SIST EN 13480-5:2012/A2:2017
(Amendment)Metallic industrial piping - Part 5: Inspection and testing
Metallic industrial piping - Part 5: Inspection and testing
Specifies the requirements for inspection and testing of industrial piping as defined in EN 13480-1 to be performed on individual spools or piping systems, including supports, designed in accordance with EN 13480 3 and EN 13480-6 (if applicable), and fabricated and installed in accordance with EN 13480 4
Metallische industrielle Rohrleitungen - Teil 5: Prüfung
Tuyauteries industrielles métalliques - Partie 5: Inspection et contrôle
Kovinski industrijski cevovodi - 5. del: Pregled in preskušanje - Dopolnilo A2
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13480-5:2012/A2:2017
01-maj-2017
Kovinski industrijski cevovodi - 5. del: Pregled in preskušanje - Dopolnilo A2
Metallic industrial piping - Part 5: Inspection and testing
Metallische industrielle Rohrleitungen - Teil 5: Prüfung
Tuyauteries industrielles métalliques - Partie 5: Inspection et contrôle
Ta slovenski standard je istoveten z: EN 13480-5:2012/A2:2017
ICS:
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
SIST EN 13480-5:2012/A2:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13480-5:2012/A2:2017
---------------------- Page: 2 ----------------------
SIST EN 13480-5:2012/A2:2017
EN 13480-5:2012/A2
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2017
EUROPÄISCHE NORM
ICS 23.040.01
English Version
Metallic industrial piping - Part 5: Inspection and testing
Tuyauteries industrielles métalliques - Partie 5: Metallische industrielle Rohrleitungen - Teil 5: Prüfung
Inspection et contrôle
This amendment A2 modifies the European Standard EN 13480-5:2012; it was approved by CEN on 16 January 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13480-5:2012/A2:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13480-5:2012/A2:2017
EN 13480-5:2012/A2:2017 (E)
Contents Page
European foreword . 3
1 Modification to Clause 2. 4
2 Modification to 7.2.4 . 4
3 Modification to 7.2.5 . 7
4 Modification to 8.4.3 . 7
5 Modification to 8.4.4.3 . 8
6 Modification to Bibliography . 8
2
---------------------- Page: 4 ----------------------
SIST EN 13480-5:2012/A2:2017
EN 13480-5:2012/A2:2017 (E)
European foreword
This document (EN 13480-5:2012/A2:2017) has been prepared by Technical Committee CEN/TC 267
“Industrial piping and pipelines”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2017, and conflicting national standards
shall be withdrawn at the latest by September 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of EN 13480-
5:2012.
This document includes the text of the amendment itself. The amended/corrected pages of EN 13480-
5:2012 will be published in the new Edition 2017 of the European Standard.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 13480-5:2012/A2:2017
EN 13480-5:2012/A2:2017 (E)
1 Modification to Clause 2
Add the following normative references:
“EN ISO 10893-5:2011, Non-destructive testing of steel tubes — Part 5: Magnetic particle inspection of
seamless and welded ferromagnetic steel tubes for the detection of surface imperfections
(ISO 10893-5:2011)
ISO 3057:1998, Non-destructive testing — Metallographic replica techniques of surface examination”.
2 Modification to 7.2.4
Replace sub-clause 7.2.4 with the following: “
7.2.4 Non-destructive testing of formed parts
7.2.4.1 General
All formed parts shall be subject to non-destructive testing. Depending on material, dimensions and
type of forming process testing may include:
a) visual testing;
b) wall thickness measurements;
c) dimensional checks (ovality, angle of bend etc.) and tolerances (see EN 13480-4);
d) hardness tests;
e) testing for surface imperfections (magnetic particle or penetrant testing);
on formed parts of each component or batch of identical components.
Material, heat treatment conditions, heat treatment lot, degree of deformation shall be considered in the
definition of the batch.
Replicas of the surface structure in the tension zone may be required in case of lifetime monitoring for
creep range application.
Ultrasonic testing may be
...
SLOVENSKI STANDARD
SIST EN 13480-5:2012/oprA2:2014
01-september-2014
Kovinski industrijski cevovodi - 5. del: Pregled in preskušanje
Metallic industrial piping - Part 5: Inspection and testing
Metallische industrielle Rohrleitungen - Teil 5: Prüfung
Tuyauteries industrielles métalliques - Partie 5: Inspection et contrôle
Ta slovenski standard je istoveten z: EN 13480-5:2012/prA2
ICS:
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
SIST EN 13480-5:2012/oprA2:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13480-5:2012/oprA2:2014
---------------------- Page: 2 ----------------------
SIST EN 13480-5:2012/oprA2:2014
EUROPEAN STANDARD
DRAFT
EN 13480-5:2012
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
April 2014
ICS 23.040.01
English Version
Metallic industrial piping - Part 5: Inspection and testing
Tuyauteries industrielles métalliques - Partie 5: Inspection Metallische industrielle Rohrleitungen - Teil 5: Prüfung
et contrôle
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 267.
This draft amendment A2, if approved, will modify the European Standard EN 13480-5:2012. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13480-5:2012/prA2:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13480-5:2012/oprA2:2014
EN 13480-5:2012/prA2:2014 (E)
Contents Page
Foreword .3
1 Modification to Clause 2 .4
2 Modification to 7.2.4 .4
3 Modification to 7.2.5 .7
4 Modification to 8.4.3 .7
5 Modification to 8.4.4.3 .8
6 Modification to Bibliography .8
2
---------------------- Page: 4 ----------------------
SIST EN 13480-5:2012/oprA2:2014
EN 13480-5:2012/prA2:2014 (E)
Foreword
This document (EN 13480-5:2012/prA2:2014) has been prepared by Technical Committee CEN/TC 267
“Industrial piping and pipelines”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
This document includes the text of the amendment itself. The amended/corrected pages of EN 13480-5:2012
will be published as Issue 3 of the European Standard.
3
---------------------- Page: 5 ----------------------
SIST EN 13480-5:2012/oprA2:2014
EN 13480-5:2012/prA2:2014 (E)
1 Modification to Clause 2
Add the following normative references:
EN ISO 10893-5:2011, Non-destructive testing of steel tubes — Part 5: Magnetic particle inspection of
seamless and welded ferromagnetic steel tubes for the detection of surface imperfections (ISO 10893-5:2011)
ISO 3057:1998, Non-destructive testing — Metallographic replica techniques of surface examination
2 Modification to 7.2.4
Replace sub-clause 7.2.4 by the following:
7.2.4 Non-destructive testing of formed parts
7.2.4.1 General
Depending on material, dimensions and type of forming process testing may include:
a) visual testing;
b) wall thickness measurements;
c) dimensional checks (ovality, angle of bend etc.) and tolerances (see EN 13480-4);
d) hardness tests;
e) ultrasonic testing for volumetric (internal) imperfections in longitudinal and transversal direction;
f) testing for surface imperfections (magnetic particle or penetrant testing);
g) replicas of the surface structure in the tension zone (in case life monitoring is required for creep range
applications)
on each component or batch of identical components.
Material, heat treatment conditions, heat treatment lot, degree of deformation shall be considered in the
definition of the batch.
NOTE A customary interpretation of a heat treatment lot is the entire content of a furnace of a single heat treatment.
7.2.4.2 Induction bending
Material and material surfaces shall be suitable for induction bending. EN ISO 10893-5 specifies surface
qualities and acceptance levels. The acceptance levels shall be agreed, considering material, dimensions and
service (creep, fatigue).
Induction bend
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.