SIST EN ISO 13850:2008
(Main)Safety of machinery - Emergency stop - Principles for design (ISO 13850:2006)
Safety of machinery - Emergency stop - Principles for design (ISO 13850:2006)
This International Standard specifies functional requirements and design principles for the emergency stop function on machinery, independent of the type of energy used to control the function. It is applicable to all machinery except for: - machines in which the provision of emergency stop would not lessen the risk; - hand-held portable machines and hand-guided machines.
Sicherheit von Maschinen - Not-Halt - Gestaltungsleitsätze (ISO 13850:2006)
Diese Norm legt funktionale Anforderungen und Gestaltungsleitsätze für Not-Halt unabhängig von der Art der verwendeten Energie für die Steuerfunktion fest.
Die Anforderungen dieser Norm gelten für alle Maschinen, mit Ausnahme von:
- Maschinen, bei denen ein Not-Halt das Risiko nicht verringern würde;
- von Hand tragbaren und handgeführten Maschinen.
Diese Norm behandelt nicht die Funktionen wie Umkehr und Begrenzen von Bewegungen, Abweisen, Abschirmen, Bremsen oder Unterbrechen, die Teil der Not-Halt-Funktion sein können.
Sécurité des machines - Arrêt d'urgence - Principes de conception (ISO 13850:2006)
L'ISO 13850:2006 spécifie les exigences fonctionnelles et les principes de conception des arrêts d'urgence, indépendamment du type d'énergie utilisée pour commander la fonction. Elle s'applique à toutes les machines, à l'exception des machines dans lesquelles la mise en oeuvre d'un arrêt d'urgence ne réduirait pas le risque, et des machines portatives tenues à la main et des machines guidées à la main. Elle ne traite pas des fonctions telles que l'inversion ou la limitation du mouvement, la déflexion, l'interposition d'un écran, le freinage, ou la déconnexion qui peuvent faire partie de la fonction arrêt d'urgence.
Varnost strojev - Zaustavitev v sili - Načela načrtovanja (ISO 13850:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13850:2008
01-oktober-2008
1DGRPHãþD
SIST EN ISO 13850:2007
9DUQRVWVWURMHY=DXVWDYLWHYYVLOL1DþHODQDþUWRYDQMD ,62
Safety of machinery - Emergency stop - Principles for design (ISO 13850:2006)
Sicherheit von Maschinen - Not-Halt - Gestaltungsleitsätze (ISO 13850:2006)
Sécurité des machines - Arrêt d'urgence - Principes de conception (ISO 13850:2006)
Ta slovenski standard je istoveten z: EN ISO 13850:2008
ICS:
13.110 Varnost strojev Safety of machinery
SIST EN ISO 13850:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13850:2008
---------------------- Page: 2 ----------------------
SIST EN ISO 13850:2008
EUROPEAN STANDARD
EN ISO 13850
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2008
ICS 13.110 Supersedes EN ISO 13850:2006
English Version
Safety of machinery - Emergency stop - Principles for design
(ISO 13850:2006)
Sécurité des machines - Arrêt d'urgence - Principes de Sicherheit von Maschinen - Not-Halt - Gestaltungsleitsätze
conception (ISO 13850:2006) (ISO 13850:2006)
This European Standard was approved by CEN on 25 May 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13850:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13850:2008
EN ISO 13850:2008 (E)
Contents Page
Foreword.3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC .4
Annex ZB (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC .5
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13850:2008
EN ISO 13850:2008 (E)
Foreword
The text of ISO 13850:2006 has been prepared by Technical Committee ISO/TC 199 “Safety of machinery” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 13850:2008 by
Technical Committee CEN/TC 114 “Safety of machinery” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2008, and conflicting national standards shall be withdrawn
at the latest by December 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13850:2006.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annexes ZA and ZB, which are integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 13850:2006 has been approved by CEN as a EN ISO 13850:2008 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 13850:2008
EN ISO 13850:2008 (E)
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 98/37/EC, Machinery, amended by Directive 98/79/EC.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity
with the corresponding Essential Requirement(s) 1.2.4 of that Directive and associated EFTA regulations.
WARNING: Other requirements and other EU Directives may be applicable to the products falling within the
scope of this standard.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 13850:2008
EN ISO 13850:2008 (E)
Annex ZB
(informative)
Relationship between this European Standard and the Essential Requirements of
EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive Machinery 2006/42/EC.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity
with the relevant Essential Requirements 1.2.4 of that Directive and associated EFTA regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.
5
---------------------- Page: 7 ----------------------
SIST EN ISO 13850:2008
---------------------- Page: 8 ----------------------
SIST EN ISO 13850:2008
INTERNATIONAL ISO
STANDARD 13850
Second edition
2006-11-15
Safety of machinery — Emergency
stop — Principles for design
Sécurité des machines — Arrêt d'urgence — Principes de conception
Reference number
ISO 13850:2006(E)
©
ISO 2006
---------------------- Page: 9 ----------------------
SIST EN ISO 13850:2008
ISO 13850:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 13850:2008
ISO 13850:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13850 was prepared by Technical Committee ISO/TC 199, Safety of machinery, and Technical
Committee IEC/TC 44, Safety of machinery — Electrotechnical aspects.
This second edition cancels and replaces the first edition (ISO 13850:1996), which has been technically
revised. Notably, it incorporates the following significant changes:
a) resetting of the emergency stop command is required to be manual (see 4.1.6);
b) emergency stop devices are required to use mechanical latching (see 4.4.3).
© ISO 2006 – All rights reserved iii
---------------------- Page: 11 ----------------------
SIST EN ISO 13850:2008
ISO 13850:2006(E)
Introduction
The structure of safety standards in the field of machinery is as follows.
a) Type-A standards (basis standards) give basic concepts, principles for design, and general aspects that
can be applied to machinery.
b) Type-B standards (generic safety standards) deal with one or more safety aspect(s) or one or more
type(s) of safeguard that can be used across a wide range of machinery:
⎯ type-B1 standards on particular safety aspects (e.g. safety distances, surface temperature, noise);
⎯ type-B2 standards on safeguards (e.g. two-hands controls, interlocking devices, pressure sensitive
devices, guards).
c) Type-C standards (machinery safety standards) deal with detailed safety requirements for a particular
machine or group of machines.
This International Standard is a type-B2 standard as stated in ISO 12100-1.
When provisions of a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.