SIST EN 1081:2019+A1:2020
(Main)Resilient, laminate and modular multilayer floor coverings - Determination of the electrical resistance
Resilient, laminate and modular multilayer floor coverings - Determination of the electrical resistance
This document specifies test methods for determining:
a) the vertical resistance,
b) the resistance to earth,
c) the surface resistance
of a resilient, laminate and modular multilayer floor covering after installation in test piece or after installation.
Elastische, Laminat- und modulare mehrschichtige Bodenbeläge - Bestimmung des elektrischen Widerstandes
[Not available]
Revêtements de sol résilients, stratifiés et multicouches modulaires - Détermination de la résistance électrique
Le présent document spécifie des méthodes d'essai visant à déterminer :
a) la résistance transversale,
b) la résistance à la terre,
c) la résistance superficielle
d'un revêtement de sol résilient, stratifié et multicouche modulaire, après la pose d'une éprouvette, ou une fois le revêtement de sol posé.
Netekstilne, laminirane (plastene) in večplastne talne obloge - Ugotavljanje električne upornosti
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1081:2019+A1:2020
01-december-2020
Netekstilne, laminirane (plastene) in večplastne talne obloge - Ugotavljanje
električne upornosti
Resilient, laminate and modular multilayer floor coverings - Determination of the
electrical resistance
Elastische, Laminat- und modulare mehrschichtige Bodenbeläge - Bestimmung des
elektrischen Widerstandes
Revêtements de sol résilients, stratifiés et multicouches modulaires - Détermination de la
résistance électrique
Ta slovenski standard je istoveten z: EN 1081:2018+A1:2020
ICS:
97.150 Talne obloge Floor coverings
SIST EN 1081:2019+A1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1081:2019+A1:2020
---------------------- Page: 2 ----------------------
SIST EN 1081:2019+A1:2020
EN 1081:2018+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2020
EUROPÄISCHE NORM
ICS 97.150 Supersedes EN 1081:2018
English Version
Resilient, laminate and modular multilayer floor coverings
- Determination of the electrical resistance
Revêtements de sol résilients, stratifiés et Elastische, Laminat- und modulare mehrschichtige
multicouches modulaires - Détermination de la Bodenbeläge - Bestimmung des elektrischen
résistance électrique Widerstandes
This European Standard was approved by CEN on 1 July 2018 and includes Amendment approved by CEN on 10 August 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1081:2018+A1:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1081:2019+A1:2020
EN 1081:2018+A1:2020 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Sampling . 5
5 Apparatus and reagents . 5
6 Method A — For vertical resistance, R1 . 7
7 Method B - For resistance to earth, R2 . 8
8 Method C for surface resistance, R3 . 9
9 Calculation and expression of results . 11
10 Test report . 11
2
---------------------- Page: 4 ----------------------
SIST EN 1081:2019+A1:2020
EN 1081:2018+A1:2020 (E)
European foreword
This document (EN 1081:2018+A1:2020) has been prepared by Technical Committee CEN/TC 134
“Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall
be withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1 approved by CEN on 10 August 2020.
This document supersedes !EN 1081:2018".
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 1081:2019+A1:2020
EN 1081:2018+A1:2020 (E)
1 Scope
This document specifies test methods for determining:
a) the vertical resistance,
b) the resistance to earth,
c) the surface resistance
of a resilient, laminate and modular multilayer floor covering after installation in test piece or after
installation.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 62631-3-1, Dielectric and resistive properties of solid insulating materials - Part 3-1: Determination of
resistive properties (DC methods) - Volume resistance and volume resistivity - General method
(IEC 62631-3-1)
ISO 48, Rubber, vulcanized or thermoplastic - Determination of hardness (hardness between 10 IRHD and
100 IRHD)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
vertical resistance R1
electrical resistance measured between a tripod electrode on the surface of a test piece and an electrode
attached to the underside of the test piece
Note 1 to entry: See Figure 1 for tripod electrode and see Figure 2 for testing of vertical resistance.
3.2
resistance to earth R2
electrical resistance measured between a loaded tripod electrode on the surface of a laid floor covering
and earth
3.3
surface resistance R3
electrical resistance measured between two tripod electrodes set up at a fixed distance of 100 mm apart
on a laid floor covering
Note 1 to entry: See Figure 4 for the electrical resistance measured between two tripod electrodes and see
Figure 3 for distance of 100 mm apart on a laid floor covering.
4
---------------------- Page: 6 ----------------------
SIST EN 1081:2019+A1:2020
EN 1081:2018+A1:2020 (E)
4 Sampling
For method A or when measurements are done in laboratory, take a representative sample from the
whole of the available material. In the case of rolls, take approximately a third of the test pieces from
the area close to the edges, the distance between the outer edge of the sample and the nearest edge of
the roll being between 50 mm and 100 mm.
5 Apparatus and reagents
5.1 Tripod electrode
The tripod electrode (Figure 1) shall be capable of comprising a triangular aluminium plate with an
insulating layer on the upper surface and three cylindrical feet of conductive rubber on the underside at
a distance of 180 mm apart.
The rubber feet shall have a hardness in accordance with ISO 48 of 50 IRHD to 70 IRHD, and the
3
electrical resistance of each rubber foot shall be less than 10 Ohm when t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.