrage, l’acheteur et l’installateur, de définir clairement et de convenir de l’étendue des activités et des responsabilités liées à l'exécution de ces essais, afin de finaliser la livraison et l'acceptation des systèmes d’automatisation dans les délais prévus. Les activités décrites dans le présent document peuvent être considérées comme des lignes directrices et être adaptées aux exigences spécifiques du processus, de l'usine ou de l'équipement.
Cette troisième édition annule et remplace la deuxième édition parue en 2012. Cette édition constitue une révision technique.
Les principales modifications par rapport à l'édition précédente sont les suivantes:
a) réorganisation générale du contenu de l’édition précédente, en déplaçant le contenu informatif vers les annexes;
b) remplacement, dans les Annexes A à E de l’IEC 62382, des formulaires fondés sur le type d’E/S par un exemple de formulaire générique de contrôle de boucle;
c) ajout de références supplémentaires à d’autres normes applicables.

Krmilni sistemi v procesni industriji - Preverjanje električnih in merilnih zank (IEC 62382:2024)

General Information

• Status: Published
• Public Enquiry End Date: 22-Oct-2023
• Publication Date: 12-Nov-2024
• ICS: 25.040.40 - Industrial process measurement and control
• Technical Committee: MOV - Measuring equipment for electromagnetic quantities
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 30-Sep-2024
• Due Date: 05-Dec-2024
• Completion Date: 13-Nov-2024
• Ref Project: EN IEC 62382:2024 - Control systems in the process industry - Electrical and instrumentation loop check

Relations

• Revises: SIST EN 62382:2013 - Control systems in the process industry - Electrical and instrumentation loop check (IEC 62382:2012)
• Effective Date: 01-Mar-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2024
Krmilni sistemi v procesni industriji - Preverjanje električnih in merilnih zank (IEC
62382:2024)
Control systems in the process industry - Electrical and instrumentation loop check (IEC
62382:2024)
Leittechnische Systeme in der verfahrenstechnischen Industrie - PLT-Stellenprüfung
(IEC 62382:2024)
Systèmes de commande pour les procédés industriels - Contrôle de boucle des circuits
électriques et des appareillages (IEC 62382:2024)
Ta slovenski standard je istoveten z: EN IEC 62382:2024
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 62382

NORME EUROPÉENNE
EUROPÄISCHE NORM September 2024
ICS 25.040.40 Supersedes EN 62382:2013
English Version
Control systems in the process industry - Electrical and
instrumentation loop check
(IEC 62382:2024)
Systèmes de commande dans l'industrie de transformation Leittechnische Systeme in der verfahrenstechnischen
- Contrôle de boucle des circuits électriques et des Industrie - PLT-Stellenprüfung
appareillages (IEC 62382:2024)
(IEC 62382:2024)
This European Standard was approved by CENELEC on 2024-09-18. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62382:2024 E
European foreword
The text of document 65E/1082/FDIS, future edition 3 of IEC 62382, prepared by SC 65E "Devices
and integration in enterprise systems" of IEC/TC 65 "Industrial-process measurement, control and
automation" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-06-18
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-09-18
document have to be withdrawn
This document supersedes EN 62382:2013 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62382:2024 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 61131 (series) NOTE Approved as EN IEC 61131 (series)
IEC 61511 (series) NOTE Approved as EN 61511 (series)
IEC 61511-1:2016 NOTE Approved as EN 61511-1:2017 (not modified)
IEC 62443 (series) NOTE Approved as EN IEC 62443 (series)
IEC 62708 NOTE Approved as EN 62708
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 62381 - Automation systems in the process EN IEC 62381 -
industry - Factory acceptance test (FAT),
site acceptance test (SAT), and site
integration test (SIT)
IEC 62382 ®
Edition 3.0 2024-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Control systems in the process industry – Electrical and instrumentation loop

check
Systèmes de commande dans l’industrie de transformation – Contrôle de boucle

des circuits électriques et des appareillages

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.040.40  ISBN 978-2-8322-9531-1

– 2 – IEC 62382:2024 © IEC 2024
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
1.1 General applicability . 7
1.2 Exclusions . 7
1.2.1 Prior and post activities . 7
1.2.2 Regulated industries . 7
1.2.3 Safety instrumented systems . 7
1.2.4 Manufacturing execution systems . 7
1.2.5 Advanced process control . 7
1.2.6 Security for industrial automation and control systems . 7
1.2.7 User-specific procedures and requirements . 8
2 Normative references . 8
3 Terms, definitions and abbreviated terms . 8
3.1 Terms and definitions . 8
3.2 Abbreviated terms . 11
4 Loop check schedule . 12
5 Loop check content . 12
5.1 Included activities . 12
5.1.1 General . 12
5.1.2 Loop check phases . 13
5.1.3 Deficiencies . 13
5.2 Excluded activities . 13
6 Loop check procedure . 14
6.1 Loop check planning . 14
6.2 Performance of loop check . 15
6.2.1 Documentation check . 15
6.2.2 Visual inspection . 15
6.2.3 Functional check prerequisites . 15
6.2.4 Functional check. 16
6.3 Additional tests – Quality and safety relevant loops . 16
6.4 Partial loop checks . 16
6.5 After completion of loop checks . 16
7 Documentation of performed loop checks . 16
7.1 Documentation . 16
7.2 Loop check results . 17
8 Quality assurance . 17
9 Safety aspects . 17
10 Loop checks post commissioning . 17
Annex A (informative) Examples of loop tests . 19
A.1 General . 19
A.2 Loop check prerequisites . 19
A.3 Measurements . 19
A.4 Actuators and valves . 20
A.5 Motor loops . 20
A.6 Alarms . 21

IEC 62382:2024 © IEC 2024 – 3 –
A.7 Diagnostics . 21
A.8 Standard loops . 21
A.9 Non-standard loops . 21
A.9.1 Loops containing intelligent devices . 21
A.9.2 Loops containing devices with network and system security . 21
A.9.3 Special loops . 21
A.9.4 Interlocks . 22
A.9.5 Quality loops . 22
A.9.6 Safety loops . 22
A.9.7 Asset management system loops . 22
A.10 Loop infrastructure . 22
A.11 E&I general concepts . 23
Annex B (informative) Loop check form . 24
Bibliography . 27

Figure 1 – Project phases and E&I testing . 12
Figure B.1 – Loop check form – Page 1 . 25
Figure B.2 – Loop check form – Page 2 . 26

– 4 – IEC 62382:2024 © IEC 2024
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONTROL SYSTEMS IN THE PROCESS INDUSTRY –
ELECTRICAL AND INSTRUMEN
...