SIST EN 60317-0-7:2012
(Main)Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm
Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm
This part of IEC 60317 establishes general requirements for fully insulated (FIW) zero-defect enamelled round copper wires. The nominal conductor diameter range is given in the relevant technical specification.
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-7: Allgemeine Anforderungen - Isolationsfehlerfreie Runddrähte (FIW) aus Kupfer, lackisoliert mit Nenndurchmesser von 0,040 mm bis 1,600 mm
Spécifications pour types particuliers de fils de bobinage - Partie 0-7: Exigences générales - Fil de section circulaire en cuivre émaillé sans défaut d'isolation électrique avec diamètre nominal de conducteur compris entre 0,040 mm et 1,600 mm
La CEI 60317-0-7:2012 établit les exigences générales d'un fil de bobinage isolé en continu (FIW: Fully Insulated Wire), sans défaut d'isolation électrique, de section circulaire en cuivre émaillé. La gamme des diamètres nominaux des conducteurs est donnée dans la spécification technique appropriée.
Specifikacije za posebne vrste navijalnih žic - 0-7. del: Splošne zahteve - Popolnoma izolirana in brezhibno lakirana okrogla bakrena žica z nazivnim premerom vodnika od 0,040 mm do 1,600 mm
Ta del IEC 60317 določa splošne zahteve za popolnoma izolirane in brezhibno lakirane okrogle bakrene žice. Razpon nazivnega premera prevodnika je naveden v ustrezni tehnični specifikaciji.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60317-0-7:2012
01-september-2012
Specifikacije za posebne vrste navijalnih žic - 0-7. del: Splošne zahteve -
Popolnoma izolirana in brezhibno lakirana okrogla bakrena žica z nazivnim
premerom vodnika od 0,040 mm do 1,600 mm
Specifications for particular types of winding wires - Part 0-7: General requirements -
Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor
diameter of 0,040 mm to 1,600 mm
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-7:
Allgemeine Anforderungen - Isolationsfehlerfreie Runddrähte (FIW) aus Kupfer,
lackisoliert mit Nenndurchmesser von 0,040 mm bis 1,600 mm
Spécifications pour types particuliers de fils de bobinage - Partie 0-7: Exigences
générales - Fil de section circulaire en cuivre émaillé sans défaut d'isolation électrique
avec diamètre nominal de conducteur compris entre 0,040 mm et 1,600 mm
Ta slovenski standard je istoveten z: EN 60317-0-7:2012
ICS:
29.060.10 Žice Wires
SIST EN 60317-0-7:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 60317-0-7
NORME EUROPÉENNE
June 2012
EUROPÄISCHE NORM
ICS 29.060.10
English version
Specifications for particular types of winding wires -
Part 0-7: General requirements -
Fully insulated (FIW) zero-defect enamelled round copper wire with
nominal conductor diameter of 0,040 mm to 1,600 mm
(IEC 60317-0-7:2012)
Spécifications pour types particuliers de Technische Lieferbedingungen für
fils de bobinage - bestimmte Typen von Wickeldrähten -
Partie 0-7: Exigences générales - Teil 0-7: Allgemeine Anforderungen -
Fil de section circulaire en cuivre émaillé Isolationsfehlerfreie Runddrähte (FIW) aus
sans défaut d'isolation électrique avec Kupfer, lackisoliert mit Nenndurchmesser
diamètre nominal de conducteur compris von 0,040 mm bis 1,600 mm
entre 0,040 mm et 1,600 mm (IEC 60317-0-7:2012)
(CEI 60317-0-7:2012)
This European Standard was approved by CENELEC on 2012-05-24. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-0-7:2012 E
---------------------- Page: 2 ----------------------
EN 60317-0-7:2012 - 2 -
Foreword
The text of document 55/1303/FDIS, future edition 1 of IEC 60317-0-7, prepared by IEC/TC 55 "Winding
wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-0-
7:2012.
The following dates are fixed:
(dop) 2013-02-24
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-05-24
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This European Standard is to be read in conjunction with the EN 60851 series.
The clause numbers used in EN 60317-0-7:2012 are identical with the respective test numbers of the
EN 60851 series.
In case of inconsistencies between EN 60851 and EN 60317-0-7:2012, the latter shall prevail.
The numbering of clauses in this standard is not continuous from Clauses 21 and 30 in order to reserve
space for possible future wire requirements prior to those for wire packaging.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 60317-0-7:2012 was approved by CENELEC as a European
Standard without any modification.
---------------------- Page: 3 ----------------------
- 3 - EN 60317-0-7:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60172 - Test procedure for the determination of the EN 60172 -
temperature index of enamelled winding wires
IEC 60317-0-1 2008 Specifications for particular types of winding EN 60317-0-1 2008
wires -
Part 0-1: General requirements - Enamelled
round copper wire
IEC 60851 Series Winding wires - Test methods EN 60851 Series
IEC 60851-5 2008 Winding wires - Test methods - EN 60851-5 2008
+ A1 2011 Part 5: Electrical properties + A1 2011
ISO 3 - Preferred numbers - Series of preferred - -
numbers
---------------------- Page: 4 ----------------------
IEC 60317-0-7
®
Edition 1.0 2012-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 0-7: General requirements – Fully insulated (FIW) zero-defect enamelled
round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm
Spécifications pour types particuliers de fils de bobinage –
Partie 0-7: Exigences générales – Fil de section circulaire en cuivre émaillé sans
défaut d'isolation électrique avec diamètre nominal de conducteur compris entre
0,040 mm et 1,600 mm
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
R
CODE PRIX
ICS 29.060.10 ISBN 978-2-8322-0079-7
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 5 ----------------------
– 2 – 60317-0-7 IEC:2012
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, general notes and appearance . 7
3.1 Terms and definitions . 7
3.2 General notes. 9
3.2.1 Methods of test . 9
3.2.2 Winding wire . 9
3.3 Appearance . 9
4 Dimensions . 9
4.1 Conductor diameter . 9
4.2 Out of roundness of conductor (for nominal diameters over 0,063 mm). 10
4.3 Minimum overall diameter . 10
4.4 Maximum overall diameter . 10
5 Electrical resistance . 13
6 Elongation . 13
7 Springiness . 14
8 Flexibility and adherence . 14
8.1 Mandrel winding test (for nominal conductor diameters up to and including
1,600 mm) . 14
8.2 Jerk test (for nominal diameters up to and including 1,000 mm) . 15
9 Heat shock . 15
10 Cut Through . 16
11 Resistance to abrasion . 16
12 Resistance to solvents . 16
13 Breakdown voltage . 17
14 Continuity of insulation (nominal conductor diameters up to and including
1,600 mm) . 17
14.1 Off-line high voltage continuity . 17
14.2 In-line high voltage continuity . 17
15 Temperature index . 17
16 Resistance to refrigerants . 17
17 Solderability . 18
18 Heat or solvent bonding . 18
19 Dielectric dissipation factor . 18
20 Resistance to transformer oil . 18
21 Loss of mass . 18
23 Pin-hole test . 18
30 Packaging . 18
Annex A (informative) Dimensions for intermediate nominal conductor diameter values
(R 40) . 19
---------------------- Page: 6 ----------------------
60317-0-7 IEC:2012 – 3 –
Table 1 – Dimensions of enamelled wires (R 20) (1 of 2) . 11
Table 2 – Electrical resistance . 13
Table 3 – Elongation at break . 13
Table 4 – Springiness . 14
Table 5 – Mandrel diameters for mandrel winding test . 15
Table 6 – Heat shock . 16
Table 7 – Breakdown voltage . 17
Table A.1 – Dimensions of enamelled wires without a bonding layer (R 40) . 19
---------------------- Page: 7 ----------------------
– 4 – 60317-0-7 IEC:2012
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –
Part 0-7: General requirements –
Fully insulated (FIW) zero-defect enamelled round copper wire
with nominal conductor diameter of 0,040 mm to 1,600 mm
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60317-0-7 has been prepared by IEC technical committee 55:
Winding wires.
The text of this standard is based on the following documents:
FDIS Report on Voting
55/1303/FDIS 55/1321/RVD
Full information on the voting for the approval of this part can be found in the report on voting
indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 8 ----------------------
60317-0-7 IEC:2012 – 5 –
This International standard is to be read in conjunction with the IEC 60851 series. The clause
numbers used in this part of IEC 60317 are identical with the respective test numbers of the
IEC 60851 series.
In case of inconsistencies between IEC 60851 and this part of IEC 60317, the latter shall
prevail.
The numbering of clauses in this standard is not continuous from Clauses 21 and 30 in order
to reserve space for possible future wire requirements prior to those for wire packaging.
A list of all the parts in the IEC 60317 series, published under the general title Specifications
for particular types of winding wires can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 9 ----------------------
– 6 – 60317-0-7 IEC:2012
INTRODUCTION
This part of IEC 60317 is one of a series which deals with insulated wires used for windings in
electrical equipment. The series has three groups describing:
1) Winding wires – Test methods (IEC 60851 series);
2) Specifications for particular types of winding wires (IEC 60317 series);
3) Packaging of winding wires (IEC 60264 series).
---------------------- Page: 10 ----------------------
60317-0-7 IEC:2012 – 7 –
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –
Part 0-7: General requirements –
Fully insulated (FIW) zero-defect enamelled round copper wire
with nominal conductor diameter of 0,040 mm to 1,600 mm
1 Scope
This part of IEC 60317 establishes general requirements for fully insulated (FIW) zero-defect
enamelled round copper wires.
The nominal conductor diameter range is given in the relevant technical specification.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60172, Test procedure for the determination of the temperature index of enamelled
winding wires
IEC 60317-0-1:2008, Specifications for particular types of winding wires – Part 0-1: General
requirements – Enamelled round copper wire
IEC 60851 (all parts), Winding wires – Test methods
IEC 60851-5:2008, Winding wires – Test methods – Part 5: Electrical properties
Amendment 1:2011
ISO 3, Preferred numbers – Series of preferred numbers
3 Terms, definitions, general notes and appearance
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1.1
bonding layer
material that is deposited on an enamelled wire and that has the specific function of bonding
wires together
3.1.2
class
thermal performance of a wire expressed by the temperature index and the heat shock
temperature
---------------------- Page: 11 ----------------------
– 8 – 60317-0-7 IEC:2012
3.1.3
coating
material that is deposited on a conductor or wire by suitable means and then dried and/or
cured
3.1.4
conductor
bare metal after removal of the insulation
3.1.5
crack
opening in the insulation that exposes the conductor to view at the stated magnification
3.1.6
dual coating
insulation composed of two different materials, an underlying and a superimposed coating
3.1.7
enamelled wire
wire coated with an insulation of cured resin
3.1.8
grade of FIW
range of overall diameter of a wire
Note 1 to entry: This note applies to the French language only.
3.1.9
insulation
coating or covering on the conducto
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.