SIST ISO 15202-2:2020
(Main)Workplace air - Determination of metals and metalloids in airborne particulate matter by inductively coupled plasma atomic emission spectrometry - Part 2: Sample preparation
Workplace air - Determination of metals and metalloids in airborne particulate matter by inductively coupled plasma atomic emission spectrometry - Part 2: Sample preparation
This document specifies a number of suitable methods for preparing test solutions from samples of airborne particulate matter collected using the method specified in ISO 15202‑1, for subsequent determination of metals and metalloids by ICP‑AES using the method specified in ISO 15202‑3. It contains information about the applicability of the methods with respect to the measurement of metals and metalloids for which limit values have been set. The methods can also be used in the measurement of some metals and metalloids for which limit values have not been set but no information about its applicability is provided in this case.
NOTE The sample preparation methods described in this document are generally suitable for use with analytical techniques other than ICP‑AES, e.g. atomic absorption spectrometry (AAS) by ISO 8518[5] and ISO 11174[10] and inductively coupled plasma mass spectrometry (ICP‑MS) by ISO 30011[11].
The method specified in Annex B is applicable when making measurements for comparison with limit values for soluble metal or metalloid compounds.
One or more of the sample dissolution methods specified in Annexes C through H are applicable when making measurements for comparison with limit values for total metals and metalloids and their compounds. Information on the applicability of individual methods is given in the scope of the annex in which the method is specified.
The following is a non-exclusive list of metals and metalloids for which limit values have been set (see References [14] and [15]) and for which one or more of the sample dissolution methods specified in this document are applicable. However, there is no information available on the effectiveness of any of the specified sample dissolution methods for those elements in italics.
Aluminium
Calcium
Magnesium
Selenium
Tungsten
Antimony
Chromium
Manganese
Silver
Uranium
Arsenic
Cobalt
Mercury
Sodium
Vanadium
Barium
Copper
Molybdenum
Strontium
Yttrium
Beryllium
Hafnium
Nickel
Tantalum
Zinc
Bismuth
Indium
Phosphorus
Tellurium
Zirconium
Boron
Iron
Platinum
Thallium
Caesium
Lead
Potassium
Tin
Cadmium
Lithium
Rhodium
Titanium
ISO 15202 is not applicable to the determination of elemental mercury or arsenic trioxide, since mercury vapour and arsenic trioxide vapour are not collected using the sampling method specified in ISO 15202‑1.
Air des lieux de travail - Détermination des métaux et métalloïdes dans les particules en suspension dans l'air par spectrométrie d'émission atomique avec plasma à couplage inductif - Partie 2: Préparation des échantillons
Le présent document spécifie plusieurs méthodes appropriées de préparation de solutions d'essai à partir d'échantillons de matière particulaire en suspension dans l'air prélevés en utilisant la méthode spécifiée dans l'ISO 15202-1, en vue du dosage des métaux et métalloïdes par ICP-AES à l'aide de la méthode spécifiée dans l'ISO 15202-3. Il contient des informations relatives à l'applicabilité des méthodes par rapport au dosage de métaux et métalloïdes pour lesquels des valeurs limites ont été établies. Ces méthodes peuvent également être utilisées pour le dosage de certains métaux et métalloïdes pour lesquels les valeurs limites n'ont pas été établies mais, dans ce cas, aucune information sur leur applicabilité n'est disponible.
NOTE Les méthodes de préparation d'échantillons décrites dans le présent document sont généralement appropriées pour une utilisation conjointe avec d'autres techniques d'analyse que l'ICP-AES, par exemple la spectrométrie d'absorption atomique (AAS) définie dans l'ISO 8518[5] et l'ISO 11174[10] et la spectrométrie de masse avec plasma à couplage inductif (ICP-MS) définie dans l'ISO 30011[11].
La méthode spécifiée à l'Annexe B est applicable pour effectuer des mesurages de comparaison avec des valeurs limites de composés solubles de métaux ou métalloïdes.
Une ou plusieurs des méthodes de mise en solution d'échantillon spécifiées aux Annexes C à H sont applicables pour effectuer des mesurages de comparaison avec des valeurs limites de métaux et métalloïdes totaux et leurs composés. Des informations concernant les possibilités d'application des méthodes individuelles sont données dans le domaine d'application de l'annexe dans laquelle la méthode est spécifiée.
L'ISO 15202 n'est pas applicable pour la détermination du mercure élémentaire ni de l'anhydride arsénieux, dans la mesure où les vapeurs de mercure et les vapeurs d'anhydride arsénieux ne sont pas recueillies en utilisant la méthode de prélèvement spécifiée dans l'ISO 15202-1.
Zrak na delovnem mestu - Določevanje kovin in polkovin v lebdečih delcih z atomsko emisijsko spektrometrijo z induktivno sklopljeno plazmo - 2. del: Priprava vzorcev
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2020
Nadomešča:
SIST ISO 15202-2:2013
Zrak na delovnem mestu - Določevanje kovin in polkovin v lebdečih delcih z
atomsko emisijsko spektrometrijo z induktivno sklopljeno plazmo - 2. del: Priprava
vzorcev
Workplace air - Determination of metals and metalloids in airborne particulate matter by
inductively coupled plasma atomic emission spectrometry - Part 2: Sample preparation
Air des lieux de travail - Détermination des métaux et métalloïdes dans les particules en
suspension dans l'air par spectrométrie d'émission atomique avec plasma à couplage
inductif - Partie 2: Préparation des échantillons
Ta slovenski standard je istoveten z: ISO 15202-2:2020
ICS:
13.040.30 Kakovost zraka na delovnem Workplace atmospheres
mestu
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 15202-2
Third edition
2020-05
Workplace air — Determination of
metals and metalloids in airborne
particulate matter by inductively
coupled plasma atomic emission
spectrometry —
Part 2:
Sample preparation
Air des lieux de travail — Détermination des métaux et métalloïdes
dans les particules en suspension dans l'air par spectrométrie
d'émission atomique avec plasma à couplage inductif —
Partie 2: Préparation des échantillons
Reference number
©
ISO 2020
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Principle . 3
5 Requirements . 3
6 Reactions . 3
7 Reagents . 3
8 Laboratory apparatus . 4
9 Procedure. 4
9.1 Soluble metal and metalloid compounds . 4
9.2 Total metals and metalloids and their compounds . 5
9.3 Mixed exposure . 5
10 Special cases . 5
10.1 Action to be taken if there is doubt about the effectiveness of the selected sample
dissolution method . 5
10.2 Action to be taken when particles have become dislodged from the filter during
transportation . 6
10.3 Action to be taken regarding sampler wall deposits . 6
11 Laboratory records . 6
Annex A (informative) Safety precautions to be observed when using hydrofluoric and
perchloric acids . 7
Annex B (normative) Sample dissolution method for soluble metal and metalloid compounds .8
Annex C (normative) Sample dissolution using nitric acid and hydrochloric acid on a hotplate .14
Annex D (normative) Sample dissolution using hydrofluoric and nitric acids and ultrasonic
agitation . .18
Annex E (normative) Sample dissolution using sulfuric acid and hydrogen peroxide on a
hotplate .21
Annex F (normative) Sample dissolution using nitric acid and perchloric acid on a hotplate .25
Annex G (normative) Sample dissolution in a closed vessel microwave dissolution system .29
Annex H (normative) Sample dissolution at 95 °C using a hot block .35
Annex I (normative) Action to be taken when there is visible, undissolved, particulate
material after sample dissolution .38
Annex J (informative) Sampler wall deposits .44
Bibliography .47
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 146, Air quality, Subcommittee SC 2,
Workplace atmospheres.
This third edition cancels and replaces the second edition (ISO 15202-2:2012), which has been
technically revised. The main changes compared to the previous edition are as follows:
— Definitions that appear in ISO 18158 have been removed from ISO 15202-2, with ISO 18158 being
added as a reference (replacing references to EN 1540).
— References to EN 482 have been replaced with ISO 20581, and references to EN 13890 have been
replaced with ISO 21832.
— Information regarding digestion of acid-soluble internal capsules has been added to Annexes C, D, E,
F, G and H.
— The text has been editorially updated.
A list of all parts in the ISO 15202 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
Introduction
The health of workers in many industries is at risk through exposure by inhalation of toxic metals
and metalloids. Industrial hygienists and other public health professionals need to determine the
effectiveness of measures taken to control workers' exposure, and this is generally achieved by making
workplace air measurements. This document has been published in order to make available a method
for making valid exposure measurements for a wide range of metals and metalloids in use in industry.
It will be of benefit to agencies concerned with health and safety at work, industrial hygienists and
other public health professionals, analytical laboratories, industrial users of metals and metalloids and
their workers.
ISO 15202, published in three parts, specifies a generic method for the determination of the mass
concentration of metals and metalloids in workplace air using inductively coupled plasma atomic
emission spectrometry (ICP-AES).
— ISO 15202-1 gives details of relevant International, European and National Standards which specify
characteristics, performance requirements and test methods relating to sampling equipment. It
also augments guidance provided elsewhere on assessment strategy and measurement strategy,
as well as specifying a method for collecting samples of airborne particulate matter for subsequent
chemical analysis.
— ISO 15202-2 describes a number of procedures for preparing sample solutions for analysis by
ICP-AES.
— ISO 15202-3 gives requirements and test methods for the analysis of sample solutions by ICP-AES.
The sample preparation methods described in this part of ISO 15202 are generally suitable for use with
analytical techniques other than ICP-AES; e.g. atomic absorption spectroscopy (AAS) and inductively
coupled plasma mass spectrometry (ICP-MS).
It has been assumed in the drafting of this document that the execution of its provisions and the
interpretation of the results obtained are entrusted to appropriately qualified and experienced people.
INTERNATIONAL STANDARD ISO 15202-2:2020(E)
Workplace air — Determination of metals and metalloids
in airborne particulate matter by inductively coupled
plasma atomic emission spectrometry —
Part 2:
Sample preparation
WARNING — The use of this document may involve hazardous materials, operations and
equipment. This document does not purport to address any safety problems associated with
its use. It is the responsibility of the user of this document to establish appropriate safety and
health practices and determine the applicability of regulatory limitations prior to use.
1 Scope
This document specifies a number of suitable methods for preparing test solutions from samples of
airborne particulate matter collected using the me
...
INTERNATIONAL ISO
STANDARD 15202-2
Third edition
2020-05
Workplace air — Determination of
metals and metalloids in airborne
particulate matter by inductively
coupled plasma atomic emission
spectrometry —
Part 2:
Sample preparation
Air des lieux de travail — Détermination des métaux et métalloïdes
dans les particules en suspension dans l'air par spectrométrie
d'émission atomique avec plasma à couplage inductif —
Partie 2: Préparation des échantillons
Reference number
©
ISO 2020
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Principle . 3
5 Requirements . 3
6 Reactions . 3
7 Reagents . 3
8 Laboratory apparatus . 4
9 Procedure. 4
9.1 Soluble metal and metalloid compounds . 4
9.2 Total metals and metalloids and their compounds . 5
9.3 Mixed exposure . 5
10 Special cases . 5
10.1 Action to be taken if there is doubt about the effectiveness of the selected sample
dissolution method . 5
10.2 Action to be taken when particles have become dislodged from the filter during
transportation . 6
10.3 Action to be taken regarding sampler wall deposits . 6
11 Laboratory records . 6
Annex A (informative) Safety precautions to be observed when using hydrofluoric and
perchloric acids . 7
Annex B (normative) Sample dissolution method for soluble metal and metalloid compounds .8
Annex C (normative) Sample dissolution using nitric acid and hydrochloric acid on a hotplate .14
Annex D (normative) Sample dissolution using hydrofluoric and nitric acids and ultrasonic
agitation . .18
Annex E (normative) Sample dissolution using sulfuric acid and hydrogen peroxide on a
hotplate .21
Annex F (normative) Sample dissolution using nitric acid and perchloric acid on a hotplate .25
Annex G (normative) Sample dissolution in a closed vessel microwave dissolution system .29
Annex H (normative) Sample dissolution at 95 °C using a hot block .35
Annex I (normative) Action to be taken when there is visible, undissolved, particulate
material after sample dissolution .38
Annex J (informative) Sampler wall deposits .44
Bibliography .47
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 146, Air quality, Subcommittee SC 2,
Workplace atmospheres.
This third edition cancels and replaces the second edition (ISO 15202-2:2012), which has been
technically revised. The main changes compared to the previous edition are as follows:
— Definitions that appear in ISO 18158 have been removed from ISO 15202-2, with ISO 18158 being
added as a reference (replacing references to EN 1540).
— References to EN 482 have been replaced with ISO 20581, and references to EN 13890 have been
replaced with ISO 21832.
— Information regarding digestion of acid-soluble internal capsules has been added to Annexes C, D, E,
F, G and H.
— The text has been editorially updated.
A list of all parts in the ISO 15202 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
Introduction
The health of workers in many industries is at risk through exposure by inhalation of toxic metals
and metalloids. Industrial hygienists and other public health professionals need to determine the
effectiveness of measures taken to control workers' exposure, and this is generally achieved by making
workplace air measurements. This document has been published in order to make available a method
for making valid exposure measurements for a wide range of metals and metalloids in use in industry.
It will be of benefit to agencies concerned with health and safety at work, industrial hygienists and
other public health professionals, analytical laboratories, industrial users of metals and metalloids and
their workers.
ISO 15202, published in three parts, specifies a generic method for the determination of the mass
concentration of metals and metalloids in workplace air using inductively coupled plasma atomic
emission spectrometry (ICP-AES).
— ISO 15202-1 gives details of relevant International, European and National Standards which specify
characteristics, performance requirements and test methods relating to sampling equipment. It
also augments guidance provided elsewhere on assessment strategy and measurement strategy,
as well as specifying a method for collecting samples of airborne particulate matter for subsequent
chemical analysis.
— ISO 15202-2 describes a number of procedures for preparing sample solutions for analysis by
ICP-AES.
— ISO 15202-3 gives requirements and test methods for the analysis of sample solutions by ICP-AES.
The sample preparation methods described in this part of ISO 15202 are generally suitable for use with
analytical techniques other than ICP-AES; e.g. atomic absorption spectroscopy (AAS) and inductively
coupled plasma mass spectrometry (ICP-MS).
It has been assumed in the drafting of this document that the execution of its provisions and the
interpretation of the results obtained are entrusted to appropriately qualified and experienced people.
INTERNATIONAL STANDARD ISO 15202-2:2020(E)
Workplace air — Determination of metals and metalloids
in airborne particulate matter by inductively coupled
plasma atomic emission spectrometry —
Part 2:
Sample preparation
WARNING — The use of this document may involve hazardous materials, operations and
equipment. This document does not purport to address any safety problems associated with
its use. It is the responsibility of the user of this document to establish appropriate safety and
health practices and determine the applicability of regulatory limitations prior to use.
1 Scope
This document specifies a number of suitable methods for preparing test solutions from samples of
airborne particulate matter collected using the method specified in ISO 15202-1, for subsequent
determination of metals and metalloids by ICP-AES using the method specified in ISO 15202-3. It
contains information about the applicability of the methods with respect to the measurement of metals
and metalloids for which limit values have been set. The methods can also be used in the measurement
of some metals and metalloids for which limit values have not been set but no information about its
applicability is provided in this case.
NOTE The sample preparation methods described in this document are generally suitable for use with
[5]
analytical techniques other than ICP-AES, e.g. atomic absorption spectrometry (AAS) by ISO 8518 and
[10] [11]
ISO 11174 and inductively coupled plasma mass spectrometry (ICP-MS) by ISO 30011 .
The method specified in Annex B is applicable when making measurements for comparison with limit
values for soluble metal or metalloid compounds.
One or more of the sample dissolution methods specified in Annexes C through H are applicable when
making measurements for comparison with limit values for total metals and metalloids and their
compounds. Information on the applicability of individual methods is given in the scope of the annex in
which the method is specified.
The
...
INTERNATIONAL ISO
STANDARD 15202-2
Third edition
2020-05
Workplace air — Determination of
metals and metalloids in airborne
particulate matter by inductively
coupled plasma atomic emission
spectrometry —
Part 2:
Sample preparation
Air des lieux de travail — Détermination des métaux et métalloïdes
dans les particules en suspension dans l'air par spectrométrie
d'émission atomique avec plasma à couplage inductif —
Partie 2: Préparation des échantillons
Reference number
©
ISO 2020
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Principle . 3
5 Requirements . 3
6 Reactions . 3
7 Reagents . 3
8 Laboratory apparatus . 4
9 Procedure. 4
9.1 Soluble metal and metalloid compounds . 4
9.2 Total metals and metalloids and their compounds . 5
9.3 Mixed exposure . 5
10 Special cases . 5
10.1 Action to be taken if there is doubt about the effectiveness of the selected sample
dissolution method . 5
10.2 Action to be taken when particles have become dislodged from the filter during
transportation . 6
10.3 Action to be taken regarding sampler wall deposits . 6
11 Laboratory records . 6
Annex A (informative) Safety precautions to be observed when using hydrofluoric and
perchloric acids . 7
Annex B (normative) Sample dissolution method for soluble metal and metalloid compounds .8
Annex C (normative) Sample dissolution using nitric acid and hydrochloric acid on a hotplate .14
Annex D (normative) Sample dissolution using hydrofluoric and nitric acids and ultrasonic
agitation . .18
Annex E (normative) Sample dissolution using sulfuric acid and hydrogen peroxide on a
hotplate .21
Annex F (normative) Sample dissolution using nitric acid and perchloric acid on a hotplate .25
Annex G (normative) Sample dissolution in a closed vessel microwave dissolution system .29
Annex H (normative) Sample dissolution at 95 °C using a hot block .35
Annex I (normative) Action to be taken when there is visible, undissolved, particulate
material after sample dissolution .38
Annex J (informative) Sampler wall deposits .44
Bibliography .47
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 146, Air quality, Subcommittee SC 2,
Workplace atmospheres.
This third edition cancels and replaces the second edition (ISO 15202-2:2012), which has been
technically revised. The main changes compared to the previous edition are as follows:
— Definitions that appear in ISO 18158 have been removed from ISO 15202-2, with ISO 18158 being
added as a reference (replacing references to EN 1540).
— References to EN 482 have been replaced with ISO 20581, and references to EN 13890 have been
replaced with ISO 21832.
— Information regarding digestion of acid-soluble internal capsules has been added to Annexes C, D, E,
F, G and H.
— The text has been editorially updated.
A list of all parts in the ISO 15202 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
Introduction
The health of workers in many industries is at risk through exposure by inhalation of toxic metals
and metalloids. Industrial hygienists and other public health professionals need to determine the
effectiveness of measures taken to control workers' exposure, and this is generally achieved by making
workplace air measurements. This document has been published in order to make available a method
for making valid exposure measurements for a wide range of metals and metalloids in use in industry.
It will be of benefit to agencies concerned with health and safety at work, industrial hygienists and
other public health professionals, analytical laboratories, industrial users of metals and metalloids and
their workers.
ISO 15202, published in three parts, specifies a generic method for the determination of the mass
concentration of metals and metalloids in workplace air using inductively coupled plasma atomic
emission spectrometry (ICP-AES).
— ISO 15202-1 gives details of relevant International, European and National Standards which specify
characteristics, performance requirements and test methods relating to sampling equipment. It
also augments guidance provided elsewhere on assessment strategy and measurement strategy,
as well as specifying a method for collecting samples of airborne particulate matter for subsequent
chemical analysis.
— ISO 15202-2 describes a number of procedures for preparing sample solutions for analysis by
ICP-AES.
— ISO 15202-3 gives requirements and test methods for the analysis of sample solutions by ICP-AES.
The sample preparation methods described in this part of ISO 15202 are generally suitable for use with
analytical techniques other than ICP-AES; e.g. atomic absorption spectroscopy (AAS) and inductively
coupled plasma mass spectrometry (ICP-MS).
It has been assumed in the drafting of this document that the execution of its provisions and the
interpretation of the results obtained are entrusted to appropriately qualified and experienced people.
INTERNATIONAL STANDARD ISO 15202-2:2020(E)
Workplace air — Determination of metals and metalloids
in airborne particulate matter by inductively coupled
plasma atomic emission spectrometry —
Part 2:
Sample preparation
WARNING — The use of this document may involve hazardous materials, operations and
equipment. This document does not purport to address any safety problems associated with
its use. It is the responsibility of the user of this document to establish appropriate safety and
health practices and determine the applicability of regulatory limitations prior to use.
1 Scope
This document specifies a number of suitable methods for preparing test solutions from samples of
airborne particulate matter collected using the method specified in ISO 15202-1, for subsequent
determination of metals and metalloids by ICP-AES using the method specified in ISO 15202-3. It
contains information about the applicability of the methods with respect to the measurement of metals
and metalloids for which limit values have been set. The methods can also be used in the measurement
of some metals and metalloids for which limit values have not been set but no information about its
applicability is provided in this case.
NOTE The sample preparation methods described in this document are generally suitable for use with
[5]
analytical techniques other than ICP-AES, e.g. atomic absorption spectrometry (AAS) by ISO 8518 and
[10] [11]
ISO 11174 and inductively coupled plasma mass spectrometry (ICP-MS) by ISO 30011 .
The method specified in Annex B is applicable when making measurements for comparison with limit
values for soluble metal or metalloid compounds.
One or more of the sample dissolution methods specified in Annexes C through H are applicable when
making measurements for comparison with limit values for total metals and metalloids and their
compounds. Information on the applicability of individual methods is given in the scope of the annex in
which the method is specified.
The
...
NORME ISO
INTERNATIONALE 15202-2
Troisième édition
2020-05
Air des lieux de travail —
Détermination des métaux et
métalloïdes dans les particules
en suspension dans l'air par
spectrométrie d'émission atomique
avec plasma à couplage inductif —
Partie 2:
Préparation des échantillons
Workplace air — Determination of metals and metalloids in airborne
particulate matter by inductively coupled plasma atomic emission
spectrometry —
Part 2: Sample preparation
Numéro de référence
©
ISO 2020
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2020
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2020 – Tous droits réservés
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 2
3 Termes et définitions . 2
4 Principe . 3
5 Exigences . 3
6 Réactions . 4
7 Réactifs . 4
8 Appareillage de laboratoire . 4
9 Mode opératoire. 5
9.1 Composés solubles de métaux et métalloïdes . 5
9.2 Métaux et métalloïdes totaux et leurs composés . 5
9.3 Exposition mixte . 6
10 Cas particuliers . 6
10.1 Action à mener s’il existe un doute concernant l’efficacité de la méthode de mise
en solution d’échantillon choisie . 6
10.2 Action à mener lorsque les particules se sont détachées du filtre pendant le transport . 7
10.3 Action à mener en présence de dépôts sur les parois du dispositif de prélèvement . 7
11 Enregistrements de laboratoire . 7
Annexe A (informative) Précautions de sécurité à respecter lors de l’utilisation d’acide
fluorhydrique et perchlorique . 8
Annexe B (normative) Méthode de mise en solution d’échantillon pour les composés
solubles de métaux et métalloïdes . 9
Annexe C (normative) Mise en solution d’échantillon à l’aide d’acide nitrique et d’acide
chlorhydrique sur plaque chauffante .15
Annexe D (normative) Mise en solution d’échantillon à l’aide d’acide fluorhydrique et
d’acide nitrique par agitation par ultrason .19
Annexe E (normative) Mise en solution en utilisant de l’acide sulfurique et du peroxyde
d’hydrogène sur plaque chauffante .23
Annexe F (normative) Mise en solution en utilisant de l’acide nitrique et de l’acide
perchlorique sur plaque chauffante .28
Annexe G (normative) Mise en solution d’échantillon dans un système de digestion par
micro-ondes en récipient fermé .33
Annexe H (normative) Mise en solution d’échantillon à 95 °C sur bloc chauffant .39
Annexe I (normative) Action à mener en présence de particules visibles, non dissoutes,
après mise en solution d’échantillon .43
Annexe J (informative) Dépôts sur les parois des dispositifs de prélèvement .49
Bibliographie .52
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 146, Qualité de l’air, sous-comité SC 2,
Atmosphères des lieux de travail.
Cette troisième édition annule et remplace la deuxième édition (ISO 15202-2:2012), qui a fait l’objet
d’une révision technique. Les principales modifications par rapport à l’édition précédente sont les
suivantes:
— les définitions figurant dans l’ISO 18158 ont été supprimées de l’ISO 15202-2, et la référence à
l’ISO 18158 a été ajoutée en remplacement des références à l’EN 1540;
— les références à l’EN 482 ont été remplacées par l’ISO 20581, et les références à l’EN 13890 ont été
remplacées par l’ISO 21832;
— des informations relatives à la digestion des capsules internes solubles dans l’acide ont été ajoutées
dans les Annexes C, D, E, F, G et H;
— le texte a fait l’objet d’une mise à jour rédactionnelle.
Une liste de toutes les parties de la série ISO 15202 se trouve sur le site Web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www .iso .org/ fr/ members .html.
iv © ISO 2020 – Tous droits réservés
Introduction
La santé des travailleurs dans de nombreuses industries est en danger du fait de l’exposition par
inhalation aux métaux et aux métalloïdes toxiques. Les hygiénistes industriels et autres professionnels
de santé publique ont besoin de déterminer l’efficacité des mesures prises pour contrôler l’exposition
des travailleurs et cela s’effectue en général en réalisant des mesurages de l’air du lieu de travail. Le
présent document a été publié dans le but de mettre à disposition une méthode permettant d’effectuer
des mesurages d’exposition valides pour un large éventail de métaux et de métalloïdes utilisés dans
l’industrie. Il sera utile aux organismes concernés par la santé et la sécurité sur le lieu de travail, aux
hygiénistes industriels et autres professionnels de santé publique, aux laboratoires d’analyses, aux
industriels utilisateurs de métaux et métalloïdes et à leurs employés.
L’ISO 15202, publiée en trois parties, spécifie une méthode générique pour la détermination de la
concentration en masse des métaux et métalloïdes sur le lieu de travail en utilisant la spectrométrie
d’émission atomique avec plasma à couplage inductif (ICP-AES):
— L’ISO 15202-1 donne les détails des Normes internationales, européennes et nationales appropriées
qui spécifient les caractéristiques, les exigences de performance et les méthodes d’essai se rapportant
à l’équipement de prélèvement. Elle complète les conseils donnés par ailleurs sur la stratégie
d’évaluation et la stratégie de mesurage et spécifie une méthode de prélèvement d’échantillons de
matière particulaire en suspension dans l’air en vue d’une analyse chimique ultérieure.
— L’ISO 15202-2 décrit plusieurs méthodes de préparation des solutions d’échantillons pour analyse
par ICP-AES.
— L’ISO 15202-3 définit les exigences et les méthodes d’essai pour l’analyse de solutions d’échantillons
par ICP-AES.
Les méthodes de préparation d’échantillons décrites dans la présente partie de l’ISO 15202 sont
généralement appropriées pour une utilisation avec d’autres techniques d’analyse que l’ICP-AES, par
exemple la spectrométrie d’absorption atomique (AAS) et la spectrométrie de masse avec plasma à
couplage inductif (ICP-MS).
Lors de l’élaboration du présent document, il a été présumé que les personnes chargées de l’exécution
de ses dispositions et de l’interprétation des résultats obtenus ont les qualifications et l’expérience
appropriées.
NORME INTERNATIONALE ISO 15202-2:2020(F)
Air des lieux de travail — Détermination des métaux et
métalloïdes dans les particules en suspension dans l'air
par spectrométrie d'émission atomique avec plasma à
couplage inductif —
Partie 2:
Préparation des échantillons
AVERTISSEMENT — L’utilisation du présent document peut impliquer l’emploi de produits et
la mise en œuvre de modes opératoires et d’appareillages à caractère dangereux. Le présent
document n’a pas pour but d’aborder tous les problèmes de sécurité liés à son utilisation. Il
incombe à l’utilisateur du présent document d’établir, avant de l’utiliser, des pratiques d’hygiène
et de sécurité appropriées et de déterminer l’applicabilité des restrictions réglementaires.
1 Domaine d’application
Le présent document spécifie plusieurs méthodes appropriées de préparation de solutions
...
NORME ISO
INTERNATIONALE 15202-2
Troisième édition
2020-05
Air des lieux de travail —
Détermination des métaux et
métalloïdes dans les particules
en suspension dans l'air par
spectrométrie d'émission atomique
avec plasma à couplage inductif —
Partie 2:
Préparation des échantillons
Workplace air — Determination of metals and metalloids in airborne
particulate matter by inductively coupled plasma atomic emission
spectrometry —
Part 2: Sample preparation
Numéro de référence
©
ISO 2020
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2020
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2020 – Tous droits réservés
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives . 2
3 Termes et définitions . 2
4 Principe . 3
5 Exigences . 3
6 Réactions . 4
7 Réactifs . 4
8 Appareillage de laboratoire . 4
9 Mode opératoire. 5
9.1 Composés solubles de métaux et métalloïdes . 5
9.2 Métaux et métalloïdes totaux et leurs composés . 5
9.3 Exposition mixte . 6
10 Cas particuliers . 6
10.1 Action à mener s’il existe un doute concernant l’efficacité de la méthode de mise
en solution d’échantillon choisie . 6
10.2 Action à mener lorsque les particules se sont détachées du filtre pendant le transport . 7
10.3 Action à mener en présence de dépôts sur les parois du dispositif de prélèvement . 7
11 Enregistrements de laboratoire . 7
Annexe A (informative) Précautions de sécurité à respecter lors de l’utilisation d’acide
fluorhydrique et perchlorique . 8
Annexe B (normative) Méthode de mise en solution d’échantillon pour les composés
solubles de métaux et métalloïdes . 9
Annexe C (normative) Mise en solution d’échantillon à l’aide d’acide nitrique et d’acide
chlorhydrique sur plaque chauffante .15
Annexe D (normative) Mise en solution d’échantillon à l’aide d’acide fluorhydrique et
d’acide nitrique par agitation par ultrason .19
Annexe E (normative) Mise en solution en utilisant de l’acide sulfurique et du peroxyde
d’hydrogène sur plaque chauffante .23
Annexe F (normative) Mise en solution en utilisant de l’acide nitrique et de l’acide
perchlorique sur plaque chauffante .28
Annexe G (normative) Mise en solution d’échantillon dans un système de digestion par
micro-ondes en récipient fermé .33
Annexe H (normative) Mise en solution d’échantillon à 95 °C sur bloc chauffant .39
Annexe I (normative) Action à mener en présence de particules visibles, non dissoutes,
après mise en solution d’échantillon .43
Annexe J (informative) Dépôts sur les parois des dispositifs de prélèvement .49
Bibliographie .52
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 146, Qualité de l’air, sous-comité SC 2,
Atmosphères des lieux de travail.
Cette troisième édition annule et remplace la deuxième édition (ISO 15202-2:2012), qui a fait l’objet
d’une révision technique. Les principales modifications par rapport à l’édition précédente sont les
suivantes:
— les définitions figurant dans l’ISO 18158 ont été supprimées de l’ISO 15202-2, et la référence à
l’ISO 18158 a été ajoutée en remplacement des références à l’EN 1540;
— les références à l’EN 482 ont été remplacées par l’ISO 20581, et les références à l’EN 13890 ont été
remplacées par l’ISO 21832;
— des informations relatives à la digestion des capsules internes solubles dans l’acide ont été ajoutées
dans les Annexes C, D, E, F, G et H;
— le texte a fait l’objet d’une mise à jour rédactionnelle.
Une liste de toutes les parties de la série ISO 15202 se trouve sur le site Web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www .iso .org/ fr/ members .html.
iv © ISO 2020 – Tous droits réservés
Introduction
La santé des travailleurs dans de nombreuses industries est en danger du fait de l’exposition par
inhalation aux métaux et aux métalloïdes toxiques. Les hygiénistes industriels et autres professionnels
de santé publique ont besoin de déterminer l’efficacité des mesures prises pour contrôler l’exposition
des travailleurs et cela s’effectue en général en réalisant des mesurages de l’air du lieu de travail. Le
présent document a été publié dans le but de mettre à disposition une méthode permettant d’effectuer
des mesurages d’exposition valides pour un large éventail de métaux et de métalloïdes utilisés dans
l’industrie. Il sera utile aux organismes concernés par la santé et la sécurité sur le lieu de travail, aux
hygiénistes industriels et autres professionnels de santé publique, aux laboratoires d’analyses, aux
industriels utilisateurs de métaux et métalloïdes et à leurs employés.
L’ISO 15202, publiée en trois parties, spécifie une méthode générique pour la détermination de la
concentration en masse des métaux et métalloïdes sur le lieu de travail en utilisant la spectrométrie
d’émission atomique avec plasma à couplage inductif (ICP-AES):
— L’ISO 15202-1 donne les détails des Normes internationales, européennes et nationales appropriées
qui spécifient les caractéristiques, les exigences de performance et les méthodes d’essai se rapportant
à l’équipement de prélèvement. Elle complète les conseils donnés par ailleurs sur la stratégie
d’évaluation et la stratégie de mesurage et spécifie une méthode de prélèvement d’échantillons de
matière particulaire en suspension dans l’air en vue d’une analyse chimique ultérieure.
— L’ISO 15202-2 décrit plusieurs méthodes de préparation des solutions d’échantillons pour analyse
par ICP-AES.
— L’ISO 15202-3 définit les exigences et les méthodes d’essai pour l’analyse de solutions d’échantillons
par ICP-AES.
Les méthodes de préparation d’échantillons décrites dans la présente partie de l’ISO 15202 sont
généralement appropriées pour une utilisation avec d’autres techniques d’analyse que l’ICP-AES, par
exemple la spectrométrie d’absorption atomique (AAS) et la spectrométrie de masse avec plasma à
couplage inductif (ICP-MS).
Lors de l’élaboration du présent document, il a été présumé que les personnes chargées de l’exécution
de ses dispositions et de l’interprétation des résultats obtenus ont les qualifications et l’expérience
appropriées.
NORME INTERNATIONALE ISO 15202-2:2020(F)
Air des lieux de travail — Détermination des métaux et
métalloïdes dans les particules en suspension dans l'air
par spectrométrie d'émission atomique avec plasma à
couplage inductif —
Partie 2:
Préparation des échantillons
AVERTISSEMENT — L’utilisation du présent document peut impliquer l’emploi de produits et
la mise en œuvre de modes opératoires et d’appareillages à caractère dangereux. Le présent
document n’a pas pour but d’aborder tous les problèmes de sécurité liés à son utilisation. Il
incombe à l’utilisateur du présent document d’établir, avant de l’utiliser, des pratiques d’hygiène
et de sécurité appropriées et de déterminer l’applicabilité des restrictions réglementaires.
1 Domaine d’application
Le présent document spécifie plusieurs méthodes appropriées de préparation de solutions
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.