Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017)

This document specifies the methods of preparation of test specimens and the test methods to be
used in determining the properties of polyamide moulding and extrusion materials. Requirements for
handling test material and for conditioning both the test material before moulding and the specimens
before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring
properties of the materials from which these specimens are made are given. Properties and test
methods that are suitable and necessary to characterize polyamide moulding and extrusion materials
are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for, or of particular significance to, these moulding and extrusion materials are also included
in this document, as are the designatory properties viscosity number and tensile modulus of elasticity
given in ISO 16396-1.

Kunststoffe - Polyamid-(PA)-Formmassen für das Spritzgießen und die Extrusion - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 16396-2:2017)

Dieses Dokument enthält Leitlinien zur Anwendung der verfügbaren chemischen Prüfverfahren für Leder. Diese Information kann von allen verwendet werden, die am Erstellen von Spezifikationen für Leder und besonders für die Parameter von chemischen Stoffen, die Beschränkungen unterliegen, beteiligt sind.
Auflistungen von Beschränkungen unterliegenden Chemikalien enthalten viele Stoffe, die für die Leder-industrie keine Bedeutung haben. Die in diesem Dokument nicht genannten chemischen Stoffe brauchen nicht bestimmt werden, wodurch sich unnötige Analysekosten vermeiden lassen

Plastiques - Matériaux polyamides (PA) pour moulage et extrusion - Partie 2 : Préparation des éprouvettes et détermination des propriétés (ISO 16396-2:2017)

ISO 16396-2:2017 spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai à utiliser pour déterminer les propriétés des matériaux polyamides pour moulage et extrusion. Elle indique les exigences requises lors de la manipulation du matériau d'essai, ainsi que lors de conditionnement dudit matériau avant moulage et des éprouvettes avant l'essai.
Elle précise les modes opératoires et les conditions nécessaires à la préparation des éprouvettes, ainsi que les modes opératoires de mesurage des propriétés des matériaux à partir desquels ces éprouvettes sont fabriquées. Elle fournit également une liste des propriétés et des méthodes d'essai appropriées et nécessaires à la caractérisation des matériaux polyamides pour moulage et extrusion.
Les propriétés ont été choisies parmi les méthodes d'essai générales données dans l'ISO 10350‑1. Le présent document comprend en outre d'autres méthodes d'essai, présentant une importance particulière ou étant largement utilisées dans le cas de ces matériaux pour moulage et extrusion, de même que les propriétés de désignation: indice de fluidité et module d'élasticité données dans l'ISO 16396‑1.

Polimerni materiali - Poliamidni materiali (PA) za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 16396-2:2017)

Ta dokument določa metode za pripravo preskušancev in preskusnih metod za uporabo pri ugotavljanju lastnosti poliamidnih materialov za oblikovanje in ekstrudiranje. Podane so zahteve za ravnanje s preskusnim materialom ter za obdelavo preskusnega materiala pred oblikovanjem in obdelavo preskušancev pred preskusom.
Podani so postopki in pogoji za pripravo preskušancev ter postopki za merjenje
lastnosti materialov, iz katerih so izdelani preskušanci. Navedene so lastnosti in preskusne metode,
ki so primerne in nujne za opredelitev poliamidnih materialov za oblikovanje in ekstrudiranje.
Lastnosti so bile izbrane na podlagi splošnih preskusnih metod iz standarda ISO 10350-1. Druge preskusne metode, ki se splošno uporabljajo ali so posebej pomembne za te materiale za oblikovanje in ekstrudiranje, so prav tako vključene v tem dokumentu. Vključene so tudi označevalne lastnosti, ki so navedene v standardu ISO 16396-1 (viskoznostno število in natezni modul elastičnosti).

General Information

Status
Withdrawn
Public Enquiry End Date
29-Sep-2015
Publication Date
17-Apr-2017
Withdrawal Date
15-Aug-2022
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
28-Jul-2022
Due Date
20-Aug-2022
Completion Date
16-Aug-2022

Relations

Buy Standard

Standard
EN ISO 16396-2:2017
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 16396-2:2017
01-maj-2017
1DGRPHãþD
SIST EN ISO 1874-2:2014
Polimerni materiali - Poliamidni materiali (PA) za oblikovanje in ekstrudiranje - 2.
del: Priprava preskušancev in ugotavljanje lastnosti (ISO 16396-2:2017)
Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test
specimens and determination of properties (ISO 16396-2:2017)
Kunststoffe - Polyamid-(PA)-Formmassen für das Spritzgießen und die Extrusion - Teil 2:
Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 16396-2:2017)
Plastiques - Matériaux polyamides (PA) pour moulage et extrusion - Partie 2 :
Préparation des éprouvettes et détermination des propriétés (ISO 16396-2:2017)
Ta slovenski standard je istoveten z: EN ISO 16396-2:2017
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 16396-2:2017 de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 16396-2:2017

---------------------- Page: 2 ----------------------

SIST EN ISO 16396-2:2017


EN ISO 16396-2
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2017
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 1874-2:2012
English Version

Plastics - Polyamide (PA) moulding and extrusion
materials - Part 2: Preparation of test specimens and
determination of properties (ISO 16396-2:2017)
Plastiques - Matériaux polyamides (PA) pour moulage Kunststoffe - Polyamid-(PA)-Formmassen für das
et extrusion - Partie 2: Préparation des éprouvettes et Spritzgießen und die Extrusion - Teil 2: Herstellung
détermination des propriétés (ISO 16396-2:2017) von Probekörpern und Bestimmung von Eigenschaften
(ISO 16396-2:2017)
This European Standard was approved by CEN on 3 February 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16396-2:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 16396-2:2017
EN ISO 16396-2:2017 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 16396-2:2017
EN ISO 16396-2:2017 (E)
European foreword
This document (EN ISO 16396-2:2017) has been prepared by Technical Committee ISO/TC 61 “Plastics”
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2017 and conflicting national standards
shall be withdrawn at the latest by September 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 1874-2:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16396-2:2017 has been approved by CEN as EN ISO 16396-2:2017 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 16396-2:2017

---------------------- Page: 6 ----------------------

SIST EN ISO 16396-2:2017
INTERNATIONAL ISO
STANDARD 16396-2
First edition
2017-03
Plastics — Polyamide (PA) moulding
and extrusion materials —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Matériaux polyamides (PA) pour moulage et
extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 16396-2:2017(E)
©
ISO 2017

---------------------- Page: 7 ----------------------

SIST EN ISO 16396-2:2017
ISO 16396-2:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 16396-2:2017
ISO 16396-2:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Preparation of test specimens . 2
4.1 Treatment of the material before moulding or laser sintering . 2
4.2 Injection moulding . 3
4.3 Laser sintering. 3
5 Conditioning of test specimens . 5
5.1 Conditioning states of the test specimen . 5
5.2 Dry-as-moulded (DAM) state. 5
5.3 Moist state . 6
6 Determination of properties . 6
Annex A (normative) Specimen preparation using laser sintering . 9
Bibliography .10
© ISO 2017 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 16396-2:2017
ISO 16396-2:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This first edition of ISO 16396-2 cancels and replaces ISO 1874-2:2012, which has been technically
revised.
A list of all parts in the ISO 16396 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 16396-2:2017
INTERNATIONAL STANDARD ISO 16396-2:2017(E)
Plastics — Polyamide (PA) moulding and extrusion
materials —
Part 2:
Preparation of test specimens and determination of
properties
1 Scope
This document specifies the methods of preparation of test specimens and the test methods to be
used in determining the properties of polyamide moulding and extrusion materials. Requirements for
handling test material and for conditioning both the test material before moulding and the specimens
before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring
properties of the materials from which these specimens are made are given. Properties and test
methods that are suitable and necessary to characterize polyamide moulding and extrusion materials
are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for, or of particular significance to, these moulding and extrusion materials are also included
in this document, as are the designatory properties viscosity number and tensile modulus of elasticity
given in ISO 16396-1.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials —Part 1: General
principles, and moulding of multipurpose and bar test specimens
ISO 294-4, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4:
Determination of moulding shrinkage
ISO 307, Plastics — Polyamides — Determination of viscosity number
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 1110, Plastics — Polyamides — Accelerated conditioning of test specimens
ISO 1133-2, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR)
of thermoplastics — Part 2: Method for materials sensitive to time-temperature history and/or moisture
© ISO 2017 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 16396-2:2017
ISO 16396-2:2017(E)

ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density
gradient column method
ISO 1183-3, Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas
pyknometer method
ISO 3451-4, Plastics — Determination of ash — Part 4: Polyamides
ISO 8256, Plastics — Determination of tensile-impact strength
ISO 11357-3, Plastics — Differential scanning calorimetry (DSC) — Part 3: Determination of temperature
and enthalpy of melting and crystallization
ISO 15512, Plastics — Determination of water content
ISO 16396-1, Plastics — Polyamide (PA) moulding and extrusion materials — Part 1: Designation system,
marking of products and basis for specifications
ISO 20753, Plastics — Test specimens.
ISO 27547-1, Plastics — Preparation of test specimens of thermoplastic materials using mouldless
technologies — Part 1: General principles, and laser sintering of test specimens
IEC 60093, Methods of test for volume resistivity and surface resistivity of solid electrical insulating
materials
IEC 60112, Method for the determination of the proof and the comparative tracking indices of solid
insulating materials
IEC 60243-1, Electric strength of insulating materials — Test methods — Part 1: Tests at power frequencies
IEC 60250, Recommended methods for the determination of the permi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.