SIST EN 60309-2:2000/A11:2006
(Amendment)Plugs, socket-outlets and couplers for industrial purposes -- Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories
Plugs, socket-outlets and couplers for industrial purposes -- Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories
Applies to plugs and socket-outlets, cable couplers and appliance couplers with a rated operating voltage not exceeding 690 V, 500 Hz and a rated current not exceeding 125 A, primarily intended for industrial use, either indoors or outdoors. This standard applies to plugs and socket-outlets, cable couplers and appliance couplers with pins and contact tubes of standardized configurations. This standard applies to plugs and socket-outlets, cable couplers and appliance couplers, hereinafter referred to as accessories, for use when the ambient temperature is normally within the range -25 °C to 40 °C. The use of these accessories on building sites and for agricultural, commercial and domestic applications is not precluded. Socket-outlets or appliance inlets incorperated in or fixed to electrical equipment are within the scope of this standard. This standard also applies to accessories intended to be used in extralow voltage installations. This European Standard applies to Series I products only. Series II products are not allowed and not suitable for use in Europe: reference and requirements for. Series II products are reported in this standard for information only and shall be ignored. This European Standard applies to products intended to be used with cables with metric sizes (mm2) only. Reference and requirements to AWG and MCM cables are present in the relevant IEC publication and they are reported in this standard for information only. See Annex ZC for a list of references to Series II and/or AWG/MCM cable which are excluded from this standard.
Stecker, Steckdosen und Kupplungen für industrielle Anwendungen -- Teil 2: Anforderungen und Hauptmaße für die Austauschbarkeit von Stift- und Buchsensteckvorrichtungen
Prises de courant pour usages industriels -- Partie 2: Règles d'interchangeabilité dimensionnelle pour les appareils à broches et alvéoles
Vtiči, vtičnice in spojke za industrijske namene – 2. del: Zahteve za dimenzijsko medsebojno zamenjljivost pri priboru s trni ali cevastimi kontakti
Ta točka 1. dela ali 2. dela se uporablja, razen kot sledi: Zamenjava prvega odstavka z naslednjim besedilom: Ta del standarda IEC 60309 se uporablja za avtonomne izdelke, ki so združeni v enem ohišju, vtičnici ali priključku v skladu s standardom IEC 60309-1 ali IEC 60309-2, ter stikalno napravo z nazivno obratovalno napetostjo, ki ne presega 690 V enosmerne ali izmenične napetosti in 500 Hz, ter nazivnim tokom, ki ne presega 250 A, in so namenjeni predvsem za industrijsko uporabo v notranjih prostorih ali na prostem. Ti izdelki lahko vsebujejo zaporne in/ali varovalne naprave.
General Information
Relations
Standards Content (Sample)
EUROPEAN STANDARD EN 60309-2/A11
NORME EUROPÉENNE
EUROPÄISCHE NORM May 2004
ICS 29.120.30
English version
Plugs, socket-outlets and couplers for industrial purposes
Part 2: Dimensional interchangeability requirements
for pin and contact-tube accessories
Prises de courant pour usages industriels Stecker, Steckdosen und Kupplungen
Partie 2: Règles d'interchangeabilité für industrielle Anwendungen
dimensionnelle pour les appareils Teil 2: Anforderungen und Hauptmaße
à broches et alvéoles für die Austauschbarkeit von Stift-
und Buchsensteckvorrichtungen
This amendment A11 modifies the European Standard EN 60309-2:1999; it was approved by CENELEC
on 2004-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this amendment the status of a national standard without any
alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60309-2:1999/A11:2004 E
---------------------- Page: 1 ----------------------
EN 60309-2:19
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.