SIST EN ISO 544:2024
(Main)Welding consumables - Technical delivery conditions for filler materials and fluxes - Type of product, dimensions, tolerances and markings (ISO 544:2024)
Welding consumables - Technical delivery conditions for filler materials and fluxes - Type of product, dimensions, tolerances and markings (ISO 544:2024)
ISO 544:2017 specifies technical delivery conditions for filler materials and fluxes for fusion welding.
ISO 544:2017 does not apply to other auxiliary materials such as shielding gases.
Schweißzusätze - Technische Lieferbedingungen für Schweißzusätze und Pulver - Art des Produktes, Maße, Grenzabmaße und Kennzeichnung (ISO 544:2024)
Dieses Dokument legt technische Lieferbedingungen für Schweißzusätze und Pulver zum Schmelzschweißen fest.
Dieses Dokument ist nicht anwendbar für andere Schweißhilfsstoffe wie Schutzgase.
Produits consommables pour le soudage - Conditions techniques de livraison des produits d'apport et des flux - Type de produits, dimensions, tolérances et marquage (ISO 544:2024)
ISO 544:2017 spécifie les conditions techniques de livraison des produits d'apport et des flux utilisés pour le soudage par fusion.
ISO 544:2017 ne s'applique pas aux autres produits consommables auxiliaires, tels que les gaz de protection.
Dodajni in pomožni materiali za varjenje - Tehnični dobavni pogoji za dodajne materiale in praške - Vrsta izdelka, mere, tolerance in označevanje (ISO 544:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Nadomešča:
SIST EN ISO 544:2018
Dodajni in pomožni materiali za varjenje - Tehnični dobavni pogoji za dodajne
materiale in praške - Vrsta izdelka, mere, tolerance in označevanje (ISO 544:2024)
Welding consumables - Technical delivery conditions for filler materials and fluxes - Type
of product, dimensions, tolerances and markings (ISO 544:2024)
Schweißzusätze - Technische Lieferbedingungen für Schweißzusätze und Pulver - Art
des Produktes, Maße, Grenzabmaße und Kennzeichnung (ISO 544:2024)
Produits consommables pour le soudage - Conditions techniques de livraison des
produits d'apport et des flux - Type de produits, dimensions, tolérances et marquage
(ISO 544:2024)
Ta slovenski standard je istoveten z: EN ISO 544:2024
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 544
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2024
EUROPÄISCHE NORM
ICS 25.160.20 Supersedes EN ISO 544:2017
English Version
Welding consumables - Technical delivery conditions for
filler materials and fluxes - Type of product, dimensions,
tolerances and markings (ISO 544:2024)
Produits consommables pour le soudage - Conditions Schweißzusätze - Technische Lieferbedingungen für
techniques de livraison des produits d'apport et des Schweißzusätze und Pulver - Art des Produktes, Maße,
flux - Type de produits, dimensions, tolérances et Grenzabmaße und Kennzeichnung (ISO 544:2024)
marquage (ISO 544:2024)
This European Standard was approved by CEN on 19 May 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 544:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 544:2024) has been prepared by Technical Committee ISO/TC 44 "Welding and
allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2025, and conflicting national standards shall
be withdrawn at the latest by March 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 544:2017.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 544:2024 has been approved by CEN as EN ISO 544:2024 without any modification.
International
Standard
ISO 544
Sixth edition
Welding consumables — Technical
2024-09
delivery conditions for filler
materials and fluxes — Type of
product, dimensions, tolerances
and markings
Produits consommables pour le soudage — Conditions techniques
de livraison des produits d'apport et des flux — Type de produits,
dimensions, tolérances et marquage
Reference number
ISO 544:2024(en) © ISO 2024
ISO 544:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 544:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Product type and welding process . 1
5 Dimensions and tolerances . 1
5.1 Solid wires and solid wire electrodes, tubular cored wires and tubular cored electrodes,
solid and tubular cored rods and covered electrodes .1
5.2 Solid strip electrodes .2
5.3 Cored strip electrodes and thin foils .2
5.4 Fluxes .4
6 Rounding procedure . 4
7 Condition of welding consumables . 4
7.1 Covered electrodes .4
7.2 Wires, rods, and strips .4
8 Marking . . 8
8.1 Marking on the product .8
8.1.1 Covered electrodes .8
8.1.2 Wires and strips .8
8.1.3 Rods .8
8.2 Marking on the package .8
9 Packaging. 9
10 Inspection documents . 9
Bibliography .10
iii
ISO 544:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 3, Welding consumables, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 121, Welding and allied processes, in accordance with the Agreement on
technical cooperation between ISO and CEN (Vienna Agreement).
This sixth edition cancels and replaces the fifth edition (ISO 544:2017), which has been technically revised.
The main changes compared to the previous edition are as follows:
— in 7.2, text has been added regarding delivery in larger packages;
— in Figure 1, NOTE has been revised;
— Clause 8 has been revised.
Any feedback or questions on this document should be directed to the user’s
national standards body. A complete listing of these bodies can be found at
www.iso.org/members.html. Official interpretations of ISO/TC 44 documents, where they exist, are
available from this page: https://committee.iso.org/sites/tc44/home/interpr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.