SIST-TS CEN/TS 1071-8:2005
(Main)Advanced technical ceramics - Methods of test for ceramic coatings - Part 8: Rockwell indentation test for evaluation of adhesion
Advanced technical ceramics - Methods of test for ceramic coatings - Part 8: Rockwell indentation test for evaluation of adhesion
This document specifies a method for the evaluation of the adhesion of ceramic coatings by indentation with a Rockwell diamond indenter. The formation of cracks after indentation may also reveal cohesive failure. The indentations are made with a Rockwell hardness test instrument.
The method described in this document may also be suitable for evaluating the adhesion of metallic coatings.
Hochleistungskeramik - Verfahren zur Prüfung keramischer Schichten - Teil 8: Rockwell-Eindringprüfung zur Bewertung der Haftung
Dieses Dokument legt ein Verfahren zur Bewertung der Haftung keramischer Schichten fest, bei dem in der Schicht mit einem für die Rockwell Härteprüfung angewendeten Diamant Eindringkörper ein Eindruck erzeugt wird. Rissbildung am Eindruck kann auf ein Kohäsionsversagen hinweisen. Die Eindringprüfung wird mit einer für die Härteprüfung nach Rockwell vorgesehenen Prüfmaschine durchgeführt.
Nach dem in diesem Dokument beschriebenen Verfahren darf auch die Haftung metallischer Schichten bewertet werden.
Céramiques techniques avancées - Méthodes d'essai pour revetements céramiques - Partie 8: Evaluation de l'adhérence par test de pénétration Rockwell
Sodobna tehnična keramika – Metode za preskušanje keramičnih prevlek – 8. del: Preskus z vtiskanjem po Rockwellu za ovrednotenje sprijemnosti
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 1071-8:2005
01-januar-2005
6RGREQDWHKQLþQDNHUDPLND±0HWRGH]DSUHVNXãDQMHNHUDPLþQLKSUHYOHN±GHO
3UHVNXV]YWLVNDQMHPSR5RFNZHOOX]DRYUHGQRWHQMHVSULMHPQRVWL
Advanced technical ceramics - Methods of test for ceramic coatings - Part 8: Rockwell
indentation test for evaluation of adhesion
Hochleistungskeramik - Verfahren zur Prüfung keramischer Schichten - Teil 8: Rockwell-
Eindringprüfung zur Bewertung der Haftung
Céramiques techniques avancées - Méthodes d'essai pour revetements céramiques -
Partie 8: Evaluation de l'adhérence par test de pénétration Rockwell
Ta slovenski standard je istoveten z: CEN/TS 1071-8:2004
ICS:
25.220.99 Druge obdelave in prevleke Other treatments and
coatings
81.060.30 Sodobna keramika Advanced ceramics
SIST-TS CEN/TS 1071-8:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 1071-8:2005
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 1071-8:2005
TECHNICAL SPECIFICATION
CEN/TS 1071-8
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
September 2004
ICS 81.060.30
English version
Advanced technical ceramics - Methods of test for ceramic
coatings - Part 8: Rockwell indentation test for evaluation of
adhesion
Céramiques techniques avancées - Méthodes d'essai pour Hochleistungskeramik - Verfahren zur Prüfung keramischer
revêtements céramiques - Partie 8: Evaluation de Schichten - Teil 8: Rockwell-Eindringprüfung zur Bewertung
l'adhérence par test de pénétration Rockwell der Haftung
This Technical Specification (CEN/TS) was approved by CEN on 6 June 2004 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 1071-8:2004: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 1071-8:2005
CEN/TS 1071-8:2004 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Principle.4
4 Apparatus .4
5 Sampling and preparation of test specimens.4
6 Method of test .5
7 Limits .6
8 Test report .6
Annex A (informative) Indentation and classification.7
Bibliography .9
2
---------------------- Page: 4 ----------------------
SIST-TS CEN/TS 1071-8:2005
CEN/TS 1071-8:2004 (E)
Foreword
This document (CEN/TS 1071-8:2004) has been prepared by Technical Committee CEN/TC 184 “Advanced
technical ceramics”, the secretariat of which is held by BSI.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and the United Kingdom.
EN 1071 Advanced technical ceramics — Methods of test for ceramic coatings consists of eleven parts:
Part 1: Determination of coating thickness by contact probe profilometer
Part 2: Determination of coating thickness by the crater grinding method
Part 3: Determination of adhesive and other mechanical failure modes by a scratch test
Part 4: Determination of chemical composition by electron probe microanalysis (EPMA)
Part 5: Determination of porosity
Part 6: Determination of the abrasion resistance of coatings by a micro-abrasion wear test
Part 7: Determination of hardness and modulus by depth sensing indentation
Part 8: Rockwell indentation test for evaluation of adhesion
Part 9: Determination of fracture strain
Part 10: Determination of coating thickness by cross sectioning
Part 11: Measurement of internal stress with the Stoney formula.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN/TS 1071-8:2005
CEN/TS 1071-8:2004 (E)
1 Scope
This document specifies a method for the evaluation of the adhesion of ceramic coatings by indentation with a
Rockwell diamond indenter. The formation of cracks after indentation may also reveal cohesive failure. The
indentations are made with a Rockwell hardness test instrument.
The method described in this document may also be suitable for evaluating the adhesion of metallic coatings.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.