iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1948-3:1999

(Main)

Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs - Part 3: Identification and quantification

Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs - Part 3: Identification and quantification

The present Part of the Standard specifies the identification and quantificationprocedures of the sampled PCDDs/PCDFs. It is an integral part of the complete measurement procedure. The use of the other two parts of this Standard, EN 1948-1:1996 and EN 1948-2:1996, describing sampling and extraction and clean-up, respectively, is necessary for the determination of the PCDDs/PCDFs. This Stan- dard has been designed to measure PCDD/PCDF concentrations at about 0,1 ng I-TEQ/m cube in stationary source emissions.

Emissionen aus stationären Quellen - Bestimmung der Massenkonzentration von PCDDs/PCDFs - Teil 3: Identifizierung und Quantifizierung

Der vorliegende Teil der Norm das Identifizierungs- und Quantifizierungs- verfahren für die gesammelten PCDD/PCDF fest. Er ist integraler Bestandteil des vollständigen Messverfahrens. Die Anwendung der anderen beiden Teile dieserNorm EN 1948-1:1996 und EN 1948-2:1996, die die Probenahme bzw. die Extraktion und Reinigung beschreiben, ist notwendig für die Bestimmung der PCDD und PCDF. Diese Norm ist für die Messung von PCDD/PCDF-Emissionskonzentrationen von stationären Quellen im Bereich von 0,1 ng I-TEQ/m3 konzipiert.

Emissions de sources fixes - Détermination de la concentration massique en PCDDs/PCDFs - Partie 3: Identification et quantification

La présente partie de la N.E. spécifie des procédures d'identification et quan- tification pour les échantillons de PCDD/PCDF prélevés. Elle est partie intég- rante de la procédure complete de mesure. L'utilisation des deux autres parties de l'EN 1948-1:1996 et EN 1948-2:1996 décrivant d'une part le prélevement, d'autre part l'extraction et la purification est nécessaure pour la détermi- nation des PCDD et PCDF. Cette norme a été préparée pour mesurer des concentra- tions au niveau 0,1 ng I-TEQ/m cube dans les émissions de sources fixes

Emisije nepremičnih virov – Določevanje masne koncentracije PCDD/PCDF – 3. del: Identifikacija in kvantifikacija

General Information

Status
Withdrawn
Publication Date
31-Aug-1999
Withdrawal Date
30-Apr-2006
ICS
13.040.40 - Stationary source emissions
Technical Committee
KAZ - Air quality
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-May-2006
Due Date
01-May-2006
Completion Date
01-May-2006
Directive
89/369/EEC - Prevention of air pollution from new municipal waste incineration plants
89/429/EEC - Reduction of air pollution from existing municipal waste incineration plants
94/67/EC - Incineration of hazardous waste
Mandate
M/BC/CEN/91/12 - Standardization mandate for CEN concerning a standardized measurement method for dioxins and furans emissions in exhausted gas
Ref Project
EN 1948-3:1996 - Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs - Part 3: Identification and quantification

Relations

Replaced By
SIST EN 1948-3:2006 - Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 3: Identification and quantification of PCDDs/PCDFs
Effective Date
01-May-2006

Buy Standard

EN 1948-3:1999EN 1948-3:1999
PreviousNext
Standard
EN 1948-3:1999
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1948-3:1999
01-september-1999
(PLVLMHQHSUHPLþQLKYLURY±'RORþHYDQMHPDVQHNRQFHQWUDFLMH3&''3&')±
GHO,GHQWLILNDFLMDLQNYDQWLILNDFLMD
Stationary source emissions - Determination of the mass concentration of
PCDDs/PCDFs - Part 3: Identification and quantification
Emissionen aus stationären Quellen - Bestimmung der Massenkonzentration von
PCDDs/PCDFs - Teil 3: Identifizierung und Quantifizierung
Emissions de sources fixes - Détermination de la concentration massique en
PCDDs/PCDFs - Partie 3: Identification et quantification
Ta slovenski standard je istoveten z: EN 1948-3:1996
ICS:
13.040.40 (PLVLMHQHSUHPLþQLKYLURY Stationary source emissions
SIST EN 1948-3:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1948-3:1999

---------------------- Page: 2 ----------------------

SIST EN 1948-3:1999

---------------------- Page: 3 ----------------------

SIST EN 1948-3:1999

---------------------- Page: 4 ----------------------

SIST EN 1948-3:1999

---------------------- Page: 5 ----------------------

SIST EN 1948-3:1999

---------------------- Page: 6 ----------------------

SIST EN 1948-3:1999

---------------------- Page: 7 ----------------------

SIST EN 1948-3:1999

---------------------- Page: 8 ----------------------

SIST EN 1948-3:1999

---------------------- Page: 9 ----------------------

SIST EN 1948-3:1999

---------------------- Page: 10 ----------------------

SIST EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST ISO 10849:2023(Main)
Stationary source emissions - Determination of the mass concentration of nitrogen oxides in flue gas - Performance characteristics of automated measuring systems
ISO 10849:2022

This document specifies a method for the determination of nitrogen oxides (NOx) in flue gas of stationary sources and describes the fundamental structure and the key performance characteristics of automated measuring systems.
The method allows continuous monitoring with permanently installed measuring systems of NOx emissions.
This document describes extractive systems and in situ (non-extractive) systems in connection with a range of analysers that operate using, for example, the following principles:
— chemiluminescence (CL);
— infrared absorption (NDIR);
— Fourier transform infrared (FTIR) spectroscopy;
— ultraviolet absorption (NDUV);
— differential optical absorption spectroscopy (DOAS);
Other equivalent instrumental methods such as laser spectroscopic techniques can be used provided they meet the minimum performance requirements specified in this document. The measuring system can be validated with reference materials, in accordance with this document, or comparable methods.
Automated measuring system (AMS) based on the principles listed above has been used successfully in this application for the measuring ranges as shown in Annex F.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    47 pages
    English language
    sale 15% off
  • Draft
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST ISO 20181:2023(Main)
Stationary source emissions - Quality assurance of automated measuring systems
ISO 20181:2023

This document was prepared by the European Committee for Standardization (CEN) as EN 14181:2014 and was adopted, without modification.
This document specifies procedures for establishing quality assurance levels (QAL) for automated measuring systems (AMS) installed on industrial plants for the determination of the flue gas components and other flue gas parameters.
This document specifies:
— a procedure (QAL2) to calibrate the AMS and determine the variability of the measured values obtained by it, so as to demonstrate the suitability of the AMS for its application, following its installation;
— a procedure (QAL3) to maintain and demonstrate the required quality of the measurement results during the normal operation of an AMS, by checking that the zero and span characteristics are consistent with those determined during QAL1;
— a procedure for the annual surveillance tests (AST) of the AMS in order to evaluate (i) that it functions correctly and its performance remains valid and (ii) that its calibration function and variability remain as previously determined.
This document is designed to be used after the AMS has been certified in accordance with the series of documents EN 15267.

  • Standard
    80 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    74 pages
    English language
    sale 15% off
  • Draft
    80 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17255-4:2023(Main)
Stationary source emissions - Data acquisition and handling systems - Part 4: Specification of requirements for the installation and on-going quality assurance and quality control of data acquisition and handling systems
EN 17255-4:2023

This document specifies the requirements for the installation and on-going quality assurance and quality control of data acquisition and handling systems (DAHS). This includes requirements on
— installation (Clause 5)
— quality assurance and quality control during QAL2 (Clause 6)
— quality assurance and quality control during on-going operation (Clause 7)
— annual functional test (Clause 8)
This document supports the requirements of EN 14181 and legislation such as the IED, MCPD and E-PRTR. It does not preclude the use of additional features and functions provided the minimum requirements of this European Standard are met and that these features do not adversely affect data quality, clarity or access.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 17911:2023(Main)
Stationary source emissions - Guideline for the elaboration of standardized measurement methods - Recommendations for the structure and content
CEN/TR 17911:2023

This document supports the elaboration of standardized measurement methods for the determination of stationary source emissions by manual or automated measurement methods.
This document describes the basic elements of standardized measurement methods for the determination of stationary source emissions.
This document is supplemented by an electronic template providing a uniform structure and common elements and texts.
NOTE   Detailed information on the electronic template is given in Annex A.
This document is addressed to working groups of CEN/TC 264 dealing with stationary source emissions. It aims at facilitating in the working groups the elaboration and the harmonization of documents produced by CEN/TC 264. Such documents can be European standards (EN), European Technical Specifications (CEN/TS) or European Technical Reports (CEN/TR).

  • Technical report
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14884:2023(Main)
Stationary source emissions - Determination of total mercury - Automated measuring systems
EN 14884:2022

This European Standard specifies requirements for the calibration and validation (QAL2), the ongoing quality assurance during operation (QAL3) and the annual surveillance test (AST) of automated measuring systems (AMS) used for monitoring total mercury emissions from stationary sources to demonstrate compliance with an emission limit value (ELV). This document is derived from EN 14181 and is only applicable in conjunction with EN 14181.
This document is applicable by direct correlation with the standard reference method (SRM) described in EN 13211.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17656:2023(Main)
Stationary source emissions - Requirements on proficiency testing schemes for emission measurements
EN 17656:2022

This document specifies requirements on
—the competence of proficiency testing providers,
—the test facility characteristics, and
—the design, operation and evaluation of proficiency testing schemes by means of interlaboratory comparisons.
All these aspects are necessary in order to organise and conduct proficiency testing on industrial emissions that is ‘Fit for the Purposes’ declared in the scope of the proficiency testing.
Requirements on the competence of proficiency testing providers cover personnel, organisation, equipment and environment.
Requirements on the test facility characteristics cover measurement sections, measurements ports and working area for the participants.
Requirements on the proficiency testing schemes cover
—the design, including planning, preparations, homogeneity and stability of test atmospheres and statistical design,
—the operation, including handling and instruction of participants, and
—testing results evaluation, including statistical data.
This document supplements the requirements of EN ISO/IEC 17043.
This document supports the application of proficiency testing schemes for checking the performance of testing laboratories in the context of qualification, accreditation and related quality checks in relation to the application of standardized measurement methods such as standard reference methods (SRM) or alternative methods (AM).

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17628:2022(Main)
Fugitive and diffuse emissions of common concern to industry sectors - Standard method to determine diffuse emissions of volatile organic compounds into the atmosphere
EN 17628:2022

This document specifies the framework for determining emissions to the atmosphere of Volatile Organic Compounds (VOCs). It defines a system of methods to detect and/or identify and/or quantify VOC emissions from industrial sources. These methods include Optical Gas Imaging (OGI), Differential Absorption Lidar (DIAL), Solar Occultation Flux (SOF), Tracer Correlation (TC), and Reverse Dispersion Modelling (RDM). It specifies the methodologies for carrying out all the above, and also defines the performance requirements and capabilities of the direct monitoring methods, the requirements for the results and their measurement uncertainties.
This document specifically addresses, but is not restricted to, the petrochemicals, oil refining, and chemical industries receiving, processing, storing, and/or exporting of VOCs, and includes the emissions of VOCs from the natural gas processing/conditioning industry and the storage of natural gas and similar fuels.
This document addresses diffuse VOC emissions to atmosphere but excludes the emissions of VOCs into water and into solid materials such as soils. It is complementary to EN 15446 [9], which covers detection, localization of sources (individual leaks from equipment and piping), and quantification of fugitive VOC emissions within the scope of a Leak Detection and Repair Programme (LDAR).
This document has been validated for non-methane VOCs, but the methodologies are in principle applicable to methane and other gases.
This document defines methods to determine (detect, identify and/or quantify) VOC emissions during the periods of monitoring. It does not address the extrapolation of emissions to time periods beyond the monitoring period.

  • Standard
    101 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13725:2022(Main)
Stationary source emissions - Determination of odour concentration by dynamic olfactometry and odour emission rate
EN 13725:2022

This document specifies a method for the objective determination of the odour concentration of a gaseous sample using dynamic olfactometry with human assessors. The standard also specifies a method for the determination of the emission rate of odours from stationary sources, in particular:
-   point sources (conveyed or ducted emissions);
-   active area sources (e.g. biofilters);
-   passive sources.
The primary application of this standard is to provide a common basis for evaluation of odour emissions.
When this document is used for the determination of the odour concentration or the odour emission rate of stationary source emissions, the other relevant European Standards concerning stationary source emissions apply, in particular EN 15259 and EN 16911-1, especially when measurements have to be in compliance with the relevant European Directives concerning industrial air emissions.
Even so, the analysis/quantification step of the measurement method described in this document (i.e. the determination of the odour concentration of an odorous gas sample, without respect to the origin of the sample itself) can be fully applied in many cases not related with industrial emission sources (e.g. the measurement of the mass concentration at the detection threshold of pure odorous substances, the determination of effectiveness of deodorizing systems for indoor air). In those latter cases, the requirements in this document concerning the measurement planning and the sampling of stationary sources  can be ignored or adapted.
This document is applicable to the measurement of odour concentration of pure substances, defined odorant compounds and undefined mixtures of odorant volatiles in air or nitrogen, using dynamic olfactometry with a panel of human assessors being the sensor. The unit of measurement is the European odour unit per cubic metre: ouE/m3. The odour concentration is measured by determining the dilution factor required to reach the detection threshold. The odour concentration at the detection threshold is by definition 1 ouE/m3. The odour concentration is then expressed in terms of multiples of the detection threshold. The range of measurement is typically from 101 ouE/m3 to 107 ouE/m3 (including pre dilution).
The field of application of this document includes:
-   the measurement of the mass concentration at the detection threshold of pure odorous substances in g/m3;
-   the determination of the EROM value of odorants, in mol;
-   the measurement of the odour concentration of mixtures of odorants in ouE/m3;
-   the measurement of the emission rate of odorous emissions from point sources, active area sources and passive area sources, including pre dilution during sampling;
-   the sampling of odorous gases from emissions of high humidity and temperature (up to 200 °C);
-   the determination of effectiveness of end-of-pipe mitigation techniques used to reduce odour emissions.
The determination of odour emissions requires measurement of gas velocityto determine the gas volume flow rate.
The field of application of this document does not include:
-   the measurement of odours potentially released by particles of odorous solids or droplets of odorous fluids suspended in emissions;
-   the measuring strategy to be applied in case of variable emission rates;
-   the measurement of the relationship between odour stimulus and assessor response above detection threshold (perceived intensity);
-   measurement of hedonic tone (or (un)pleasantness) or assessment of annoyance potential;
-   direct measurement of odour exposure in ambient air. For this measurement purpose, field panel methods exist which are the subject of CEN standard EN 16841-1, Ambient Air - Determination of odour in ambient air by using field inspection - Grid method;
-   direct olfactometry, including field olfactometry;
-   static olfactometry;
-   measurement of odour recognition thresholds;
-   measurement of odour identification thresholds.
.....

  • Standard
    124 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    124 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17255-3:2022(Main)
Stationary source emissions - Data acquisition and handling systems - Part 3: Specification of requirements for the performance test of data acquisition and handling systems
EN 17255-3:2021

This document specifies the performance test of data acquisition and handling systems (DAHS). This includes specification of
— test procedures;
— description of laboratory test;
— requirements on the testing laboratory.
This document supports the requirements of EN 14181 and legislation such as the IED, MCPD and E PRTR. It does not preclude the use of additional features and functions provided the minimum requirements of this document are met and that these features do not adversely affect data quality, clarity or access.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 17638:2021(Main)
Stationary source emissions - Determination of the mass concentration of formaldehyde - Manual method
CEN/TS 17638:2021

This Technical Specification specifies a manual method for the determination of the concentration of formaldehyde in emissions from stationary sources. Waste gas samples are taken by absorption in water and subsequently analysed by spectrophotometry or HPLC. The method applies to waste gases in which the formaldehyde concentration is 2 mg⋅m–3 to 60 mg⋅m–3, on dry basis, at the reference conditions of 273 K and 101,3 kPa.

  • Technical specification
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day